|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: AW: AW: Xenstore failed to start / Xenalyze on ARM ( NXP S32G3 with Cortex-A53)
On Tue, 7 Feb 2023, El Mesdadi Youssef ESK UILD7 wrote: > > hello Julien, > > >first of all thank you so much for the support, after flashing Xen on the > >S32G3 I noticed that I cannot create DomUs. > >when I also give the xl list, it does not even show Dom0 and stays blocked. > > root@s32g399aevb3:~# xl list > Name ID Mem VCPUs State > Time(s) > > root@s32g399aevb3:~# This is usually due to the init script (/etc/init.d/xencommons or systemd scripts) hanging or crashing. As a consequence xenstored doesn't get launched properly. > >I assume this is because xenstore failed to start, the error is shown in the > >messages during the boot time. > > [FAILED] Failed to start The Xen xenstore. > See 'systemctl status xenstored.service' for details. You need to fix this. A couple of options: - ignore the systemd scripts, and instead try to execute manually bash /etc/init.d/xencommons start - try to launch xenstored manually with: xenstored & - have a look at the way Yocto meta-virtualization sets up the systemd init scripts as this seems to be a "distro" error https://github.com/lgirdk/meta-virtualization/blob/master/recipes-extended/xen/xen-tools.inc - switch from systemd to SysVinit > [FAILED] Failed to mount NFSD configuration filesystem. > See 'systemctl status proc-fs-nfsd.mount' for details. > > >Here is xl.conf in case you need information about this file: > > root@s32g399aevb3:/etc/xen# cat xl.conf > ## Global XL config file ## > > # Set domain-id policy. "xen" means that the hypervisor will choose the > # id of a new domain. "random" means that a random value will be chosen. > #domid_policy="xen" > > # Control whether dom0 is ballooned down when xen doesn't have enough > # free memory to create a domain. "auto" means only balloon if dom0 > # starts with all the host's memory. > #autoballoon="auto" > > # full path of the lockfile used by xl during domain creation > #lockfile="/var/lock/xl" > > # default output format used by "xl list -l" > #output_format="json" > > # first block device to be used for temporary VM disk mounts > #blkdev_start="xvda" > > # default option to run hotplug scripts from xl > # if disabled the old behaviour will be used, and hotplug scripts will be > # launched by udev. > #run_hotplug_scripts=1 > > # default backend domain to connect guest vifs to. This can be any > # valid domain identifier. > #vif.default.backend="0" > > # default gateway device to use with vif-route hotplug script > #vif.default.gatewaydev="eth0" > > # default vif script to use if none is specified in the guest config > #vif.default.script="vif-bridge" > > # default bridge device to use with vif-bridge hotplug scripts > #vif.default.bridge="xenbr0" > > # Reserve a claim of memory when launching a guest. This guarantees immediate > # feedback whether the guest can be launched due to memory exhaustion > # (which can take a long time to find out if launching huge guests). > # see xl.conf(5) for details. > #claim_mode=1 > > # Specify global vcpu hard affinity masks. See xl.conf(5) for details. > #vm.cpumask="0-7" > #vm.pv.cpumask="0-3" > #vm.hvm.cpumask="3-7" > > > >next are the messages during the boot time: > > NOTICE: Reset status: Power-On Reset > NOTICE: BL2: v2.5(release):bsp33.0-2.5-dirty > NOTICE: BL2: Built : 14:01:09, Jun 15 2022 > NOTICE: BL2: Booting BL31 > > > U-Boot 2020.04+g9cdfca686e (Jun 10 2022 - 11:46:41 +0000) > > CPU: NXP S32G399A rev. 1.0 > Model: NXP S32G3XXX-EVB > DRAM: 3.5 GiB > MMC: FSL_SDHC: 0 > Loading Environment from MMC... OK > Using internal clock for PCIe0, CRNS > Configuring PCIe0 as RootComplex(x2) > Using internal clock for PCIe1, CRNS > Frequency 100Mhz configured for PCIe1 > Configuring PCIe1 as SGMII [XPCS0 1G, XPCS1 OFF(PCIex1)] > Setting PCI Device and Vendor IDs to 0x4300:0x1957 > PCIe0: Failed to get link up > Pcie0: LINK_DBG_1: 0x00000000, LINK_DBG_2: 0x00000800 (expected 0x000000d1) > DEBUG_R0: 0x00ed4001, DEBUG_R1: 0x08600000 > PCI: Failed autoconfig bar 1c > PCIe1: Not configuring PCIe, PHY not configured > In: serial@401c8000 > Out: serial@401c8000 > Err: serial@401c8000 > Loading SJA1105 firmware over SPI 5:0 > No matching device ID found for devid FFFFFFFF, cs 0. > Error SJA1105 configuration not completed > Net: EQOS phy: rgmii @ 4 > > Warning: eth_eqos (eth0) using random MAC address - f6:65:86:a2:0e:f8 > eth0: eth_eqos PFE: emac0: sgmii emac1: none emac2: none > > Warning: eth_pfeng using MAC address from ROM > , eth1: eth_pfeng > Hit any key to stop autoboot: 0 > PFE: emac0: sgmii emac1: none emac2: none > PFE: emac0: sgmii emac1: none emac2: none > 1039 bytes read in 9 ms (112.3 KiB/s) > ## Executing script at 80200000 > 1048688 bytes read in 36 ms (27.8 MiB/s) > 14034952 bytes read in 201 ms (66.6 MiB/s) > 38461 bytes read in 9 ms (4.1 MiB/s) > ## Flattened Device Tree blob at 86600000 > Booting using the fdt blob at 0x86600000 > Using Device Tree in place at 0000000086600000, end 000000008660dfff > DT: Enabling PFE > DT: Enabling PFE_EMAC_0 > DT: pfe0 set to 00:01:be:be:ef:11 > DT: Disabling PFE_EMAC_1 > DT: Disabling PFE_EMAC_2 > > Starting kernel ... > > - UART enabled - > - Boot CPU booting - > - Current EL 00000008 - > - Initialize CPU - > - Turning on paging - > - Zero BSS - > - Ready - > (XEN) Checking for initrd in /chosen > (XEN) RAM: 0000000080000000 - 00000000ffffffff > (XEN) RAM: 0000000880000000 - 00000008dfffffff > (XEN) > (XEN) MODULE[0]: 0000000085600000 - 00000000857430c8 Xen > (XEN) MODULE[1]: 0000000086600000 - 000000008660a000 Device Tree > (XEN) MODULE[2]: 0000000085800000 - 0000000086562808 Kernel > (XEN) RESVD[0]: 00000000ff800000 - 00000000ff9fffff > (XEN) RESVD[1]: 00000000c0000000 - 00000000c03fffff > (XEN) RESVD[2]: 00000000c0400000 - 00000000c07fffff > (XEN) RESVD[3]: 00000000d0000000 - 00000000d03fffff > (XEN) RESVD[4]: 0000000084000000 - 000000008407ffff > (XEN) RESVD[5]: 0000000034000000 - 000000003407ffff > (XEN) RESVD[6]: 0000000034080000 - 000000003409ffff > (XEN) RESVD[7]: 0000000083200000 - 00000000835dffff > (XEN) RESVD[8]: 00000000835e0000 - 00000000835fffff > (XEN) > (XEN) > (XEN) Command line: dom0_mem=512M dom0_max_vcpus=1 bootscrub=0 > (XEN) PFN compression on bits 