|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [XenPPC] Booting Dom0 with SLES10 on JS21
Xenidis wrote:
>>> if you take this initrd and copy to you build machine, then:
>>> 1. $ gzip -c initrd > ramdisk.image.gz
>>> 2. $ cp ramdisk.image.gc <linux build>/arch/powerpc/boot
>
>totally my fault.
>turns out that the initrd is already compressed to thats:
> $ cp initrd <linux build>/arch/powerpc/boot/ramdisk.image.gz
>
>>> 3. $ make <linux flags> zImage.initrd
>>>
>>> Then try using <linux build>/arch/powerpc/boot/zImage.initrd as your
>>> Dom0
Much better... However still endup with:
INIT: Id "1" respawning too fast: disabled for 5 minutes
Also Linux seems to start twice?
SLOF
u4 DDR2 memory controller setup
-------------------------------
> detecting DIMM configuration: 4096Mb @ 400Mhz, CL 3
> initializing memory :
[reset core clock: ]OK
[register setup : ]OK
[start DDR clock : ]OK
[memory init : ]OK
[auto calibration: ]OK
[initial scrub : ]OK
[background scrub: ]OK
[flush cache : ]OK
> initialization complete.
has started execution, serial console @ 2f8
Build Ref = hp@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Welcome to JS2x Open Firmware
Copyright International Business Machines Corporation 2004 - 2006
US Government Users Restricted Rights -- Use, duplication or
disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
Press "s" to enter Open Firmware.
Online CPUs: #0 #1 #2 #3
4 GB of RAM @ 400 MHz
Switching top HT bus to 800MHz...
Found controller: IBM 572E001
Found disk@0,1,0: IBM-ESXS ST973401SS 73.4GB
TPM result: 00c4 00000004 0 0 0 0
Stopping BMC watchdog...
PCIe:
1800 cap @ b0
max payload size: 256
max read req: 128
link width: 8
2000 cap @ b0
max payload size: 256
max read req: 128
link width: 0
2800 cap @ b0
max payload size: 256
max read req: 128
link width: 8
3000 cap @ b0
max payload size: 256
max read req: 128
link width: 0
===================== VPD =====================
Machine Type : 884451U
Machine Serial No. : KQ010D2
Hardware Revision : 4
Manuf. Date : 1006
Part Number : 41Y5249
FRU Number : 32R2429
FRU Serial No. : ZK12HJ63119N
UUID : aa0a5f281dfb11b2a2b2001125c91ac8
Firmware Rel. date : 05/15/2006
Firmware Release : 001
Firmware Build ID : SLOF_620
The currently active flashside is: 1 (temporary)
Booting from Network
Bootloader 1.4
Reading MAC address from device: 00:11:25:C9:1A:C9
Requesting IP address via BOOTP: 30arp9.2.72.88
Requesting file "lab088/xen" via TFTP
Receiving data:
[...]
