[Xen-users] 64 bit Memory and IO resources & pciback

[Morten BÃgeskov <xen-users@xxxxxxxxxxxxxxxxxx>]

Hello...

I run into a situation...
I've been more or less forced into using PAE (I would like 2.6.23 ;-)
This however results in something undesired.

PAE automatically selects "64 bit Memory and IO resources"  
CONFIG_RESOURCES_64BIT
However
"exporting" a Hauppauge PVR-500 & USB2 controller

Wether I use
  PCI Backend Mode (Passthrough)
  PCI Backend Mode (Virtual PCI)

xen-3.1.0: Non-PAE, No RESOURCES_64BIT => success
xen-3.1.0: Non-PAE, RESOURCES_64BIT => failure
xen-3.1.0: PAE, RESOURCES_64BIT => failure

success means I can record tv & see usb-devices.
failure? see below.

Does anybosy know a kernel option that I need to pass to get this to work.

when using RESOURCES_64BIT I get this in my domU console:

PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ohci_hcd 0000:00:0a.0: init 0000:00:0a.0 fail, -14
ohci_hcd: probe of 0000:00:0a.0 failed with error -14
PCI: Enabling device 0000:00:0a.1 (0000 -> 0002)
ohci_hcd 0000:00:0a.1: init 0000:00:0a.1 fail, -14
ohci_hcd: probe of 0000:00:0a.1 failed with error -14
PCI: Enabling device 0000:00:0a.2 (0000 -> 0002)
ehci_hcd 0000:00:0a.2: init 0000:00:0a.2 fail, -14
ehci_hcd: probe of 0000:00:0a.2 failed with error -14

And

ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 1.0.0 (2.6.18-xenU-video mod_unload K7 gcc-4.1) loading
ivtv0: Autodetected Hauppauge card (cx23416 based)
PCI: Enabling device 0000:02:08.0 (0000 -> 0002)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039
tveeprom 0-0050: Hauppauge model 23559, rev D496, serial# 9481257
tveeprom 0-0050: tuner model is Samsung TCPG 6121P30A (idx 96, type 73)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)  
(eeprom 0x74)
tveeprom 0-0050: second tuner model is Philips TEA5768HL FM Radio (idx  
101, type 62)
tveeprom 0-0050: audio processor is CX25843 (idx 37)
tveeprom 0-0050: decoder processor is CX25843 (idx 30)
tveeprom 0-0050: has radio, has no IR remote
ivtv0: Autodetected WinTV PVR 500 (unit #1)
tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0)
tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner)
tuner 0-0060: TEA5767 detected.
tuner 0-0060: chip found @ 0xc0 (ivtv i2c driver #0)
tuner 0-0060: type set to 62 (Philips TEA5767HN FM Radio)
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
tuner 0-0061: type set to 73 (Samsung TCPG 6121P30A)
ivtv0: Registered device video0 for encoder MPEG (4 MB)
ivtv0: Registered device video32 for encoder YUV (2 MB)
ivtv0: Registered device vbi0 for encoder VBI (1 MB)
ivtv0: Registered device video24 for encoder PCM audio (1 MB)
ivtv0: Registered device radio0 for encoder radio
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv:  ======================  NEXT CARD  ======================
ivtv1: Autodetected Hauppauge card (cx23416 based)
PCI: Enabling device 0000:02:09.0 (0000 -> 0002)
ivtv1: Cannot request encoder memory region on card 1.
ivtv1: Error -5 on initialization



_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users