20...22 > (XEN) Domain heap initialised > (XEN) Booting using Device Tree > (XEN) Platform: NXP S32-Gen1 > (XEN) No dtuart path configured > (XEN) Bad console= option 'dtuart' > Xen 4.14.0 > (XEN) Xen version 4.14.0 (xen-4.14-r0@fsl-auto) (aarch64-fsl-linux-gcc (GCC) > 10. > 2.0) debug=y 2022-05-18 > (XEN) Latest ChangeSet: Wed May 18 15:47:26 2022 +0300 git:becdd18e50-dirty > (XEN) build-id: c93be820bfe87b5abccd95ea86e98121e1231249 > (XEN) Processor: 410fd034: "ARM Limited", variant: 0x0, part 0xd03, rev 0x4 > (XEN) 64-bit Execution: > (XEN) Processor Features: 0000000001002222 0000000000000000 > (XEN) Exception Levels: EL3:64+32 EL2:64+32 EL1:64+32 EL0:64+32 > (XEN) Extensions: FloatingPoint AdvancedSIMD GICv3-SysReg > (XEN) Debug Features: 0000000010305106 0000000000000000 > (XEN) Auxiliary Features: 0000000000000000 0000000000000000 > (XEN) Memory Model Features: 0000000000001122 0000000000000000 > (XEN) ISA Features: 0000000000011120 0000000000000000 > (XEN) 32-bit Execution: > (XEN) Processor Features: 00000131:10011011 > (XEN) Instruction Sets: AArch32 A32 Thumb Thumb-2 Jazelle > (XEN) Extensions: GenericTimer Security > (XEN) Debug Features: 03010066 > (XEN) Auxiliary Features: 00000000 > (XEN) Memory Model Features: 10201105 40000000 01260000 02102211 > (XEN) ISA Features: 02101110 13112111 21232042 01112131 00011142 00011121 > (XEN) Using SMC Calling Convention v1.2 > (XEN) Using PSCI v1.1 > (XEN) SMP: Allowing 8 CPUs > (XEN) enabled workaround for: ARM erratum 1530924 > (XEN) Generic Timer IRQ: phys=30 hyp=26 virt=27 Freq: 5000 KHz > (XEN) GICv3 initialization: > (XEN) gic_dist_addr=0x00000050800000 > (XEN) gic_maintenance_irq=25 > (XEN) gic_rdist_stride=0 > (XEN) gic_rdist_regions=1 > (XEN) redistributor regions: > (XEN) - region 0: 0x00000050900000 - 0x00000050b00000 > (XEN) GICv3 compatible with GICv2 cbase 0x00000050400000 vbase > 0x00000050420000 > (XEN) GICv3: 576 lines, (IID 0001143b). > (XEN) GICv3: CPU0: Found redistributor in region 0 @000000004001a000 > (XEN) XSM Framework v1.0.0 initialized > (XEN) Initialising XSM SILO mode > (XEN) Using scheduler: SMP Credit Scheduler rev2 (credit2) > (XEN) Initializing Credit2 scheduler > (XEN) load_precision_shift: 18 > (XEN) load_window_shift: 30 > (XEN) underload_balance_tolerance: 0 > (XEN) overload_balance_tolerance: -3 > (XEN) runqueues arrangement: socket > (XEN) cap enforcement granularity: 10ms > (XEN) load tracking window length 1073741824 ns > (XEN) Allocated console ring of 64 KiB. > (XEN) CPU0: Guest atomics will try 13 times before pausing the domain > (XEN) Bringing up CPU1 > - CPU 00000001 booting - > - Current EL 00000008 - > - Initialize CPU - > - Turning on paging - > - Ready - > (XEN) GICv3: CPU1: Found redistributor in region 0 @000000004003a000 > (XEN) CPU1: Guest atomics will try 15 times before pausing the domain > (XEN) CPU 1 booted. > (XEN) Bringing up CPU2 > - CPU 00000100 booting - > - Current EL 00000008 - > - Initialize CPU - > - Turning on paging - > - Ready - > (XEN) GICv3: CPU2: Found redistributor in region 0 @000000004009a000 > (XEN) CPU2: Guest atomics will try 15 times before pausing the domain > (XEN) CPU 2 booted. > (XEN) Bringing up CPU3 > - CPU 00000101 booting - > - Current EL 00000008 - > - Initialize CPU - > - Turning on paging - > - Ready - > (XEN) GICv3: CPU3: Found redistributor in region 0 @00000000400ba000 > (XEN) CPU3: Guest atomics will try 15 times before pausing the domain > (XEN) CPU 3 booted. > (XEN) Bringing up CPU4 > - CPU 00000002 booting - > - Current EL 00000008 - > - Initialize CPU - > - Turning on paging - > - Ready - > (XEN) GICv3: CPU4: Found redistributor in region 0 @000000004005a000 > (XEN) CPU4: Guest atomics will try 14 times before pausing the domain > (XEN) CPU 4 booted. > (XEN) Bringing up CPU5 > - CPU 00000003 booting - > - Current EL 00000008 - > - Initialize CPU - > - Turning on paging - > - Ready - > (XEN) GICv3: CPU5: Found redistributor in region 0 @000000004007a000 > (XEN) CPU5: Guest atomics will try 15 times before pausing the domain > (XEN) CPU 5 booted. > (XEN) Bringing up CPU6 > - CPU 00000102 booting - > - Current EL 00000008 - > - Initialize CPU - > - Turning on paging - > - Ready - > (XEN) GICv3: CPU6: Found redistributor in region 0 @00000000400da000 > (XEN) CPU6: Guest atomics will try 16 times before pausing the domain > (XEN) CPU 6 booted. > (XEN) Bringing up CPU7 > - CPU 00000103 booting - > - Current EL 00000008 - > - Initialize CPU - > - Turning on paging - > - Ready - > (XEN) GICv3: CPU7: Found redistributor in region 0 @00000000400fa000 > (XEN) CPU7: Guest atomics will try 15 times before pausing the domain > (XEN) CPU 7 booted. > (XEN) Brought up 8 CPUs > (XEN) I/O virtualisation disabled > (XEN) P2M: 40-bit IPA with 40-bit PA and 8-bit VMID > (XEN) P2M: 3 levels with order-1 root, VTCR 0x80023558 > (XEN) Scheduling granularity: cpu, 1 CPU per sched-resource > (XEN) Adding cpu 0 to runqueue 0 > (XEN) First cpu on runqueue, activating > (XEN) Adding cpu 1 to runqueue 0 > (XEN) Adding cpu 2 to runqueue 0 > (XEN) Adding cpu 3 to runqueue 0 > (XEN) Adding cpu 4 to runqueue 0 > (XEN) Adding cpu 5 to runqueue 0 > (XEN) Adding cpu 6 to runqueue 0 > (XEN) Adding cpu 7 to runqueue 0 > (XEN) alternatives: Patching with alt table 00000000002d4308 -> > 00000000002d4b3c > (XEN) *** LOADING DOMAIN 0 *** > (XEN) Loading d0 kernel from boot module @ 0000000085800000 > (XEN) Allocating 1:1 mappings totalling 512MB for dom0: > (XEN) BANK[0] 0x000000a0000000-0x000000c0000000 (512MB) > (XEN) Grant table range: 0x00000085600000-0x00000085640000 > (XEN) Allocating PPI 16 for event channel interrupt > (XEN) Loading zImage from 0000000085800000 to > 00000000a0000000-00000000a0d62808 > (XEN) Loading d0 DTB to 0x00000000a8000000-0x00000000a800947a > (XEN) Initial low memory virq threshold set at 0x4000 pages. > (XEN) Std. Loglevel: All > (XEN) Guest Loglevel: All > (XEN) *** Serial input to DOM0 (type 'CTRL-a' three times to switch input) > (XEN) Freed 352kB init memory. > (XEN) d0v0: vGICD: RAZ on reserved register offset 0x00000c > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER4 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER8 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER12 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER16 