TFTP: Received lab088/xen (6677 KBytes)
---------------------------------------------------
OF: Xen/PPC version 3.0-unstable (poff@xxxxxxxxxxxxxx) (gcc version 3.4.1) Fri
Jul 7 17:59:06 EDT 2006
boot_of_init args: 0x0 0x0 0x111027c 0x0 0x0
boot msr: 0x1000000000003000
boot_of_init: _start 0000000003000100 _end 0000000003698ab0 0x0
boot_of_probemem: memory 0x0000000000000000[0x80000000]
boot_of_probemem: memory 0x0000000100000000[0x80000000]
bootargs =
boot_of_module: linked in module copied after _end (start 0x0000000003067f64
size 0x601019)
find_space base=0x0000000003698ab0 eomem=0x0000000080000000 size=0x00601019
align=0x1000
boot_of_module: mod[0] @ 0x0000000003699000[0x3c9a019]
find_space base=0x0000000003c9a019 eomem=0x0000000080000000 size=0x00030000
align=0x1000
creating oftree
pkg_save: saved device tree in 0x3ef8 bytes
boot_of_module: mod[1] @ 0x0000000003c9b000[0x3ccb000]
Pruning from devtree: /ht/isa@8/serial@3f8
since Xen will be using it for console
boot_of_serial: ISA base: 0xf4000000
boot_of_serial: ISRC=0x44, but forcing poll mode
OF: timebase-frequency = 14318478 Hz
OF: clock-frequency = 2300000 KHz
__ __ _____ ___ _ _ _
\ \/ /___ _ __ |___ / / _ \ _ _ _ __ ___| |_ __ _| |__ | | ___
\ // _ \ '_ \ |_ \| | | |__| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
/ \ __/ | | | ___) | |_| |__| |_| | | | \__ \ || (_| | |_) | | __/
/_/\_\___|_| |_| |____(_)___/ \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
http://www.cl.cam.ac.uk/netos/xen
University of Cambridge Computer Laboratory
Xen version 3.0-unstable (poff@xxxxxxxxxxxxxx) (gcc version 3.4.1) Tue Jul 11
13:12:14 EDT 2006
Latest ChangeSet: Fri Jul 07 13:57:26 2006 -0500 11082:b11a2c7b2989
(XEN) Physical RAM map:
(XEN) 0000000000000000 - 0000000080000000 (usable)
(XEN) 0000000100000000 - 0000000180000000 (usable)
(XEN) found a hole skipping remainder of memory at:
(XEN) 0000000100000000 and beyond
(XEN) System RAM: 2048MB (2097152kB)
(XEN) modules at: 0000000003699000 - 0000000003ccb000
(XEN) moved to: 0000000003699000 - 0000000003ccb000
(XEN) Xen heap: 47MB (49068kB)
(XEN) stack is here: 0000000000020000
(XEN) hid0: 0x0051118180000000
(XEN) xen_mpic_init: start
(XEN) mpic: Setting up MPIC "Xen-U3-MPIC" version 1.2 at f8040000, max 4 CPUs
(XEN) mpic: ISU size: 124, shift: 7, mask: 7f
(XEN) mpic: Initializing for 124 sources
(XEN) mpic: Setting up HT PICs workarounds for U3/U4
(XEN) mpic: - HT:07.0 [0xf0] vendor 1022 device 7460 has 24 irqs
(XEN) xen_mpic_init: success
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing DART 0xf8033000: tbl: 0000000000200000[0x200] entries:
0x80000
(XEN) Initializing DART Model U4: ctl: 0x88000000 base: 0x200 size: 0x200
(XEN) clearing RMO: 0x4000000[0x4000000]
(XEN) htab_alloc: dom0 sdr1: 100002
(XEN) Scrubbing Free RAM: .....................done.
(XEN) ELF program headers extend beyond end of image.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) xen_start_info: 0000000007ffe000
(XEN) shared_info: 0x3fff000,0000000007fff000
(XEN) loading OFH: 0x6000000, RMA: 0x2000000
(XEN) loading OFD: 0x6013000 RMA: 0x2013000, 0x30000
(XEN) loading 32-bit Dom0: 0x4400000, in RMA:0x400000
(XEN) DOM: pc = 0x400010, r2 = 0x0
(XEN) Add /openprom props
(XEN) Add /options props
(XEN) Add /cpus props
(XEN) Add /chosen props
(XEN) DOM0 bootargs: root=/dev/sda3
(XEN) Remove /chosen/mmu, stub will replace
(XEN) fix /memory@0 props
(XEN) fix /xen props
(XEN) Remove original /dart
(XEN) Remove original /rtas
(XEN) Xen trace buffers: disabled
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to
Xen).
zImage starting: loaded at 0x00400000 (sp: 0x01ffff90)
Allocating 0x76a178 bytes for kernel ...
OF version = 'IBM,XenOF0.1'
Allocating 0x3498f9 bytes for initrd ...
initial ramdisk moving 0x1b6b000 <- 0x6a6000 (0x3498f9 bytes)
initrd head: 0x1f8b0800
gunzipping (0x1400000 <- 0x407000:0x6a5f16)...done 0x6dcb60 bytes
OF stdout device is: /xen/console
command line: root=/dev/sda3
memory layout at init:
alloc_bottom : 0000000001eb5000
alloc_top : 0000000004000000
alloc_top_hi : 0000000004000000
rmo_top : 0000000004000000
ram_top : 0000000004000000
Looking for displays
0000000000000000 : boot cpu 0000000000000000
copying OF device tree ...
Building dt strings...
Building dt structure...
Device tree strings 0x0000000001eb6000 -> 0x0000000001eb6460
Device tree struct 0x0000000001eb7000 -> 0x0000000001eb9000
Calling quiesce ...
returning from prom_init
xen_start_info at c000000003ffe000
magic xen-3.0-powerpc64HV
flags 3
shared_info 3fff000, c000000003fff000
store_mfn 0
store_evtchn 0
console_mfn 0
console_evtchn 0
Hello World I'm Maple Xen-LPAR!
<- xen_init_early
firmware_features = 0x40000a
Using Xen-Maple machine description
Found initrd at 0xc000000001b6b000:0xc000000001eb48f9
Found legacy serial port 0 for /ht/isa@8/serial@2f8
port=2f8, taddr=f40002f8, irq=ffffffffffffffff, clk=1843200, speed=19200
Starting Linux PPC64 #1 SMP Tue Jul 11 11:27:07 EDT 2006
-----------------------------------------------------
ppc64_pft_size = 0x14
ppc64_interrupt_controller = 0x1
physicalMemorySize = 0x4000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0x0000000000000000
htab_hash_mask = 0x1fff
-----------------------------------------------------
Linux version 2.6.17-Xen (poff@lab095) (gcc version 3.4.1) #1 SMP Tue Jul 11
11:27:07 EDT 2006
*** 0000 : CF000012
*** 0000 : Setup Arch
[boot]0012 Setup Arch
Adding PCI host bridge /ht
Found U3-HT PCI host bridge. Firmware bus number: 0->239
PCI Host 0, io start: 0; io end: 3fffff
Using Xen idle loop
*** 0000 : CF000015
*** 0000 : Setup Done
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: root=/dev/sda3
-> maple_init_IRQ
mpic: Setting up MPIC "U3-MPIC" version 1.2 at f8040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
mpic: Setting up HT PICs workarounds for U3/U4
mpic: - HT:07.0 [0xf0] vendor 1022 device 7460 has 24 irqs
<- maple_init_IRQ
PID hash table entries: 512 (order: 9, 4096 bytes)
Maple: Found RTC at IO 0x1070
firmware_features = 0x40000a
Using Xen-Maple machine description
Found initrd at 0xc000000001b6b000:0xc000000001eb48f9
Found legacy serial port 0 for /ht/isa@8/serial@2f8
port=2f8, taddr=f40002f8, irq=ffffffffffffffff, clk=1843200, speed=19200
Starting Linux PPC64 #1 SMP Tue Jul 11 11:27:07 EDT 2006
-----------------------------------------------------
ppc64_pft_size = 0x14
ppc64_interrupt_controller = 0x1
physicalMemorySize = 0x4000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0x0000000000000000
htab_hash_mask = 0x1fff
-----------------------------------------------------
Linux version 2.6.17-Xen (poff@lab095) (gcc version 3.4.1) #1 SMP Tue Jul 11
11:27:07 EDT 2006
*** 0000 : CF000012
*** 0000 : Setup Arch
[boot]0012 Setup Arch
Adding PCI host bridge /ht
Found U3-HT PCI host bridge. Firmware bus number: 0->239
PCI Host 0, io start: 0; io end: 3fffff
Using Xen idle loop
*** 0000 : CF000015
*** 0000 : Setup Done
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: root=/dev/sda3
mpic: Setting up MPIC "U3-MPIC" version 1.2 at f8040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
mpic: Setting up HT PICs workarounds for U3/U4
mpic: - HT:07.0 [0xf0] vendor 1022 device 7460 has 24 irqs
PID hash table entries: 512 (order: 9, 4096 bytes)
Maple: Found RTC at IO 0x1070
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
Memory: 53472k/65536k available (5504k kernel code, 12000k reserved, 1320k
data, 568k bss, 232k init)
Mount-cache hash table entries: 256
Brought up 1 CPUs
smp_xen_setup_cpu(0)
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 3366k freed
grant table at c000000000034000
Grant table initialized
NET: Registered protocol family 16
*** 0000 : Linux ppc64
*** 0000 : 2.6.17-Xen
Failed to request PCI IO region on PCI domain 0000
IOMMU table initialized, virtual merging enabled
-> maple_pcibios_fixup
<- maple_pcibios_fixup
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 3, 32768 bytes)
TCP bind hash table entries: 1024 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
rtas_flash: no firmware flash support
scan-log-dump not implemented on this system
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
Generic RTC Driver v1.07
isa bounce pool size: 16 pages
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 7.0.38-k4
Copyright (c) 1999-2006 Intel Corporation.
tg3.c:v3.60 (June 17, 2006)
eth0: Tigon3 [partno(none) rev 8100 PHY(5780)] (PCIX:133MHz:64-bit)
10/100/1000BaseT Ethernet 00:11:25:c9:1a:c8
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[76144000] dma_mask[40-bit]
eth1: Tigon3 [partno(none) rev 8100 PHY(5780)] (PCIX:133MHz:64-bit)
10/100/1000BaseT Ethernet 00:11:25:c9:1a:c9
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth1: dma_rwctrl[76144000] dma_mask[40-bit]
Xen virtual console successfully installed as ttyS0
Event-channel device installed.
blkif_init: reqs=64, pages=704, mmap_vstart=0xc000000003000000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: IDE controller at PCI slot 0000:00:08.1
AMD8111: chipset revision 3
AMD8111: 0000:00:08.1 (rev 03) UDMA133 controller
AMD8111: 100% native mode on irq 16
ide0: BM-DMA at 0x9020-0x9027, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x9028-0x902f, BIOS settings: hdc:pio, hdd:pio
ipr: IBM Power RAID SCSI Device Driver version: 2.1.3 (March 29, 2006)
ipr 0000:01:01.0: Found IOA with IRQ: 15
ipr 0000:01:01.0: Starting IOA initialization sequence.
ipr 0000:01:01.0: Adapter firmware version: 06160024
ipr 0000:01:01.0: IOA initialized.
scsi0 : IBM 572E Storage Adapter
Vendor: IBM-ESXS Model: ST973401SS Rev: B519
Type: Direct-Access ANSI SCSI revision: 05
scsi: unknown device type 31
Vendor: IBM Model: 572E001 Rev: 0150
Type: Unknown ANSI SCSI revision: 00
SCSI device sda: 143374000 512-byte hdwr sectors (73407 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write through w/ FUA
SCSI device sda: 143374000 512-byte hdwr sectors (73407 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write through w/ FUA
sda: sda1 sda2 sda3
sd 0:0:1:0: Attached scsi disk sda
sd 0:0:1:0: Attached scsi generic sg0 type 0
scsi 0:255:255:255: Attached scsi generic sg1 type 31
scsi1 : scsi_debug, version 1.75 [20050113], dev_size_mb=8, opts=0x0
Vendor: Linux Model: scsi_debug Rev: 0004
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 16384 512-byte hdwr sectors (8 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
SCSI device sdb: 16384 512-byte hdwr sectors (8 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
sdb: unknown partition table
sd 1:0:0:0: Attached scsi disk sdb
sd 1:0:0:0: Attached scsi generic sg2 type 0
ohci_hcd 0000:07:00.0: OHCI Host Controller
ohci_hcd 0000:07:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:07:00.0: irq 19, io mem 0xc0200000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:07:00.1: OHCI Host Controller
ohci_hcd 0000:07:00.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:07:00.1: irq 19, io mem 0xc0201000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v3.0
usbcore: registered new driver usbhid
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/input/hid-core.c: v2.6:USB HID
core driver
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
usbcore: registered new driver usbserial
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for generic
usbcore: registered new driver usbserial_generic
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
Driver core
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for DeLorme Earthmate USB
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for HID->COM RS232 Adapter
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for Nokia CA-42 V2 Adapter
usbcore: registered new driver cypress
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/cypress_m8.c: Cypress USB
to Serial Driver v1.09
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for Garmin GPS usb/tty
usbcore: registered new driver garmin_gps
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/garmin_gps.c: garmin gps
driver v0.23
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for IPWireless converter
usbcore: registered new driver ipwtty
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/ipw.c: IPWireless tty
driver v0.3
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for Keyspan - (without firmware)
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for Keyspan 1 port adapter
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for Keyspan 2 port adapter
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for Keyspan 4 port adapter
usbcore: registered new driver keyspan
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/keyspan.c: v1.1.4:Keyspan
USB to Serial Converter Driver
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for TI USB 3410 1 port adapter
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/usb-serial.c: USB Serial
support registered for TI USB 5052 2 port adapter
usbcore: registered new driver ti_usb_3410_5052
/home/poff/linux-ppc-2.6-work1.hg/drivers/usb/serial/ti_usb_3410_5052.c: TI USB
3410/5052 Serial Driver v0.9
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
IPv4 over IPv4 tunneling driver
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
ebt_ulog: not logging via ulog since somebody else already registered for
PF_BRIDGE
802.1Q VLAN Support v1.8 Ben Greear <greearb@xxxxxxxxxxxxxxx>
All bugs added by David S. Miller <davem@xxxxxxxxxx>
Freeing unused kernel memory: 232k freed
Starting udevd
Creating devices
Loading scsi_mod
FATAL: Could not load /lib/modules/2.6.17-Xen/modules.dep: No such file or
directory
Loading sd_mod
FATAL: Could not load /lib/modules/2.6.17-Xen/modules.dep: No such file or
directory
Loading firmware_class
FATAL: Could not load /lib/modules/2.6.17-Xen/modules.dep: No such file or
directory
Loading ipr
FATAL: Could not load /lib/modules/2.6.17-Xen/modules.dep: No such file or
directory
Waiting for device /dev/sda3 to appear: ok
rootfs: major=8 minor=3 devn=2051
fsck 1.38 (30-Jun-2005)
[/bin/fsck.reiserfs (1) -- /] fsck.reiserfs -a /dev/sda3
Reiserfs super block in block 16 on 0x4000 of format 3.6 with standard journal
Blocks (total/free): 17388352/16885299 by 4096 bytes
Filesystem is NOT clean
Replaying journal..
Trans replayed: mountid 47, transid 13197, desc 7135, len 2, commit 7138, next
trans offset 7121
Trans replayed: mountid 47, transid 13198, desc 7139, len 1, commit 7141, next
trans offset 7124
Reiserfs journal '/dev/sda3' in blocks [18..8211]: 2 transactions replayed
Checking internal tree..finished
fsck succeeded. Mounting root device read-write.
Mounting root /dev/sda3
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
ReiserFS: sda3: warning: acl not supported.
ReiserFS: sda3: warning: user_xattr not supported.
INIT: version 2.86 booting
INIT: Entering runlevel: 5
INIT: Id "1" respawning too fast: disabled for 5 minutes
INIT: Id "2" respawning too fast: disabled for 5 minutes
INIT: Id "cons" respawning too fast: disabled for 5 minutes
INIT: Id "3" respawning too fast: disabled for 5 minutes
INIT: Id "4" respawning too fast: disabled for 5 minutes
INIT: Id "5" respawning too fast: disabled for 5 minutes
INIT: Id "6" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
INIT: Id "1" respawning too fast: disabled for 5 minutes
INIT: Id "2" respawning too fast: disabled for 5 minutes
INIT: Id "3" respawning too fast: disabled for 5 minutes
INIT: Id "4" respawning too fast: disabled for 5 minutes
INIT: Id "5" respawning too fast: disabled for 5 minutes
INIT: Id "6" respawning too fast: disabled for 5 minutes
INIT: Id "cons" respawning too fast: disabled for 5 minutes
_______________________________________________
Xen-ppc-devel mailing list
Xen-ppc-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-ppc-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |