I successfully installed xen3.0 on my machines. However there are a few problems when I try to create a new domain!
The procedure I've followed is pretty much the same as given on pages 4-5 on;
http://www.howtoforge.com/perfect_setup_xen3_debian_p4On doing a ' xm create -c /etc/xen/vm1-config.sxp vmid=1' the following is what parts of the trace look like:
NET: Registered protocol family 20
Using IPI No-Shortcut mode
EXT2-fs warning (device hda1): ext2_fill_super: mounting ext3 filesystem as ext2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 168k freed
8250: no version for "struct_module" found: kernel tainted.
8250: Unknown symbol uart_get_baud_rate
8250: Unknown symbol uart_resume_port
8250: Unknown symbol uart_register_driver
8250: Unknown symbol uart_suspend_port
8250: Unknown symbol uart_remove_one_port
8250: Unknown symbol uart_update_timeout
8250: Unknown symbol uart_unregister_driver
8250: Unknown symbol uart_get_divisor
8250: Unknown symbol uart_match_port
8250: Unknown symbol uart_add_one_port
8250: Unknown symbol uart_write_wakeup
modprobe: FATAL: Error inserting 8250 (/lib/modules/2.6.16-xen/kernel/drivers/serial/8250.ko): Unknown symbol in module, or unknown parameter (see dmesg)
INIT: version 2.86 booting
* Files under mount point '/dev/shm' will be hidden.
Will now activate swap.
swapon on /dev/hda2
swapon: cannot stat /dev/hda2: No such file or directory
* Swap activation failed with error code 255.
Will now check root file system.
fsck 1.39-WIP (31-Dec-2005)
[/sbin/fsck.ext3 (1) -- /dev/shm/root] fsck.ext3 -a -C0 /dev/shm/root
/dev/shm/root: clean, 25155/640000 files, 193537/1280000 blocks
Will now mount local filesystems.
mount: mount point devpts does not exist
none on /dev/shm type tmpfs (rw)
* Mounting local filesystems failed with error code 96.
Will now activate swapfile swap.
Done activating swapfile swap.
* /etc/network/options is deprecated.
Setting up IP spoofing protection...done (rp_filter).
Configuring network interfaces...done.
Starting portmap daemon....
Starting deferred execution scheduler: atd.
Starting periodic command scheduler....
INIT: Id "1" respawning too fast: disabled for 5 minutes
INIT: Id "2" respawning too fast: disabled for 5 minutes
INIT: Id "5" respawning too fast: disabled for 5 minutes
INIT: Id "3" respawning too fast: disabled for 5 minutes
INIT: Id "4" respawning too fast: disabled for 5 minutes
INIT: Id "6" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
INIT: Id "1" respawning too fast: disabled for 5 minutes
INIT: Id "2" respawning too fast: disabled for 5 minutes
INIT: Id "5" respawning too fast: disabled for 5 minutes
INIT: Id "3" respawning too fast: disabled for 5 minutes
INIT: Id "4" respawning too fast: disabled for 5 minutes
INIT: Id "6" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
my /etc/fstab for this machine looks like:
proc /proc proc defaults 0 0
/dev/hda1 / ext3 defaults,errors=remount-ro 0 1
/dev/hda5 none swap sw 0 0
and the domain configuration file is attahed.
Any sort of help would be appreciated! I've been stuck here since pretty long :(
Regards,
Hardeep
--