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER20 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER24 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER28 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER32 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER36 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER40 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER44 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER48 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER52 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER56 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER60 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER64 > (XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER68 > (XEN) d0v0: vGICR: SGI: unhandled word write 0x000000ffffffff to ICACTIVER0 > [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] > [ 0.000000] Linux version 5.10.109-rt65+g0bace7fde5f5 (oe-user@oe-host) > (aarc > h64-fsl-linux-gcc (GCC) > 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP PREEMPT Fri > > Jun 24 15:01:08 UTC 2022 > [ 0.000000] Machine model: NXP S32G3XXX-EVB3 > [ 0.000000] Xen 4.14 support found > [ 0.000000] Reserved memory: created DMA memory pool at > 0x0000000083200000, s > ize 3 > MiB > [ 0.000000] OF: reserved mem: initialized node pfebufs@83200000, > compatible i > d shared-dma-pool > [ 0.000000] Zone ranges: > [ 0.000000] DMA [mem 0x0000000034000000-0x00000000ff9fffff] > [ 0.000000] DMA32 empty > [ 0.000000] Normal empty > [ 0.000000] Movable zone start for each node > [ 0.000000] Early memory node ranges > [ 0.000000] node 0: [mem 0x0000000034000000-0x000000003409ffff] > [ 0.000000] node 0: [mem 0x0000000083200000-0x00000000835dffff] > [ 0.000000] node 0: [mem 0x00000000835e0000-0x00000000835fffff] > [ 0.000000] node 0: [mem 0x0000000084000000-0x000000008407ffff] > [ 0.000000] node 0: [mem 0x00000000a0000000-0x00000000bfffffff] > [ 0.000000] node 0: [mem 0x00000000c0000000-0x00000000c07fffff] > [ 0.000000] node 0: [mem 0x00000000d0000000-0x00000000d03fffff] > [ 0.000000] node 0: [mem 0x00000000ff800000-0x00000000ff9fffff] > [ 0.000000] Initmem setup node 0 [mem > 0x0000000034000000-0x00000000ff9fffff] > [ 0.000000] cma: Reserved 256 MiB at 0x00000000ad000000 > [ 0.000000] psci: probing for conduit method from DT. > [ 0.000000] psci: PSCIv1.1 detected in firmware. > [ 0.000000] psci: Using standard PSCI v0.2 function IDs > [ 0.000000] psci: Trusted OS migration not required > [ 0.000000] psci: SMC Calling Convention v1.1 > [ 0.000000] percpu: Embedded 17 pages/cpu s32024 r8192 d29416 u69632 > [ 0.000000] Detected VIPT I-cache on CPU0 > [ 0.000000] CPU features: detected: ARM erratum 845719 > [ 0.000000] CPU features: detected: GIC system register CPU interface > [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, 1530923, > or > 1530924 > [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 134109 > [ 0.000000] Kernel command line: console=ttyLF0,115200 earlycon=xen > earlyprin > tk=xen > root=/dev/mmcblk0p2 rw clk_ignore_unused > [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 > bytes, > linear) > [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, > li > near) > [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off > [ 0.000000] Memory: 202252K/543872K available (8766K kernel code, 650K > rwdata > , 2880K rodata, 1344K > init, 245K bss, 79476K reserved, 262144K cma-reserved) > [ 0.000000] rcu: Preemptible hierarchical RCU implementation. > [ 0.000000] rcu: RCU event tracing is enabled. > [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1. > [ 0.000000] Trampoline variant of Tasks RCU enabled. > [ 0.000000] Tracing variant of Tasks RCU enabled. > [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 > jif > fies. > [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 > [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 > [ 0.000000] GICv3: 544 SPIs implemented > [ 0.000000] GICv3: 0 Extended SPIs implemented > [ 0.000000] GICv3: Distributor has no Range Selector support > [ 0.000000] GICv3: 16 PPIs implemented > [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000050900000 > [ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x4ec > wit > h crng_init=0 > [ 0.000000] arch_timer: cp15 timer(s) running at 5.00MHz (virt). > [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff > max_cycles: > 0x127350b88, > max_idle_ns: 440795202120 ns > [ 0.000001] sched_clock: 56 bits at 5MHz, resolution 200ns, wraps every > 43980 > 46511100ns > [ 0.000357] Console: colour dummy device 80x25 > [ 0.000385] Calibrating delay loop (skipped), value calculated using timer > fr > equency.. 10.00 BogoMIPS > (lpj=20000) > [ 0.000395] pid_max: default: 32768 minimum: 301 > [ 0.000489] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, > line > ar) > [ 0.000500] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 > bytes, > linear) > [ 0.001943] xen:grant_table: Grant tables using version 1 layout > [ 0.001964] Grant table initialized > [ 0.001994] xen:events: Using FIFO-based ABI > [ 0.002023] Xen: initializing cpu0 > [ 0.002127] rcu: Hierarchical SRCU implementation. > [ 0.002412] smp: Bringing up secondary CPUs ... > [ 0.002415] smp: Brought up 1 node, 1 CPU > [ 0.002419] SMP: Total of 1 processors activated. > [ 0.002427] CPU features: detected: 32-bit EL0 Support > [ 0.002433] CPU features: detected: CRC32 instructions > [ 0.009718] CPU: All CPU(s) started at EL1 > [ 0.009731] alternatives: patching kernel code > [ 0.010183] devtmpfs: initialized > [ 0.014415] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, > ma > x_idle_ns: > 7645041785100000 ns > [ 0.014429] futex hash table entries: 256 (order: 2, 16384 bytes, linear) > [ 0.020426] pinctrl core: initialized pinctrl subsystem > [ 0.020983] NET: Registered protocol family 16 > [ 0.022141] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic > allocations > [ 0.022218] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic > allo > cations > [ 0.022309] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic > al > locations > [ 0.022851] thermal_sys: Registered thermal governor 'step_wise' > [ 0.023110] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. > [ 0.023153] ASID allocator initialised with 65536 entries > [ 0.023218] xen:swiotlb_xen: Warning: only able to allocate 4 MB for > software > IO TLB > [ 0.023933] software IO TLB: mapped [mem > 0x00000000a1800000-0x00000000a1c0000 > > 0] (4MB) > [ 0.023998] Serial: AMBA PL011 UART driver > [ 0.024571] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled. > [ 0.024649] arm-scmi firmware:scmi: No. of Protocol > MAX_PROTOCOLS_IMP > [ 0.024654] arm-scmi firmware:scmi: SCMI Protocol v2.0 'NXP:S32G399A' > Firmwar > e version 0x0 > [ 0.039850] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages > [ 0.039858] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages > [ 0.039862] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages > [ 0.039866] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages > [ 0.043412] scmi-clocks scmi_dev.1: failed to register clock 87 > [ 0.043421] scmi-clocks scmi_dev.1: failed to register clock 88 > [ 0.043428] scmi-clocks scmi_dev.1: failed to register clock 89 > [ 0.043434] scmi-clocks scmi_dev.1: failed to register clock 90 > [ 0.043507] scmi-clocks scmi_dev.1: failed to register clock 95 > [ 0.043514] scmi-clocks scmi_dev.1: failed to register clock 96 > [ 0.043520] scmi-clocks scmi_dev.1: failed to register clock 97 > [ 0.043526] scmi-clocks scmi_dev.1: failed to register clock 98 > [ 0.046871] xen:balloon: Initialising balloon driver > [ 0.047230] vgaarb: loaded > [ 0.047367] SCSI subsystem initialized > [ 0.047494] usbcore: registered new interface driver usbfs > [ 0.047521] usbcore: registered new interface driver hub > [ 0.047541] usbcore: registered new device driver usb > [ 0.047818] pps_core: LinuxPPS API ver. 1 registered > [ 0.047821] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo > Giome > tti <giometti@xxxxxxxx> > [ 0.047831] PTP clock support registered > [ 0.048664] clocksource: Switched to clocksource arch_sys_counter > [ 0.053083] NET: Registered protocol family 2 > [ 0.053173] IP idents hash table entries: 16384 (order: 5, 131072 bytes, > line > ar) > [ 0.053762] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, > 8192 > bytes, linear) > [ 0.053787] TCP established hash table entries: 8192 (order: 4, 65536 > bytes, > linear) > [ 0.053847] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, > linear > ) > [ 0.053970] TCP: Hash tables configured (established 8192 bind 8192) > [ 0.054028] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) > [ 0.054052] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, > linear) > [ 0.054147] NET: Registered protocol family 1 > [ 0.054435] RPC: Registered named UNIX socket transport module. > [ 0.054439] RPC: Registered udp transport module. > [ 0.054441] RPC: Registered tcp transport module. > [ 0.054443] RPC: Registered tcp NFSv4.1 backchannel transport module. > [ 0.054451] PCI: CLS 0 bytes, default 64 > [ 0.055375] workingset: timestamp_bits=62 max_order=17 bucket_order=0 > [ 0.055858] fuse: init (API version 7.32) > [ 0.055965] NET: Registered protocol family 38 > [ 0.055988] Block layer SCSI generic (bsg) driver version 0.4 loaded > (major 2 > 48) > [ 0.055993] io scheduler mq-deadline registered > [ 0.055997] io scheduler kyber registered > [ 0.057025] s32g-siul2-pinctrl 4009c240.siul2-pinctrl: initialized s32 > pinctr > l driver > [ 0.057965] gpio-339 (llcecan0-en): hogged as output/high > [ 0.057983] gpio-340 (llcecan0-stby): hogged as output/high > [ 0.057998] gpio-342 (llcecan4-en): hogged as output/high > [ 0.058014] gpio-343 (llcecan4-stby): hogged as output/high > [ 0.058029] gpio-345 (llcecan5-en): hogged as output/high > [ 0.058044] gpio-346 (llcecan5-stby): hogged as output/high > [ 0.058058] gpio-351 (llcecan6-en): hogged as output/high > [ 0.058072] gpio-352 (llcecan6-stby): hogged as output/high > [ 0.058089] gpio-353 (llcecan12-stby): hogged as output/high > [ 0.058103] gpio-358 (llcecan12-en): hogged as output/high > [ 0.058120] gpio-360 (llcecan13-en): hogged as output/high > [ 0.058135] gpio-361 (llcecan13-stby): hogged as output/high > [ 0.058151] gpio-382 (llcecan15-en): hogged as output/high > [ 0.058165] gpio-383 (llcecan15-stby): hogged as output/high > [ 0.059358] xen:xen_evtchn: Event-channel device installed > [ 0.060467] serial: Freescale linflex driver > [ 0.060686] 401c8000.serial: ttyLF0 at MMIO 0x401c8000 (irq = 25, > base_baud = > 7812500) is a > FSL_LINFLEX > [ 0.060735] printk: console [ttyLF0] enabled > [ 0.061072] 401cc000.serial: ttyLF1 at MMIO 0x401cc000 (irq = 26, > base_baud = > 7812500) is a > FSL_LINFLEX > [ 0.061385] 402bc000.serial: ttyLF2 at MMIO 0x402bc000 (irq = 44, > base_baud = > 7812500) is a > FSL_LINFLEX > [ 0.061832] cacheinfo: Unable to detect cache hierarchy for CPU 0 > [ 0.061846] Invalid max_queues (4), will use default max: 1. > [ 0.062193] fsl_fccu 4030c000.fccu: FCCU status is 0 (normal) > [ 0.063813] spi-nor spi0.0: mt35xu02g (262144 Kbytes) > [ 0.065365] vcan: Virtual CAN interface driver > [ 0.065370] slcan: serial line CAN interface driver > [ 0.065372] slcan: 10 dynamic interface channels. > [ 0.065377] CAN device driver interface > [ 0.065555] e100: Intel(R) PRO/100 Network Driver > [ 0.065558] e100: Copyright(c) 1999-2006 Intel Corporation > [ 0.065585] e1000: Intel(R) PRO/1000 Network Driver > [ 0.065588] e1000: Copyright (c) 1999-2006 Intel Corporation. > [ 0.065615] e1000e: Intel(R) PRO/1000 Network Driver > [ 0.065616] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. > [ 0.065642] igb: Intel(R) Gigabit Ethernet Network Driver > [ 0.065645] igb: Copyright (c) 2007-2014 Intel Corporation. > [ 0.065920] xen_netfront: Initialising Xen virtual ethernet driver > [ 0.066016] hse-uio 40211000.mu1b: firmware not found > [ 0.066208] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > [ 0.066213] ehci-pci: EHCI PCI platform driver > [ 0.066318] usbcore: registered new interface driver uas > [ 0.066346] usbcore: registered new interface driver usb-storage > [ 0.067503] s32gen1-rtc 40060000.rtc: registered as rtc0 > [ 0.067533] s32gen1-rtc 40060000.rtc: setting system clock to > 1970-01-01T00:0 > 0:00 UTC (0) > [ 0.067665] i2c /dev entries driver > [ 0.068026] sac58r-wdt 4010c000.swt: SAC58R/S32GEN1 Watchdog Timer > Registered > . timeout=30s > (nowayout=0) > [ 0.068204] sac58r-wdt 40200000.swt: SAC58R/S32GEN1 Watchdog Timer > Registered > . timeout=30s > (nowayout=0) > [ 0.068371] sac58r-wdt 