[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] Recommended Best way to Upgrade/Update Xen



humm, OK in that case, i guess i should be a little more detailed. I did:

- Debian Wheezy 64bit
- It was original installed with kernel 3.2.0-2-amd64
- Next compiled and installed kernel 3.3.4, where only modified .config to enabled all Xen options
- Rebooted into kernel 3.3.4 to make sure it works first. (Didn't remove kernel 3.2.0-2-amd64 in case of issues)
- Compiled and installed Xen 4.2-unstable with the latest changeset 25269
- Rebooted into Xen 4.2-unstable using kernel 3.3.4

So you do some testing in Xen 4.2-unstable, to make sure the latest updates to the Xen 4.2-unstable source didn't mess something up. But, if you need to go back to a previous changest, OR even downgrade to Xen 4.1.2, would you:

A.) Reboot into kernel 3.3.4 without xen, do a complete remove of Xen 4.2-unstable (using synaptic sudo apt-get autoremove xen*** or similar), than install the next package you want to test, and reboot into Xen*** with Kernel 3.3.4?

B.) OR boot into kernel 3.3.4 without xen, and install the newly built Xen DEB package without first removing it, which will overwrite all current files and directories with the new one?

For the sake making it simpler to test a bunch of changesets, nothing else was changed or removed, not the /etc/network/interfaces, or /etc/modules, didn't update grub.cfg until the new Xen was installed, and only Xen was removed / reinstalled.
 


This is a good question to know.  Much will depend on what you mean by "Xen" and updating "Xen".

In my particular case, I run generic Distro-based Xen 3.0.x under CentOS 5.7, and will be upgrading to GITCO-based Xen 4.1.2.  My upgrade steps are

Distribution Install:

# yum update
# yum groupinstall Xen
==> or yum groupinstall Virtualization, before CentOS 5.8 had been released.
# vi /etc/grub.conf
==> change default= to use the Xen kernel= stanza.
# reboot

Upgrade install to 4.1.2:

# cd /etc/yum.repos.d
# rpm -e --nodeps libvirt.i386
# rpm -e --nodeps libvirt.x86_64
# rpm -e --nodeps libvirt-python
# yum update
# vi /etc/grub.conf
==> consider whether your hardware requires pci=nomsi on the module=vmlinuz line of the active stanzas.  Dell R610 with MegaRAID requires it.
# reboot

--Andy


On Thu, May 10, 2012 at 4:30 PM, <cyberhawk001@xxxxxxxxx> wrote:
This might be a silly question for most, but since Xen is ever so changing with regular changesets and updates, what is the "best practice" way to upgrade / update or even downgrade Xen?

1.) Is it by booting into regular Linux Kernel without Xen, do a complete uninstall of the old Xen, than install the newly compiled Xen?

2.) Is it by booting into regular Linux Kernel without Xen, than install the newly compiled Xen, were it will / should overwrite everything with the new version?



_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxx
http://lists.xen.org/xen-users


_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxx
http://lists.xen.org/xen-users

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.