40204000.swt: SAC58R/S32GEN1 Watchdog Timer > Registered > . timeout=30s > (nowayout=0) > [ 0.068538] sac58r-wdt 40208000.swt: SAC58R/S32GEN1 Watchdog Timer > Registered > . timeout=30s > (nowayout=0) > [ 0.068776] sac58r-wdt 40500000.swt: SAC58R/S32GEN1 Watchdog Timer > Registered > . timeout=30s > (nowayout=0) > [ 0.068950] sac58r-wdt 40504000.swt: SAC58R/S32GEN1 Watchdog Timer > Registered > . timeout=30s > (nowayout=0) > [ 0.069112] sac58r-wdt 40508000.swt: SAC58R/S32GEN1 Watchdog Timer > Registered > . timeout=30s > (nowayout=0) > [ 0.069279] sac58r-wdt 4050c000.swt: SAC58R/S32GEN1 Watchdog Timer > Registered > . timeout=30s > (nowayout=0) > [ 0.069492] sdhci: Secure Digital Host Controller Interface driver > [ 0.069495] sdhci: Copyright(c) Pierre Ossman > [ 0.069497] sdhci-pltfm: SDHCI platform and OF driver helper > [ 0.069837] mmc0: CQHCI version 5.10 > [ 0.070452] hse 40210000.mu0b: firmware not found > [ 0.070658] usbcore: registered new interface driver usbhid > [ 0.070662] usbhid: USB HID core driver > [ 0.082993] s32-adc 401f8000.adc: Device initialized successfully. > [ 0.094947] s32-adc 402e8000.adc: Device initialized successfully. > [ 0.095109] nxp_s32_ddr_perf 403e0000.ddr-perf: probing device > [ 0.095353] nxp_s32_ddr_perf 403e0000.ddr-perf: device initialized > successful > ly > [ 0.095430] s32-siul2-nvmem 4009c000.nvram: initialize s32 siul2 nvmem > driver > [ 0.095550] s32-siul2-nvmem 44010000.nvram: initialize s32 siul2 nvmem > driver > [ 0.095949] NET: Registered protocol family 10 > [ 0.096436] Segment Routing with IPv6 > [ 0.096476] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver > [ 0.096852] NET: Registered protocol family 17 > [ 0.096947] can: controller area network core > [ 0.096980] NET: Registered protocol family 29 > [ 0.096984] can: raw protocol > [ 0.096989] can: broadcast manager protocol > [ 0.096996] can: netlink gateway - max_hops=1 > [ 0.097014] 8021q: 802.1Q VLAN Support v1.8 > [ 0.097149] printk: console [ttyLF0]: printing thread started > [ 0.100703] mmc0: SDHCI controller on 402f0000.usdhc [402f0000.usdhc] > using A > DMA > [ 0.108674] phy-s32gen1-serdes 40480000.serdes: Using mode 0 for SerDes > subsy > stem > [ 0.109020] phy-s32gen1-serdes 44180000.serdes: Using mode 3 for SerDes > subsy > stem > [ 0.115131] phy-s32gen1-serdes 44180000.serdes: Unstable RX detected on > XPCS1 > [ 0.115158] phy-s32gen1-serdes 44180000.serdes: Unstable RX detected on > XPCS0 > [ 0.115337] s32gen1-pcie 40400000.pcie: Configured as RootComplex > [ 0.115627] s32gen1-pcie 40400000.pcie: Setting PCI Device and Vendor IDs > to > 0x4300:0x1957 > [ 0.116614] s32gen1-pcie 40400000.pcie: Allocated line 0 for interrupt 52 > (ms > i) > [ 0.383316] mmc0: Command Queue Engine enabled > [ 0.383326] mmc0: new DDR MMC card at address 0001 > [ 0.391409] mmcblk0: mmc0:0001 G1M15M 59.3 GiB > [ 0.391539] mmcblk0boot0: mmc0:0001 G1M15M partition 1 31.5 MiB > [ 0.391661] mmcblk0boot1: mmc0:0001 G1M15M partition 2 31.5 MiB > [ 0.391804] mmcblk0rpmb: mmc0:0001 G1M15M partition 3 4.00 MiB, chardev > (243: > 0) > [ 0.399208] mmcblk0: p1 p2 p3 > [ 1.136116] s32gen1-pcie 40400000.pcie: Failed to stabilize PHY link > [ 1.136123] s32gen1-pcie 40400000.pcie: Configuring as RootComplex > [ 1.136136] s32gen1-pcie 40400000.pcie: host bridge /soc/pcie@40400000 > ranges > : > [ 1.136177] s32gen1-pcie 40400000.pcie: IO > 0x5ffffe0000..0x5ffffeffff - > > > 0x0000000000 > [ 1.136195] s32gen1-pcie 40400000.pcie: MEM > 0x5800000000..0x5ffffdffff - > > > 0x0000000000 > (XEN) physdev.c:16:d0v0 PHYSDEVOP cmd=25: not implemented > [ 2.142041] s32gen1-pcie 40400000.pcie: Phy link never came up > (XEN) physdev.c:16:d0v0 PHYSDEVOP cmd=15: not implemented > [ 2.142133] s32gen1-pcie 40400000.pcie: PCI host bridge to bus 0000:00 > [ 2.142139] pci_bus 0000:00: root bus resource [bus 00-ff] > [ 2.142147] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] > [ 2.142153] pci_bus 0000:00: root bus resource [mem > 0x5800000000-0x5ffffdffff > ] > (bus address [0x00000000-0x7fffdffff]) > [ 2.142201] pci 0000:00:00.0: [16c3:4300] type 01 class 0x060400 > [ 2.142224] pci 0000:00:00.0: reg 0x10: [mem 0x5800000000-0x58000fffff] > [ 2.142242] pci 0000:00:00.0: reg 0x38: [mem 0x5800000000-0x580000ffff > pref] > [ 2.142339] pci 0000:00:00.0: supports D1 > [ 2.142344] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold > [ 2.165526] pci 0000:00:00.0: Failed to add - passthrough or MSI/MSI-X > might > fail! > [ 2.168521] pci 0000:00:00.0: BAR 0: assigned [mem > 0x5800000000-0x58000fffff] > [ 2.168532] pci 0000:00:00.0: BAR 6: assigned [mem > 0x5800100000-0x580010ffff > > pref] > [ 2.168541] pci 0000:00:00.0: PCI bridge to [bus 01-ff] > [ 2.168839] pcieport 0000:00:00.0: PME: Signaling with IRQ 67 > [ 2.175158] clk: Not disabling unused clocks > [ 2.270457] random: fast init done > [ 2.282422] EXT4-fs (mmcblk0p2): recovery complete > [ 2.283171] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data > mode. O > pts: (null) > [ 2.283229] VFS: Mounted root (ext4 filesystem) on device 179:2. > [ 2.283571] devtmpfs: mounted > [ 2.284179] Freeing unused kernel memory: 1344K > [ 2.284312] Run /sbin/init as init process > [ 2.413488] systemd[1]: System time before build time, advancing clock. > [ 2.441298] systemd[1]: systemd 246 running in system mode. (+PAM -AUDIT > -SEL > INUX +IMA -APPARMOR > -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL + > > XZ -LZ4 -ZSTD -SECCOMP +BLKID -ELFUTILS +KMOD > -IDN2 -IDN -PCRE2 default-hierarch > > y=hybrid) > > W[ 2.442307] systemd[1]: Detected architecture arm64. > elcome to Auto Linux BSP 33.0 (gatesgarth)! > > [ 2.484975] systemd[1]: Set hostname to <s32g399aevb3>. > [ 2.577683] systemd-sysv-generator[76]: SysV service '/etc/init.d/netperf' > la > cks a native systemd unit > file. Automatically generating a unit file for compati > > bility. Please update package to include a native > systemd unit file, in order to > > make it more safe and robust. > [ 2.766744] systemd[1]: > /lib/systemd/system/xen-qemu-dom0-disk-backend.servic > > e:11: PIDFile= references a path below legacy > directory /var/run/, updating /var > > /run/xen/qemu-dom0.pid → /run/xen/qemu-dom0.pid; please update the unit > file acc > ordingly. > [ OK [ 2.849603] systemd[1]: Queued start job for default target > Multi-User > System. > random: systemd: uninitialized urandom read (16 bytes read) > [[ 2.851615] systemd[1]: Created slice system-getty.slice. > 0m] Created slice system-getty.slice. > [ OK ] Created slice sy[ 2.884743] random: systemd: uninitialized > urandom r > ead (16 bytes read) > s[ 2.885064] systemd[1]: Created slice system-modprobe.slice. > tem-modprobe.slice. > [ OK ] Created slice sys[ 2.912705] random: systemd: uninitialized > urandom > read (16 bytes read) > t[ 2.913002] systemd[1]: Created slice system-serial\x2dgetty.slice. > em-serial\x2dgetty.slice. > [ OK ] Created slice Use[ 2.940962] systemd[1]: Created slice User and > Sess > ion Slice. > r and Session Slice. > [ OK ] Started Dispatch P[ 2.960876] systemd[1]: Started Dispatch > Password > Requests to Console > Directory Watch. > assword …ts to Console Directory Watch. > [ OK ] Started Forward Pas[ 2.988824] systemd[1]: Started Forward > Password > Requests to Wall > Directory Watch. > sword R…uests to Wall Directory Watch. > [ OK ] Reached target Path[ 3.012877] systemd[1]: Reached target Paths. > s. > [ OK ] Reached target Remot[ 3.032754] systemd[1]: Reached target Remote > Fi > le Systems. > e File Systems. > [ OK ] Reached target Slice[ 3.052744] systemd[1]: Reached target Slices. > s. > [ OK ] Reached target Swap systemd[1]: Reached target Swap. > [0m. > [ OK systemd[1]: Listening on RPCbind Server Activation Socket. > [0m] Listening on RPCbind Server Activation Socket. > [ OK ] Reached target RPC [ 3.124844] systemd[1]: Reached target RPC > Port M > apper. > Port Mapper. > [ OK ] Listening on Sy[ 3.145153] systemd[1]: Listening on Syslog Socket. > slog Socket. > [ OK ] Listening on initc[ 3.164886] systemd[1]: Listening on initctl > Compa > tibility Named Pipe. > tl Compatibility Named Pipe. > [ OK 3.191035] systemd[1]: Condition check resulted in Journal Audit > Socke > t being skipped. > m[ 3.191496] systemd[1]: Listening on Journal Socket (/dev/log). > ] Listening on Journal Socket (/dev/log). > [ OK ] Listening on Jou[ 3.221106] systemd[1]: Listening on Journal > Socket. > rnal Socket. > [ OK ] Listening on Ne[ 3.241190] systemd[1]: Listening on Network > Service > Netlink Socket. > twork Service Netlink Socket. > [ OK ] Listening on ude[ 3.265051] systemd[1]: Listening on udev Control > So > cket. > v Control Socket. > [ OK ] Listening on udev [ 3.284919] systemd[1]: Listening on udev > Kernel S > ocket. > Kernel Socket. > [ OK ] Listening on User [ 3.304936] systemd[1]: Listening on User > Database > Manager Socket. > Database Manager Socket. > Mounting H[ 3.330591] systemd[1]: Mounting Huge Pages File > System... > uge Pages File System... > Mounting 3.353156] systemd[1]: Condition check resulted in POSIX > Me > ssage Queue File System > being skipped. > ;39mMount /proc/xen files... > [ 3.354954] systemd[1]: Mounting Mount /proc/xen files... > [ 3.370933] systemd[1]: Mounting Kernel Debug File System... > Mounting Kernel Debug File System... > Starti[ 3.401191] systemd[1]: Condition check resulted in Kernel > Tra > ce File System being > skipped. > ng Load Kernel Module con[ 3.401679] systemd[1]: Condition check resulted > in > Create list of static > device nodes for the current kernel being skipped. > fi[ 3.403642] systemd[1]: Starting Load Kernel Module configfs... > gfs... > Starting 3.446771] systemd[1]: Starting Load Kernel Module drm... > 9mLoad Kernel Module drm... > Starting 3.470771] systemd[1]: Starting Load Kernel Module > fuse... > 9mLoad Kernel Module fuse... > Starting 3.494788] systemd[1]: Starting RPC Bind... > 9mRPC Bind... > [ 3.513000] systemd[1]: Condition check resulted in File System Check > on > Root Device being skipped. > Starting Jour[ 3.516455] systemd[1]: Starting Journal Service... > nal Service... > [ 3.548101] systemd[1]: Starting Load Kernel Modules... > Starting Load Kernel Modules... > Starting 3.570819] systemd[1]: Starting Remount Root and Kernel > Fil > e Systems... > 9mRemount Root and Kernel File Systems... > [ 3.595018] systemd[1]: Starting Coldplug All udev Devices... > Starting Coldplug All udev Devices... > [ 3.632457] llce_core 43ff8000.llce: Successfully loaded LLCE firmware > [ 3.639641] systemd[1]: Started RPC Bind. > 32m OK ] Started RPC Bind. > [ 3.651233] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) > [ 3.706544] systemd[1]: Mounted Huge Pages File System. > 32m OK ] Mounted Huge Pages File System. > [ 3.729184] systemd[1]: Mounted Mount /proc/xen files. > 32m OK ] Mounted Mount /proc/xen files. > [ OK ] Started Journa[ 3.749158] systemd[1]: Started Journal Service. > l Service. > [ OK ] Mounted Kernel Debug File System. > [ OK ] Finished Load Kernel Module configfs. > [ OK ] Finished Load Kernel Module drm. > [ 3.804694] llce_mb 43a00000.llce_mb: LLCE firmware version: GGEE_3A > [ 3.804711] llce_mb 43a00000.llce_mb: LLCE firmware: logging support > disabled > [ OK ] Finished Load Kernel Module fuse. > [ OK ] Finished Remount Root and Kernel File Systems. > Mounting FUSE Control File System... > Mounting Kernel Configuration File System... > [ 3.916363] llce_can: unknown parameter 'logging' ignored > Starting Flush Journal to Persistent Storage... > Starting Create Static Device Nodes in /dev... > [ OK ] Mounted FUSE Control File System. > [ OK ] Finished Load Kernel Modules. > [ OK ] Mounted Kernel Configuration File System. > [ OK ] Finished Flush Journal to Persistent Storage. > [ OK ] Finished Create Static Device Nodes in /dev. > [ OK ] Reached target Local File Systems (Pre). > Mounting NFSD configuration filesystem... > Mounting /tmp... > Mounting mount xenstore file system... > Mounting /var/volatile... > Starting Apply Kernel Variables... > Starting Rule-based Manage…for Device Events and Files... > [ OK ] Finished Coldplug All udev Devices. > [FAILED] Failed to mount NFSD configuration filesystem. > See 'systemctl status proc-fs-nfsd.mount' for details. > [DEPEND] Dependency failed for NFS server and services. > [DEPEND] Dependency failed for NFS Mount Daemon. > [ OK ] Started Rule-based Manager for Device Events and Files. > [ OK ] Mounted /tmp. > [ OK ] Mounted mount xenstore file system. > [ OK ] Mounted /var/volatile. > [ OK ] Finished Apply Kernel Variables. > Mounting /var/volatile/tmp... > Starting Load/Save Random Seed... > [ OK ] Mounted /var/volatile/tmp. > [ OK ] Reached target Local File Systems. > Starting Create Volatile Files and Directories... > [ OK ] Finished Create Volatile Files and Directories. > [ 5.060091] pfeng: loading out-of-tree module taints kernel. > [ 5.087732] pfeng 46000000.pfe: PFEng ethernet driver loading ... > [ 5.087749] pfeng 46000000.pfe: Version: RTM 1.0.0 > [ 5.087753] pfeng 46000000.pfe: Multi instance support: disabled > (standalone) > [ 5.087756] pfeng 46000000.pfe: Compiled by: 10.2.0 > [ 5.087783] pfeng 46000000.pfe: Cbus addr 0x46000000 size 0x1000000 > [ 5.087791] pfeng 46000000.pfe: nxp,fw-class-name: s32g_pfe_class.fw > [ 5.087796] pfeng 46000000.pfe: nxp,fw-util-name: s32g_pfe_util.fw > [ 5.087848] pfeng 46000000.pfe: irq 'hif0' : 58 > [ 5.087862] pfeng 46000000.pfe: irq 'hif1' : 59 > [ 5.087874] pfeng 46000000.pfe: irq 'hif2' : 60 > [ 5.087879] pfeng 46000000.pfe: HIF channels mask: 0x0007 > [ 5.087890] pfeng 46000000.pfe: netif name: pfe0 > [ 5.087896] pfeng 46000000.pfe: DT mac addr: 00:01:be:be:ef:11 > [ 5.087903] pfeng 46000000.pfe: netif(pfe0) mode: std > [ 5.087908] pfeng 46000000.pfe: netif(pfe0) EMAC: 0 > [ 5.087914] pfeng 46000000.pfe: netif(pfe0) HIFs: count 1 map 01 > [ 5.087923] pfeng 46000000.pfe: EMAC0 interface mode: 4 > [ 5.088060] pfeng 46000000.pfe: PFE port coherency enabled, mask 0x1e > [ 5.088249] pfeng 46000000.pfe: Clocks: sys=300MHz pe=600MHz > [ 5.088263] pfeng 46000000.pfe: Interface selected: EMAC0: 0x4 EMAC1: > 0xfffff > fff EMAC2: 0xffffffff > [ 5.120057] pfeng 46000000.pfe: PFE controller reset done > [ 5.120169] pfeng 46000000.pfe: TX clock on EMAC0 for interface sgmii > install > ed > [ 5.120219] pfeng 46000000.pfe: RX clock on EMAC0 for interface sgmii > install > ed > [ 5.120556] pfeng 46000000.pfe: assigned reserved memory node > pfebufs@3400000 > 0 > [ 5.129221] pfeng 46000000.pfe: assigned reserved memory node > pfebufs@34 > 080000 > Starting Network Time Synchronization... > [ 5.129320] pfeng 46000000.pfe: assigned reserved memory node > pfebufs@8320000 > 0 > [ 5.129353] pfeng 46000000.pfe: assigned reserved memory node > pfebufs@83 > 5e0000 > Starting Update UTMP about System Boot/Shutdown... > [ 5.137731] pfeng 46000000.pfe: Firmware: CLASS s32g_pfe_class.fw [39860 > byte > s] > [ 5.137746] pfeng 46000000.pfe: Firmware: UTIL s32g_pfe_util.fw [19940 > bytes] > 32m OK ] Finished Update UTMP about System Boot/Shutdown. > [ 5.137765] pfeng 46000000.pfe: PFE CBUS p0x46000000 mapped @ > v0xffffffc01300 > 0000 > [ 5.137781] pfeng 46000000.pfe: HW version 0x101 > [ 5.137788] pfeng 46000000.pfe: Silicon S32G3 > [ 5.137795] pfeng 46000000.pfe: Fail-Stop mode disabled > [ 5.139219] pfeng 46000000.pfe: BMU1 buffer base: p0xc0000000 > [ 5.139318] pfeng 46000000.pfe: BMU2 buffer base: p0x34000000 (0x80000 > bytes) > [ 5.140631] pfeng 46000000.pfe: register IRQ 62 by name 'PFE BMU IRQ' > [ 5.173797] pfeng 46000000.pfe: BMU_EMPTY_INT (BMU @ p0x(____ptrval____)). > Po > ol ready. > [ 5.173819] pfeng 46000000.pfe: BMU_EMPTY_INT (BMU @ p0x(____ptrval____)). > Po > ol ready. > [ 5.173857] pfeng 46000000.pfe: Firmware .elf detected > 32m OK ] Started Network Time Synchronization 5.173864] pfeng > 46000000.pfe: > Uploading > CLASS firmware > 0m. > [ 5.173871] pfeng 46000000.pfe: Selected FW loading OPs to load 8 PEs in > para > llel > [ 5.341346] pfeng 46000000.pfe: pfe_ct.h file > version"e1cb376b67fa4d1de800b13 > > 2b328b42c" > [ 5.383695] pfeng 46000000.pfe: [FW VERSION] 1.3.0, Build: May 31 2022, > 08:22 > :22 (), ID: 0x31454650 > [ 5.384015] pfeng 46000000.pfe: SAFETY instance created > 32m OK ] Reached target System Initialization 5.384025] pfeng > 46000000.pfe: > Watchdog > instance created > 0m. > [ 5.384038] pfeng 46000000.pfe: Uploading UTIL firmware > [ 5.384043] pfeng 46000000.pfe: Selected FW loading OPs to load 1 PEs in > para > llel > 32m OK ] Started Daily Cleanup of Temporary Directories. > [ 5.396834] pfeng 46000000.pfe: pfe_ct.h file > version"e1cb376b67fa4d1de800b13 > > 2b328b42c" > [ 5.410446] pfeng 46000000.pfe: VLAN ID incorrect or not set. Using > default V > LAN ID = 0x01. > 32m OK ] Reached target System Time Set. > [ 5.410452] pfeng 46000000.pfe: VLAN stats size incorrect or not set. > Using d > efault VLAN stats > size = 20. > [ 5.410544] pfeng 46000000.pfe: Fall-back bridge domain @ 0x20000a34 > (class) > [ 5.410551] pfeng 46000000.pfe: Default bridge domain @ 0x20000a2c (class) > [ 5.416680] pfeng 46000000.pfe: Routing table created, Hash Table @ > p0x340800 > 00, Pool @ > p0x34088000 (65536 bytes) > [ 5.416989] pfeng 46000000.pfe: Feature err051211_workaround: DISABLED > 32m OK ] Reached target System Time Synchronized. > [ 5.418364] pfeng 46000000.pfe: MDIO bus 0 disabled: Not found in DT > [ 5.418370] pfeng 46000000.pfe: MDIO bus 1 disabled: No EMAC > [ 5.418374] pfeng 46000000.pfe: MDIO bus 2 disabled: No EMAC > 32m OK ] Started Daily rotation of log files. > [ 5.418705] pfeng 46000000.pfe: HIF0 enabled > [ 5.418967] pfeng 46000000.pfe: HIF1 enabled > [ 5.419229] pfeng 46000000.pfe: HIF2 enabled > [ 5.419235] pfeng 46000000.pfe: HIF3 not configured, skipped > 32m OK ] Reached target Timers. > [ 5.424471] pfeng 46000000.pfe pfe0: registered > [ 5.424496] pfeng 46000000.pfe pfe0: Subscribe to HIF0 > 32m OK ] Listening on D-Bus System Message Bus[ 5.425044] pfeng > 46000000.pf > e pfe0: Enable > HIF0 > Socket. > [ 5.425207] pfeng 46000000.pfe pfe0: setting MAC addr: 00:01:be:be:ef:11 > [ 5.425234] pfeng 46000000.pfe pfe0: PTP HW addend 0x80000000, > max_adj c > onfigured to > 46566128 ppb > Starting sshd.socket. > [ 5.425243] pfeng 46000000.pfe: IEEE1588: Input Clock: 200000000Hz, > Output: 1 > 00000000Hz, > Accuracy: 10.0ns > [ 5.431115] pfeng 46000000.pfe pfe0: Registered PTP HW clock successfully > on > EMAC0 > [ OK ] Listening on sshd.socket. > [ OK ] Reached target Sockets. > [ OK ] Reached target Basic System. > [ OK ] Started Job spooling tools. > [ OK ] Started Periodic Command Scheduler. > [ OK ] Started D-Bus System Message Bus. > [ OK ] Started A minimalistic net…Pv4, rdisc and DHCPv6 support. > Starting IPv6 Packet Filtering Framework... > Starting IPv4 Packet Filtering Framework... > [ OK ] Started irqbalance daemon. > [ OK ] Started Hardware RNG Entropy Gatherer Daemon. > [ OK ] Started strongSwan IPsec I…IKEv2 daemon using ipsec.conf. > [ 6.625086] random: crng init done > [ 6.625101] random: 7 urandom warning(s) missed due to ratelimiting > [ OK ] Started System Logging Service. > Starting User Login Management... > Starting The Xen xenstore... > Starting OpenSSH Key Generation... > [ OK ] Finished Load/Save Random Seed. > [ OK ] Finished IPv6 Packet Filtering Framework. > [ OK ] Finished IPv4 Packet Filtering Framework. > [ OK ] Reached target Network (Pre). > Starting Network Service... > [FAILED] Failed to start The Xen xenstore. Yep, this is the problem > See 'systemctl status xenstored.service' for details. > [DEPEND] Dependency failed for xen-…des, JSON configuration stub). > [DEPEND] Dependency failed for Xenc…guest consoles and hypervisor. > [DEPEND] Dependency failed for Xend…p guests on boot and shutdown. > [DEPEND] Dependency failed for qemu for xen dom0 disk backend. > [ OK ] Started Network Service. > [ OK ] Finished OpenSSH Key Generation. > [ OK ] Started User Login Management. > Starting Network Name Resolution... > Starting Xen-watchdog - run xen watchdog daemon... > [ OK ] Started Xen-watchdog - run xen watchdog daemon. > [ OK ] Started Network Name Resolution. > [ OK ] Reached target Network. > [ OK ] Reached target Host and Network Name Lookups. > [ OK ] Started NFS status monitor for NFSv2/3 locking.. > [ OK ] Started Respond to IPv6 Node Information Queries. > [ OK ] Started Network Router Discovery Daemon. > Starting Permit User Sessions... > [ OK ] Started Xinetd A Powerful Replacement For Inetd. > [ OK ] Finished Permit User Sessions. > [ OK ] Started Getty on tty1. > [ OK ] Started Serial Getty on hvc0. > [ OK ] Started Serial Getty on ttyLF0. > [ OK ] Reached target Login Prompts. > [ OK ] Reached target Multi-User System. > Starting Update UTMP about System Runlevel Changes... > [ OK ] Finished Update UTMP about System Runlevel Changes. > > 33.Auto Linux vb3 3t.LFs32g399aevb3 hvc0 > > > >Some extra information about xenstore: > > root@s32g399aevb3:~# systemctl status xenstored.service > * xenstored.service - The Xen xenstore > Loaded: loaded (/lib/systemd/system/xenstored.service; enabled; vendor > pre> > Active: failed (Result: protocol) since Wed 2020-12-16 17:25:20 UTC; > 6min > > Process: 182 ExecStartPre=/bin/grep -q control_d /proc/xen/capabilities > (co> > Process: 186 ExecStart=/etc/xen/scripts/launch-xenstore (code=exited, > statu> > Main PID: 186 (code=exited, status=0/SUCCESS) > > Dec 16 17:25:20 s32g399aevb3 systemd[1]: Starting The Xen xenstore... > Dec 16 17:25:20 s32g399aevb3 launch-xenstore[186]: Starting > /usr/sbin/xenstored> > Dec 16 17:25:20 s32g399aevb3 launch-xenstore[193]: FATAL: Failed to open > connec> This has been truncated, but I bet there is a missing module in your Linux kernel build. Make sure you have all the following: CONFIG_XEN_BALLOON=y CONFIG_XEN_BALLOON_MEMORY_HOTPLUG=y CONFIG_XEN_SCRUB_PAGES_DEFAULT=y CONFIG_XEN_DEV_EVTCHN=y CONFIG_XEN_BACKEND=y CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=y CONFIG_XEN_GRANT_DEV_ALLOC=y CONFIG_XEN_GRANT_DMA_ALLOC=y CONFIG_SWIOTLB_XEN=y CONFIG_XEN_PRIVCMD=y > Dec 16 17:25:20 s32g399aevb3 systemd[1]: xenstored.service: Failed with > result > > Dec 16 17:25:20 s32g399aevb3 systemd[1]: Failed to start The Xen xenstore. > > > >Any idea of how can I fix that? Thank you so much for the support > > Best regards > Youssef El Mesdadi > > > > -----Ursprüngliche Nachricht----- > Von: Julien Grall <julien@xxxxxxx> > Gesendet: Dienstag, 17. Januar 2023 15:38 > An: El Mesdadi Youssef ESK UILD7 <youssef.elmesdadi@xxxxxx>; > xen-devel@xxxxxxxxxxxxxxxxxxxx > Cc: Stefano Stabellini <sstabellini@xxxxxxxxxx> > Betreff: Re: AW: Xenalyze on ARM ( NXP S32G3 with Cortex-A53) > > > > On 13/01/2023 12:56, El Mesdadi Youssef ESK UILD7 wrote: > > Hello Julien, > > Hi, > > >>>> xentrace should work on upstream Xen. What did you version did you try? > > > > While building my image using the BSP-linux of NXP, the version that was > > downloaded is Xen 4.14. > > Do you know where the source are downloaded from? > > > > > > >>>> Can you also clarify the error you are seen? > > > > The error I receive while tipping xentrace is: Command not found. > > > "Command not found" means the program hasn't been installed. > > > I assume in this Xen version, Xentrace is not compatible with ARM > > architecture > The support for xentrace on Arm has been added around Xen 4.12. So it should > work for Xen 4.14 (even though I don't recommend using older release). > > I would suggest to check how you are building the tools and which package > will be installed. > > > > > My question is, is there any new version of Xen that supports Xentrace on > > ARM? If yes how could I install it? Because Xen.4.14 was installed > > automatically by typing this ( DISTRO_FEATURES_append += "xen") in the > > local.conf file while creating my image. > > I am not familiar with the BSP-linux of NXP as this is not a project > maintained by Xen Project. > > If you need support for it, then I would suggest to discuss with NXP directly. > > > > > Or is there any source on Xentrace that is compatible with ARM on GitHub, > > that I could download and compile myself? > Even if the hypervisor is Xen, you seem to use code provided by an external > entity. I can't advise on the next steps without knowing the modification > that NXP made in the hypervisor. > > > > >>>> Yes if you assign (or provide para-virtualized driver) the > >>>> GPIO/LED/Can-Interface to the guest. > > > > Is there any tutorial that could help me create those drivers? And how > > complicated is that, to create them? > > I am not aware of any tutorial. Regarding the complexity, it all depends on > what exactly you want to do. > > > Or can they be assigned just with PCI-Passthrough? > > PCI passthrough is not yet supported on Arm. That said, I was not expecting > the GPIO/LED/Can-interface to be PCI devices. > > If they are platform devices (i.e non-PCI devices), then you could > potentially directly assign them to *one* guest (this would not work if you > need to share them). > > I wrote potentially because if the device is DMA-capabable, then the device > must be behind an IOMMU. > > Cheers, > > -- > Julien Grall > >
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |