|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] AW: AW: Xenstore failed to start / Xenalyze on ARM ( NXP S32G3 with Cortex-A53)
> hello Julien,
>first of all thank you so much for the support, after flashing Xen on the
>S32G3 I noticed that I cannot create DomUs.
>when I also give the xl list, it does not even show Dom0 and stays blocked.
root@s32g399aevb3:~# xl list
Name ID Mem VCPUs State Time(s)
root@s32g399aevb3:~#
>I assume this is because xenstore failed to start, the error is shown in the
>messages during the boot time.
[FAILED] Failed to start The Xen xenstore.
See 'systemctl status xenstored.service' for details.
[FAILED] Failed to mount NFSD configuration filesystem.
See 'systemctl status proc-fs-nfsd.mount' for details.
>Here is xl.conf in case you need information about this file:
root@s32g399aevb3:/etc/xen# cat xl.conf
## Global XL config file ##
# Set domain-id policy. "xen" means that the hypervisor will choose the
# id of a new domain. "random" means that a random value will be chosen.
#domid_policy="xen"
# Control whether dom0 is ballooned down when xen doesn't have enough
# free memory to create a domain. "auto" means only balloon if dom0
# starts with all the host's memory.
#autoballoon="auto"
# full path of the lockfile used by xl during domain creation
#lockfile="/var/lock/xl"
# default output format used by "xl list -l"
#output_format="json"
# first block device to be used for temporary VM disk mounts
#blkdev_start="xvda"
# default option to run hotplug scripts from xl
# if disabled the old behaviour will be used, and hotplug scripts will be
# launched by udev.
#run_hotplug_scripts=1
# default backend domain to connect guest vifs to. This can be any
# valid domain identifier.
#vif.default.backend="0"
# default gateway device to use with vif-route hotplug script
#vif.default.gatewaydev="eth0"
# default vif script to use if none is specified in the guest config
#vif.default.script="vif-bridge"
# default bridge device to use with vif-bridge hotplug scripts
#vif.default.bridge="xenbr0"
# Reserve a claim of memory when launching a guest. This guarantees immediate
# feedback whether the guest can be launched due to memory exhaustion
# (which can take a long time to find out if launching huge guests).
# see xl.conf(5) for details.
#claim_mode=1
# Specify global vcpu hard affinity masks. See xl.conf(5) for details.
#vm.cpumask="0-7"
#vm.pv.cpumask="0-3"
#vm.hvm.cpumask="3-7"
>next are the messages during the boot time:
NOTICE: Reset status: Power-On Reset
NOTICE: BL2: v2.5(release):bsp33.0-2.5-dirty
NOTICE: BL2: Built : 14:01:09, Jun 15 2022
NOTICE: BL2: Booting BL31
U-Boot 2020.04+g9cdfca686e (Jun 10 2022 - 11:46:41 +0000)
CPU: NXP S32G399A rev. 1.0
Model: NXP S32G3XXX-EVB
DRAM: 3.5 GiB
MMC: FSL_SDHC: 0
Loading Environment from MMC... OK
Using internal clock for PCIe0, CRNS
Configuring PCIe0 as RootComplex(x2)
Using internal clock for PCIe1, CRNS
Frequency 100Mhz configured for PCIe1
Configuring PCIe1 as SGMII [XPCS0 1G, XPCS1 OFF(PCIex1)]
Setting PCI Device and Vendor IDs to 0x4300:0x1957
PCIe0: Failed to get link up
Pcie0: LINK_DBG_1: 0x00000000, LINK_DBG_2: 0x00000800 (expected 0x000000d1)
DEBUG_R0: 0x00ed4001, DEBUG_R1: 0x08600000
PCI: Failed autoconfig bar 1c
PCIe1: Not configuring PCIe, PHY not configured
In: serial@401c8000
Out: serial@401c8000
Err: serial@401c8000
Loading SJA1105 firmware over SPI 5:0
No matching device ID found for devid FFFFFFFF, cs 0.
Error SJA1105 configuration not completed
Net: EQOS phy: rgmii @ 4
Warning: eth_eqos (eth0) using random MAC address - f6:65:86:a2:0e:f8
eth0: eth_eqos PFE: emac0: sgmii emac1: none emac2: none
Warning: eth_pfeng using MAC address from ROM
, eth1: eth_pfeng
Hit any key to stop autoboot: 0
PFE: emac0: sgmii emac1: none emac2: none
PFE: emac0: sgmii emac1: none emac2: none
1039 bytes read in 9 ms (112.3 KiB/s)
## Executing script at 80200000
1048688 bytes read in 36 ms (27.8 MiB/s)
14034952 bytes read in 201 ms (66.6 MiB/s)
38461 bytes read in 9 ms (4.1 MiB/s)
## Flattened Device Tree blob at 86600000
Booting using the fdt blob at 0x86600000
Using Device Tree in place at 0000000086600000, end 000000008660dfff
DT: Enabling PFE
DT: Enabling PFE_EMAC_0
DT: pfe0 set to 00:01:be:be:ef:11
DT: Disabling PFE_EMAC_1
DT: Disabling PFE_EMAC_2
Starting kernel ...
- UART enabled -
- Boot CPU booting -
- Current EL 00000008 -
- Initialize CPU -
- Turning on paging -
- Zero BSS -
- Ready -
(XEN) Checking for initrd in /chosen
(XEN) RAM: 0000000080000000 - 00000000ffffffff
(XEN) RAM: 0000000880000000 - 00000008dfffffff
(XEN)
(XEN) MODULE[0]: 0000000085600000 - 00000000857430c8 Xen
(XEN) MODULE[1]: 0000000086600000 - 000000008660a000 Device Tree
(XEN) MODULE[2]: 0000000085800000 - 0000000086562808 Kernel
(XEN) RESVD[0]: 00000000ff800000 - 00000000ff9fffff
(XEN) RESVD[1]: 00000000c0000000 - 00000000c03fffff
(XEN) RESVD[2]: 00000000c0400000 - 00000000c07fffff
(XEN) RESVD[3]: 00000000d0000000 - 00000000d03fffff
(XEN) RESVD[4]: 0000000084000000 - 000000008407ffff
(XEN) RESVD[5]: 0000000034000000 - 000000003407ffff
(XEN) RESVD[6]: 0000000034080000 - 000000003409ffff
(XEN) RESVD[7]: 0000000083200000 - 00000000835dffff
(XEN) RESVD[8]: 00000000835e0000 - 00000000835fffff
(XEN)
(XEN)
(XEN) Command line: dom0_mem=512M dom0_max_vcpus=1 bootscrub=0
(XEN) PFN compression on bits 20...22
(XEN) Domain heap initialised
(XEN) Booting using Device Tree
(XEN) Platform: NXP S32-Gen1
(XEN) No dtuart path configured
(XEN) Bad console= option 'dtuart'
Xen 4.14.0
(XEN) Xen version 4.14.0 (xen-4.14-r0@fsl-auto) (aarch64-fsl-linux-gcc (GCC)
10.
2.0) debug=y 2022-05-18
(XEN) Latest ChangeSet: Wed May 18 15:47:26 2022 +0300 git:becdd18e50-dirty
(XEN) build-id: c93be820bfe87b5abccd95ea86e98121e1231249
(XEN) Processor: 410fd034: "ARM Limited", variant: 0x0, part 0xd03, rev 0x4
(XEN) 64-bit Execution:
(XEN) Processor Features: 0000000001002222 0000000000000000
(XEN) Exception Levels: EL3:64+32 EL2:64+32 EL1:64+32 EL0:64+32
(XEN) Extensions: FloatingPoint AdvancedSIMD GICv3-SysReg
(XEN) Debug Features: 0000000010305106 0000000000000000
(XEN) Auxiliary Features: 0000000000000000 0000000000000000
(XEN) Memory Model Features: 0000000000001122 0000000000000000
(XEN) ISA Features: 0000000000011120 0000000000000000
(XEN) 32-bit Execution:
(XEN) Processor Features: 00000131:10011011
(XEN) Instruction Sets: AArch32 A32 Thumb Thumb-2 Jazelle
(XEN) Extensions: GenericTimer Security
(XEN) Debug Features: 03010066
(XEN) Auxiliary Features: 00000000
(XEN) Memory Model Features: 10201105 40000000 01260000 02102211
(XEN) ISA Features: 02101110 13112111 21232042 01112131 00011142 00011121
(XEN) Using SMC Calling Convention v1.2
(XEN) Using PSCI v1.1
(XEN) SMP: Allowing 8 CPUs
(XEN) enabled workaround for: ARM erratum 1530924
(XEN) Generic Timer IRQ: phys=30 hyp=26 virt=27 Freq: 5000 KHz
(XEN) GICv3 initialization:
(XEN) gic_dist_addr=0x00000050800000
(XEN) gic_maintenance_irq=25
(XEN) gic_rdist_stride=0
(XEN) gic_rdist_regions=1
(XEN) redistributor regions:
(XEN) - region 0: 0x00000050900000 - 0x00000050b00000
(XEN) GICv3 compatible with GICv2 cbase 0x00000050400000 vbase 0x00000050420000
(XEN) GICv3: 576 lines, (IID 0001143b).
(XEN) GICv3: CPU0: Found redistributor in region 0 @000000004001a000
(XEN) XSM Framework v1.0.0 initialized
(XEN) Initialising XSM SILO mode
(XEN) Using scheduler: SMP Credit Scheduler rev2 (credit2)
(XEN) Initializing Credit2 scheduler
(XEN) load_precision_shift: 18
(XEN) load_window_shift: 30
(XEN) underload_balance_tolerance: 0
(XEN) overload_balance_tolerance: -3
(XEN) runqueues arrangement: socket
(XEN) cap enforcement granularity: 10ms
(XEN) load tracking window length 1073741824 ns
(XEN) Allocated console ring of 64 KiB.
(XEN) CPU0: Guest atomics will try 13 times before pausing the domain
(XEN) Bringing up CPU1
- CPU 00000001 booting -
- Current EL 00000008 -
- Initialize CPU -
- Turning on paging -
- Ready -
(XEN) GICv3: CPU1: Found redistributor in region 0 @000000004003a000
(XEN) CPU1: Guest atomics will try 15 times before pausing the domain
(XEN) CPU 1 booted.
(XEN) Bringing up CPU2
- CPU 00000100 booting -
- Current EL 00000008 -
- Initialize CPU -
- Turning on paging -
- Ready -
(XEN) GICv3: CPU2: Found redistributor in region 0 @000000004009a000
(XEN) CPU2: Guest atomics will try 15 times before pausing the domain
(XEN) CPU 2 booted.
(XEN) Bringing up CPU3
- CPU 00000101 booting -
- Current EL 00000008 -
- Initialize CPU -
- Turning on paging -
- Ready -
(XEN) GICv3: CPU3: Found redistributor in region 0 @00000000400ba000
(XEN) CPU3: Guest atomics will try 15 times before pausing the domain
(XEN) CPU 3 booted.
(XEN) Bringing up CPU4
- CPU 00000002 booting -
- Current EL 00000008 -
- Initialize CPU -
- Turning on paging -
- Ready -
(XEN) GICv3: CPU4: Found redistributor in region 0 @000000004005a000
(XEN) CPU4: Guest atomics will try 14 times before pausing the domain
(XEN) CPU 4 booted.
(XEN) Bringing up CPU5
- CPU 00000003 booting -
- Current EL 00000008 -
- Initialize CPU -
- Turning on paging -
- Ready -
(XEN) GICv3: CPU5: Found redistributor in region 0 @000000004007a000
(XEN) CPU5: Guest atomics will try 15 times before pausing the domain
(XEN) CPU 5 booted.
(XEN) Bringing up CPU6
- CPU 00000102 booting -
- Current EL 00000008 -
- Initialize CPU -
- Turning on paging -
- Ready -
(XEN) GICv3: CPU6: Found redistributor in region 0 @00000000400da000
(XEN) CPU6: Guest atomics will try 16 times before pausing the domain
(XEN) CPU 6 booted.
(XEN) Bringing up CPU7
- CPU 00000103 booting -
- Current EL 00000008 -
- Initialize CPU -
- Turning on paging -
- Ready -
(XEN) GICv3: CPU7: Found redistributor in region 0 @00000000400fa000
(XEN) CPU7: Guest atomics will try 15 times before pausing the domain
(XEN) CPU 7 booted.
(XEN) Brought up 8 CPUs
(XEN) I/O virtualisation disabled
(XEN) P2M: 40-bit IPA with 40-bit PA and 8-bit VMID
(XEN) P2M: 3 levels with order-1 root, VTCR 0x80023558
(XEN) Scheduling granularity: cpu, 1 CPU per sched-resource
(XEN) Adding cpu 0 to runqueue 0
(XEN) First cpu on runqueue, activating
(XEN) Adding cpu 1 to runqueue 0
(XEN) Adding cpu 2 to runqueue 0
(XEN) Adding cpu 3 to runqueue 0
(XEN) Adding cpu 4 to runqueue 0
(XEN) Adding cpu 5 to runqueue 0
(XEN) Adding cpu 6 to runqueue 0
(XEN) Adding cpu 7 to runqueue 0
(XEN) alternatives: Patching with alt table 00000000002d4308 -> 00000000002d4b3c
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Loading d0 kernel from boot module @ 0000000085800000
(XEN) Allocating 1:1 mappings totalling 512MB for dom0:
(XEN) BANK[0] 0x000000a0000000-0x000000c0000000 (512MB)
(XEN) Grant table range: 0x00000085600000-0x00000085640000
(XEN) Allocating PPI 16 for event channel interrupt
(XEN) Loading zImage from 0000000085800000 to 00000000a0000000-00000000a0d62808
(XEN) Loading d0 DTB to 0x00000000a8000000-0x00000000a800947a
(XEN) Initial low memory virq threshold set at 0x4000 pages.
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) *** Serial input to DOM0 (type 'CTRL-a' three times to switch input)
(XEN) Freed 352kB init memory.
(XEN) d0v0: vGICD: RAZ on reserved register offset 0x00000c
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER4
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER8
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER12
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER16
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER20
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER24
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER28
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER32
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER36
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER40
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER44
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER48
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER52
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER56
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER60
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER64
(XEN) d0v0: vGICD: unhandled word write 0x000000ffffffff to ICACTIVER68
(XEN) d0v0: vGICR: SGI: unhandled word write 0x000000ffffffff to ICACTIVER0
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.10.109-rt65+g0bace7fde5f5 (oe-user@oe-host)
(aarc
h64-fsl-linux-gcc (GCC)
10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP PREEMPT Fri
Jun 24 15:01:08 UTC 2022
[ 0.000000] Machine model: NXP S32G3XXX-EVB3
[ 0.000000] Xen 4.14 support found
[ 0.000000] Reserved memory: created DMA memory pool at 0x0000000083200000,
s
ize 3 MiB
[ 0.000000] OF: reserved mem: initialized node pfebufs@83200000, compatible
i
d shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000034000000-0x00000000ff9fffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000034000000-0x000000003409ffff]
[ 0.000000] node 0: [mem 0x0000000083200000-0x00000000835dffff]
[ 0.000000] node 0: [mem 0x00000000835e0000-0x00000000835fffff]
[ 0.000000] node 0: [mem 0x0000000084000000-0x000000008407ffff]
[ 0.000000] node 0: [mem 0x00000000a0000000-0x00000000bfffffff]
[ 0.000000] node 0: [mem 0x00000000c0000000-0x00000000c07fffff]
[ 0.000000] node 0: [mem 0x00000000d0000000-0x00000000d03fffff]
[ 0.000000] node 0: [mem 0x00000000ff800000-0x00000000ff9fffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000034000000-0x00000000ff9fffff]
[ 0.000000] cma: Reserved 256 MiB at 0x00000000ad000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 17 pages/cpu s32024 r8192 d29416 u69632
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, 1530923, or
1530924
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 134109
[ 0.000000] Kernel command line: console=ttyLF0,115200 earlycon=xen
earlyprin
tk=xen
root=/dev/mmcblk0p2 rw clk_ignore_unused
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576
bytes,
linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes,
li
near)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 202252K/543872K available (8766K kernel code, 650K
rwdata
, 2880K rodata, 1344K
init, 245K bss, 79476K reserved, 262144K cma-reserved)
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25
jif
fies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: 544 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000050900000
[ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x4ec
wit
h crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 5.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
max_cycles:
0x127350b88,
max_idle_ns: 440795202120 ns
[ 0.000001] sched_clock: 56 bits at 5MHz, resolution 200ns, wraps every
43980
46511100ns
[ 0.000357] Console: colour dummy device 80x25
[ 0.000385] Calibrating delay loop (skipped), value calculated using timer
fr
equency.. 10.00 BogoMIPS
(lpj=20000)
[ 0.000395] pid_max: default: 32768 minimum: 301
[ 0.000489] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes,
line
ar)
[ 0.000500] Mountpoint-cache hash table entries: 2048 (order: 2, 16384
bytes,
linear)
[ 0.001943] xen:grant_table: Grant tables using version 1 layout
[ 0.001964] Grant table initialized
[ 0.001994] xen:events: Using FIFO-based ABI
[ 0.002023] Xen: initializing cpu0
[ 0.002127] rcu: Hierarchical SRCU implementation.
[ 0.002412] smp: Bringing up secondary CPUs ...
[ 0.002415] smp: Brought up 1 node, 1 CPU
[ 0.002419] SMP: Total of 1 processors activated.
[ 0.002427] CPU features: detected: 32-bit EL0 Support
[ 0.002433] CPU features: detected: CRC32 instructions
[ 0.009718] CPU: All CPU(s) started at EL1
[ 0.009731] alternatives: patching kernel code
[ 0.010183] devtmpfs: initialized
[ 0.014415] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
ma
x_idle_ns: 7645041785100000 ns
[ 0.014429] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[ 0.020426] pinctrl core: initialized pinctrl subsystem
[ 0.020983] NET: Registered protocol family 16
[ 0.022141] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.022218] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic
allo
cations
[ 0.022309] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic
al
locations
[ 0.022851] thermal_sys: Registered thermal governor 'step_wise'
[ 0.023110] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.023153] ASID allocator initialised with 65536 entries
[ 0.023218] xen:swiotlb_xen: Warning: only able to allocate 4 MB for
software
IO TLB
[ 0.023933] software IO TLB: mapped [mem
0x00000000a1800000-0x00000000a1c0000
0] (4MB)
[ 0.023998] Serial: AMBA PL011 UART driver
[ 0.024571] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 0.024649] arm-scmi firmware:scmi: No. of Protocol > MAX_PROTOCOLS_IMP
[ 0.024654] arm-scmi firmware:scmi: SCMI Protocol v2.0 'NXP:S32G399A'
Firmwar
e version 0x0
[ 0.039850] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.039858] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.039862] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.039866] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.043412] scmi-clocks scmi_dev.1: failed to register clock 87
[ 0.043421] scmi-clocks scmi_dev.1: failed to register clock 88
[ 0.043428] scmi-clocks scmi_dev.1: failed to register clock 89
[ 0.043434] scmi-clocks scmi_dev.1: failed to register clock 90
[ 0.043507] scmi-clocks scmi_dev.1: failed to register clock 95
[ 0.043514] scmi-clocks scmi_dev.1: failed to register clock 96
[ 0.043520] scmi-clocks scmi_dev.1: failed to register clock 97
[ 0.043526] scmi-clocks scmi_dev.1: failed to register clock 98
[ 0.046871] xen:balloon: Initialising balloon driver
[ 0.047230] vgaarb: loaded
[ 0.047367] SCSI subsystem initialized
[ 0.047494] usbcore: registered new interface driver usbfs
[ 0.047521] usbcore: registered new interface driver hub
[ 0.047541] usbcore: registered new device driver usb
[ 0.047818] pps_core: LinuxPPS API ver. 1 registered
[ 0.047821] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giome
tti <giometti@xxxxxxxx>
[ 0.047831] PTP clock support registered
[ 0.048664] clocksource: Switched to clocksource arch_sys_counter
[ 0.053083] NET: Registered protocol family 2
[ 0.053173] IP idents hash table entries: 16384 (order: 5, 131072 bytes,
line
ar)
[ 0.053762] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192
bytes, linear)
[ 0.053787] TCP established hash table entries: 8192 (order: 4, 65536 bytes,
linear)
[ 0.053847] TCP bind hash table entries: 8192 (order: 5, 131072 bytes,
linear
)
[ 0.053970] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.054028] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.054052] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.054147] NET: Registered protocol family 1
[ 0.054435] RPC: Registered named UNIX socket transport module.
[ 0.054439] RPC: Registered udp transport module.
[ 0.054441] RPC: Registered tcp transport module.
[ 0.054443] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.054451] PCI: CLS 0 bytes, default 64
[ 0.055375] workingset: timestamp_bits=62 max_order=17 bucket_order=0
[ 0.055858] fuse: init (API version 7.32)
[ 0.055965] NET: Registered protocol family 38
[ 0.055988] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
2
48)
[ 0.055993] io scheduler mq-deadline registered
[ 0.055997] io scheduler kyber registered
[ 0.057025] s32g-siul2-pinctrl 4009c240.siul2-pinctrl: initialized s32
pinctr
l driver
[ 0.057965] gpio-339 (llcecan0-en): hogged as output/high
[ 0.057983] gpio-340 (llcecan0-stby): hogged as output/high
[ 0.057998] gpio-342 (llcecan4-en): hogged as output/high
[ 0.058014] gpio-343 (llcecan4-stby): hogged as output/high
[ 0.058029] gpio-345 (llcecan5-en): hogged as output/high
[ 0.058044] gpio-346 (llcecan5-stby): hogged as output/high
[ 0.058058] gpio-351 (llcecan6-en): hogged as output/high
[ 0.058072] gpio-352 (llcecan6-stby): hogged as output/high
[ 0.058089] gpio-353 (llcecan12-stby): hogged as output/high
[ 0.058103] gpio-358 (llcecan12-en): hogged as output/high
[ 0.058120] gpio-360 (llcecan13-en): hogged as output/high
[ 0.058135] gpio-361 (llcecan13-stby): hogged as output/high
[ 0.058151] gpio-382 (llcecan15-en): hogged as output/high
[ 0.058165] gpio-383 (llcecan15-stby): hogged as output/high
[ 0.059358] xen:xen_evtchn: Event-channel device installed
[ 0.060467] serial: Freescale linflex driver
[ 0.060686] 401c8000.serial: ttyLF0 at MMIO 0x401c8000 (irq = 25, base_baud
=
7812500) is a FSL_LINFLEX
[ 0.060735] printk: console [ttyLF0] enabled
[ 0.061072] 401cc000.serial: ttyLF1 at MMIO 0x401cc000 (irq = 26, base_baud
=
7812500) is a FSL_LINFLEX
[ 0.061385] 402bc000.serial: ttyLF2 at MMIO 0x402bc000 (irq = 44, base_baud
=
7812500) is a FSL_LINFLEX
[ 0.061832] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.061846] Invalid max_queues (4), will use default max: 1.
[ 0.062193] fsl_fccu 4030c000.fccu: FCCU status is 0 (normal)
[ 0.063813] spi-nor spi0.0: mt35xu02g (262144 Kbytes)
[ 0.065365] vcan: Virtual CAN interface driver
[ 0.065370] slcan: serial line CAN interface driver
[ 0.065372] slcan: 10 dynamic interface channels.
[ 0.065377] CAN device driver interface
[ 0.065555] e100: Intel(R) PRO/100 Network Driver
[ 0.065558] e100: Copyright(c) 1999-2006 Intel Corporation
[ 0.065585] e1000: Intel(R) PRO/1000 Network Driver
[ 0.065588] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 0.065615] e1000e: Intel(R) PRO/1000 Network Driver
[ 0.065616] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 0.065642] igb: Intel(R) Gigabit Ethernet Network Driver
[ 0.065645] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 0.065920] xen_netfront: Initialising Xen virtual ethernet driver
[ 0.066016] hse-uio 40211000.mu1b: firmware not found
[ 0.066208] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.066213] ehci-pci: EHCI PCI platform driver
[ 0.066318] usbcore: registered new interface driver uas
[ 0.066346] usbcore: registered new interface driver usb-storage
[ 0.067503] s32gen1-rtc 40060000.rtc: registered as rtc0
[ 0.067533] s32gen1-rtc 40060000.rtc: setting system clock to
1970-01-01T00:0
0:00 UTC (0)
[ 0.067665] i2c /dev entries driver
[ 0.068026] sac58r-wdt 4010c000.swt: SAC58R/S32GEN1 Watchdog Timer
Registered
. timeout=30s
(nowayout=0)
[ 0.068204] sac58r-wdt 40200000.swt: SAC58R/S32GEN1 Watchdog Timer
Registered
. timeout=30s
(nowayout=0)
[ 0.068371] sac58r-wdt 40204000.swt: SAC58R/S32GEN1 Watchdog Timer
Registered
. timeout=30s
(nowayout=0)
[ 0.068538] sac58r-wdt 40208000.swt: SAC58R/S32GEN1 Watchdog Timer
Registered
. timeout=30s
(nowayout=0)
[ 0.068776] sac58r-wdt 40500000.swt: SAC58R/S32GEN1 Watchdog Timer
Registered
. timeout=30s
(nowayout=0)
[ 0.068950] sac58r-wdt 40504000.swt: SAC58R/S32GEN1 Watchdog Timer
Registered
. timeout=30s
(nowayout=0)
[ 0.069112] sac58r-wdt 40508000.swt: SAC58R/S32GEN1 Watchdog Timer
Registered
. timeout=30s
(nowayout=0)
[ 0.069279] sac58r-wdt 4050c000.swt: SAC58R/S32GEN1 Watchdog Timer
Registered
. timeout=30s
(nowayout=0)
[ 0.069492] sdhci: Secure Digital Host Controller Interface driver
[ 0.069495] sdhci: Copyright(c) Pierre Ossman
[ 0.069497] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.069837] mmc0: CQHCI version 5.10
[ 0.070452] hse 40210000.mu0b: firmware not found
[ 0.070658] usbcore: registered new interface driver usbhid
[ 0.070662] usbhid: USB HID core driver
[ 0.082993] s32-adc 401f8000.adc: Device initialized successfully.
[ 0.094947] s32-adc 402e8000.adc: Device initialized successfully.
[ 0.095109] nxp_s32_ddr_perf 403e0000.ddr-perf: probing device
[ 0.095353] nxp_s32_ddr_perf 403e0000.ddr-perf: device initialized
successful
ly
[ 0.095430] s32-siul2-nvmem 4009c000.nvram: initialize s32 siul2 nvmem driver
[ 0.095550] s32-siul2-nvmem 44010000.nvram: initialize s32 siul2 nvmem driver
[ 0.095949] NET: Registered protocol family 10
[ 0.096436] Segment Routing with IPv6
[ 0.096476] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 0.096852] NET: Registered protocol family 17
[ 0.096947] can: controller area network core
[ 0.096980] NET: Registered protocol family 29
[ 0.096984] can: raw protocol
[ 0.096989] can: broadcast manager protocol
[ 0.096996] can: netlink gateway - max_hops=1
[ 0.097014] 8021q: 802.1Q VLAN Support v1.8
[ 0.097149] printk: console [ttyLF0]: printing thread started
[ 0.100703] mmc0: SDHCI controller on 402f0000.usdhc [402f0000.usdhc] using
A
DMA
[ 0.108674] phy-s32gen1-serdes 40480000.serdes: Using mode 0 for SerDes
subsy
stem
[ 0.109020] phy-s32gen1-serdes 44180000.serdes: Using mode 3 for SerDes
subsy
stem
[ 0.115131] phy-s32gen1-serdes 44180000.serdes: Unstable RX detected on XPCS1
[ 0.115158] phy-s32gen1-serdes 44180000.serdes: Unstable RX detected on XPCS0
[ 0.115337] s32gen1-pcie 40400000.pcie: Configured as RootComplex
[ 0.115627] s32gen1-pcie 40400000.pcie: Setting PCI Device and Vendor IDs to
0x4300:0x1957
[ 0.116614] s32gen1-pcie 40400000.pcie: Allocated line 0 for interrupt 52
(ms
i)
[ 0.383316] mmc0: Command Queue Engine enabled
[ 0.383326] mmc0: new DDR MMC card at address 0001
[ 0.391409] mmcblk0: mmc0:0001 G1M15M 59.3 GiB
[ 0.391539] mmcblk0boot0: mmc0:0001 G1M15M partition 1 31.5 MiB
[ 0.391661] mmcblk0boot1: mmc0:0001 G1M15M partition 2 31.5 MiB
[ 0.391804] mmcblk0rpmb: mmc0:0001 G1M15M partition 3 4.00 MiB, chardev
(243:
0)
[ 0.399208] mmcblk0: p1 p2 p3
[ 1.136116] s32gen1-pcie 40400000.pcie: Failed to stabilize PHY link
[ 1.136123] s32gen1-pcie 40400000.pcie: Configuring as RootComplex
[ 1.136136] s32gen1-pcie 40400000.pcie: host bridge /soc/pcie@40400000
ranges
:
[ 1.136177] s32gen1-pcie 40400000.pcie: IO 0x5ffffe0000..0x5ffffeffff
-
> 0x0000000000
[ 1.136195] s32gen1-pcie 40400000.pcie: MEM 0x5800000000..0x5ffffdffff
-
> 0x0000000000
(XEN) physdev.c:16:d0v0 PHYSDEVOP cmd=25: not implemented
[ 2.142041] s32gen1-pcie 40400000.pcie: Phy link never came up
(XEN) physdev.c:16:d0v0 PHYSDEVOP cmd=15: not implemented
[ 2.142133] s32gen1-pcie 40400000.pcie: PCI host bridge to bus 0000:00
[ 2.142139] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.142147] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 2.142153] pci_bus 0000:00: root bus resource [mem
0x5800000000-0x5ffffdffff
] (bus
address [0x00000000-0x7fffdffff])
[ 2.142201] pci 0000:00:00.0: [16c3:4300] type 01 class 0x060400
[ 2.142224] pci 0000:00:00.0: reg 0x10: [mem 0x5800000000-0x58000fffff]
[ 2.142242] pci 0000:00:00.0: reg 0x38: [mem 0x5800000000-0x580000ffff pref]
[ 2.142339] pci 0000:00:00.0: supports D1
[ 2.142344] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold
[ 2.165526] pci 0000:00:00.0: Failed to add - passthrough or MSI/MSI-X might
fail!
[ 2.168521] pci 0000:00:00.0: BAR 0: assigned [mem 0x5800000000-0x58000fffff]
[ 2.168532] pci 0000:00:00.0: BAR 6: assigned [mem 0x5800100000-0x580010ffff
pref]
[ 2.168541] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.168839] pcieport 0000:00:00.0: PME: Signaling with IRQ 67
[ 2.175158] clk: Not disabling unused clocks
[ 2.270457] random: fast init done
[ 2.282422] EXT4-fs (mmcblk0p2): recovery complete
[ 2.283171] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode.
O
pts: (null)
[ 2.283229] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 2.283571] devtmpfs: mounted
[ 2.284179] Freeing unused kernel memory: 1344K
[ 2.284312] Run /sbin/init as init process
[ 2.413488] systemd[1]: System time before build time, advancing clock.
[ 2.441298] systemd[1]: systemd 246 running in system mode. (+PAM -AUDIT
-SEL
INUX +IMA -APPARMOR -SMACK
+SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +
XZ -LZ4 -ZSTD -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN
-PCRE2 default-hierarch
y=hybrid)
W[ 2.442307] systemd[1]: Detected architecture arm64.
elcome to Auto Linux BSP 33.0 (gatesgarth)!
[ 2.484975] systemd[1]: Set hostname to <s32g399aevb3>.
[ 2.577683] systemd-sysv-generator[76]: SysV service '/etc/init.d/netperf'
la
cks a native systemd unit
file. Automatically generating a unit file for compati
bility. Please update package to include a native systemd
unit file, in order to
make it
more safe and robust.
[ 2.766744] systemd[1]:
/lib/systemd/system/xen-qemu-dom0-disk-backend.servic
e:11: PIDFile= references a path below legacy directory
/var/run/, updating /var
/run/xen/qemu-dom0.pid → /run/xen/qemu-dom0.pid; please update the unit file
acc
ordingly.
[ OK [ 2.849603] systemd[1]: Queued start job for default target
Multi-User
System.
random: systemd: uninitialized urandom read (16 bytes read)
[[ 2.851615] systemd[1]: Created slice system-getty.slice.
0m] Created slice system-getty.slice.
[ OK ] Created slice sy[ 2.884743] random: systemd: uninitialized urandom
r
ead (16 bytes read)
s[ 2.885064] systemd[1]: Created slice system-modprobe.slice.
tem-modprobe.slice.
[ OK ] Created slice sys[ 2.912705] random: systemd: uninitialized urandom
read (16 bytes read)
t[ 2.913002] systemd[1]: Created slice system-serial\x2dgetty.slice.
em-serial\x2dgetty.slice.
[ OK ] Created slice Use[ 2.940962] systemd[1]: Created slice User and
Sess
ion Slice.
r and Session Slice.
[ OK ] Started Dispatch P[ 2.960876] systemd[1]: Started Dispatch Password
Requests to Console Directory
Watch.
assword …ts to Console Directory Watch.
[ OK ] Started Forward Pas[ 2.988824] systemd[1]: Started Forward Password
Requests to Wall Directory Watch.
sword R…uests to Wall Directory Watch.
[ OK ] Reached target Path[ 3.012877] systemd[1]: Reached target Paths.
s.
[ OK ] Reached target Remot[ 3.032754] systemd[1]: Reached target Remote
Fi
le Systems.
e File Systems.
[ OK ] Reached target Slice[ 3.052744] systemd[1]: Reached target Slices.
s.
[ OK ] Reached target Swap systemd[1]: Reached target Swap.
[0m.
[ OK systemd[1]: Listening on RPCbind Server Activation Socket.
[0m] Listening on RPCbind Server Activation Socket.
[ OK ] Reached target RPC [ 3.124844] systemd[1]: Reached target RPC Port
M
apper.
Port Mapper.
[ OK ] Listening on Sy[ 3.145153] systemd[1]: Listening on Syslog Socket.
slog Socket.
[ OK ] Listening on initc[ 3.164886] systemd[1]: Listening on initctl
Compa
tibility Named Pipe.
tl Compatibility Named Pipe.
[ OK 3.191035] systemd[1]: Condition check resulted in Journal Audit
Socke
t being skipped.
m[ 3.191496] systemd[1]: Listening on Journal Socket (/dev/log).
] Listening on Journal Socket (/dev/log).
[ OK ] Listening on Jou[ 3.221106] systemd[1]: Listening on Journal Socket.
rnal Socket.
[ OK ] Listening on Ne[ 3.241190] systemd[1]: Listening on Network Service
Netlink Socket.
twork Service Netlink Socket.
[ OK ] Listening on ude[ 3.265051] systemd[1]: Listening on udev Control
So
cket.
v Control Socket.
[ OK ] Listening on udev [ 3.284919] systemd[1]: Listening on udev Kernel
S
ocket.
Kernel Socket.
[ OK ] Listening on User [ 3.304936] systemd[1]: Listening on User
Database
Manager Socket.
Database Manager Socket.
Mounting H[ 3.330591] systemd[1]: Mounting Huge Pages File System...
uge Pages File System...
Mounting 3.353156] systemd[1]: Condition check resulted in POSIX
Me
ssage Queue File System being
skipped.
;39mMount /proc/xen files...
[ 3.354954] systemd[1]: Mounting Mount /proc/xen files...
[ 3.370933] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
Starti[ 3.401191] systemd[1]: Condition check resulted in Kernel
Tra
ce File System being skipped.
ng Load Kernel Module con[ 3.401679] systemd[1]: Condition check resulted in
Create list of static device
nodes for the current kernel being skipped.
fi[ 3.403642] systemd[1]: Starting Load Kernel Module configfs...
gfs...
Starting 3.446771] systemd[1]: Starting Load Kernel Module drm...
9mLoad Kernel Module drm...
Starting 3.470771] systemd[1]: Starting Load Kernel Module fuse...
9mLoad Kernel Module fuse...
Starting 3.494788] systemd[1]: Starting RPC Bind...
9mRPC Bind...
[ 3.513000] systemd[1]: Condition check resulted in File System Check
on
Root Device being skipped.
Starting Jour[ 3.516455] systemd[1]: Starting Journal Service...
nal Service...
[ 3.548101] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
Starting 3.570819] systemd[1]: Starting Remount Root and Kernel
Fil
e Systems...
9mRemount Root and Kernel File Systems...
[ 3.595018] systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
[ 3.632457] llce_core 43ff8000.llce: Successfully loaded LLCE firmware
[ 3.639641] systemd[1]: Started RPC Bind.
32m OK ] Started RPC Bind.
[ 3.651233] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 3.706544] systemd[1]: Mounted Huge Pages File System.
32m OK ] Mounted Huge Pages File System.
[ 3.729184] systemd[1]: Mounted Mount /proc/xen files.
32m OK ] Mounted Mount /proc/xen files.
[ OK ] Started Journa[ 3.749158] systemd[1]: Started Journal Service.
l Service.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module drm.
[ 3.804694] llce_mb 43a00000.llce_mb: LLCE firmware version: GGEE_3A
[ 3.804711] llce_mb 43a00000.llce_mb: LLCE firmware: logging support disabled
[ OK ] Finished Load Kernel Module fuse.
[ OK ] Finished Remount Root and Kernel File Systems.
Mounting FUSE Control File System...
Mounting Kernel Configuration File System...
[ 3.916363] llce_can: unknown parameter 'logging' ignored
Starting Flush Journal to Persistent Storage...
Starting Create Static Device Nodes in /dev...
[ OK ] Mounted FUSE Control File System.
[ OK ] Finished Load Kernel Modules.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
Mounting NFSD configuration filesystem...
Mounting /tmp...
Mounting mount xenstore file system...
Mounting /var/volatile...
Starting Apply Kernel Variables...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Finished Coldplug All udev Devices.
[FAILED] Failed to mount NFSD configuration filesystem.
See 'systemctl status proc-fs-nfsd.mount' for details.
[DEPEND] Dependency failed for NFS server and services.
[DEPEND] Dependency failed for NFS Mount Daemon.
[ OK ] Started Rule-based Manager for Device Events and Files.
[ OK ] Mounted /tmp.
[ OK ] Mounted mount xenstore file system.
[ OK ] Mounted /var/volatile.
[ OK ] Finished Apply Kernel Variables.
Mounting /var/volatile/tmp...
Starting Load/Save Random Seed...
[ OK ] Mounted /var/volatile/tmp.
[ OK ] Reached target Local File Systems.
Starting Create Volatile Files and Directories...
[ OK ] Finished Create Volatile Files and Directories.
[ 5.060091] pfeng: loading out-of-tree module taints kernel.
[ 5.087732] pfeng 46000000.pfe: PFEng ethernet driver loading ...
[ 5.087749] pfeng 46000000.pfe: Version: RTM 1.0.0
[ 5.087753] pfeng 46000000.pfe: Multi instance support: disabled (standalone)
[ 5.087756] pfeng 46000000.pfe: Compiled by: 10.2.0
[ 5.087783] pfeng 46000000.pfe: Cbus addr 0x46000000 size 0x1000000
[ 5.087791] pfeng 46000000.pfe: nxp,fw-class-name: s32g_pfe_class.fw
[ 5.087796] pfeng 46000000.pfe: nxp,fw-util-name: s32g_pfe_util.fw
[ 5.087848] pfeng 46000000.pfe: irq 'hif0' : 58
[ 5.087862] pfeng 46000000.pfe: irq 'hif1' : 59
[ 5.087874] pfeng 46000000.pfe: irq 'hif2' : 60
[ 5.087879] pfeng 46000000.pfe: HIF channels mask: 0x0007
[ 5.087890] pfeng 46000000.pfe: netif name: pfe0
[ 5.087896] pfeng 46000000.pfe: DT mac addr: 00:01:be:be:ef:11
[ 5.087903] pfeng 46000000.pfe: netif(pfe0) mode: std
[ 5.087908] pfeng 46000000.pfe: netif(pfe0) EMAC: 0
[ 5.087914] pfeng 46000000.pfe: netif(pfe0) HIFs: count 1 map 01
[ 5.087923] pfeng 46000000.pfe: EMAC0 interface mode: 4
[ 5.088060] pfeng 46000000.pfe: PFE port coherency enabled, mask 0x1e
[ 5.088249] pfeng 46000000.pfe: Clocks: sys=300MHz pe=600MHz
[ 5.088263] pfeng 46000000.pfe: Interface selected: EMAC0: 0x4 EMAC1:
0xfffff
fff EMAC2: 0xffffffff
[ 5.120057] pfeng 46000000.pfe: PFE controller reset done
[ 5.120169] pfeng 46000000.pfe: TX clock on EMAC0 for interface sgmii
install
ed
[ 5.120219] pfeng 46000000.pfe: RX clock on EMAC0 for interface sgmii
install
ed
[ 5.120556] pfeng 46000000.pfe: assigned reserved memory node
pfebufs@3400000
0
[ 5.129221] pfeng 46000000.pfe: assigned reserved memory node
pfebufs@34
080000
Starting Network Time Synchronization...
[ 5.129320] pfeng 46000000.pfe: assigned reserved memory node
pfebufs@8320000
0
[ 5.129353] pfeng 46000000.pfe: assigned reserved memory node
pfebufs@83
5e0000
Starting Update UTMP about System Boot/Shutdown...
[ 5.137731] pfeng 46000000.pfe: Firmware: CLASS s32g_pfe_class.fw [39860
byte
s]
[ 5.137746] pfeng 46000000.pfe: Firmware: UTIL s32g_pfe_util.fw [19940 bytes]
32m OK ] Finished Update UTMP about System Boot/Shutdown.
[ 5.137765] pfeng 46000000.pfe: PFE CBUS p0x46000000 mapped @
v0xffffffc01300
0000
[ 5.137781] pfeng 46000000.pfe: HW version 0x101
[ 5.137788] pfeng 46000000.pfe: Silicon S32G3
[ 5.137795] pfeng 46000000.pfe: Fail-Stop mode disabled
[ 5.139219] pfeng 46000000.pfe: BMU1 buffer base: p0xc0000000
[ 5.139318] pfeng 46000000.pfe: BMU2 buffer base: p0x34000000 (0x80000 bytes)
[ 5.140631] pfeng 46000000.pfe: register IRQ 62 by name 'PFE BMU IRQ'
[ 5.173797] pfeng 46000000.pfe: BMU_EMPTY_INT (BMU @ p0x(____ptrval____)).
Po
ol ready.
[ 5.173819] pfeng 46000000.pfe: BMU_EMPTY_INT (BMU @ p0x(____ptrval____)).
Po
ol ready.
[ 5.173857] pfeng 46000000.pfe: Firmware .elf detected
32m OK ] Started Network Time Synchronization 5.173864] pfeng
46000000.pfe:
Uploading CLASS
firmware
0m.
[ 5.173871] pfeng 46000000.pfe: Selected FW loading OPs to load 8 PEs in
para
llel
[ 5.341346] pfeng 46000000.pfe: pfe_ct.h file
version"e1cb376b67fa4d1de800b13
2b328b42c"
[ 5.383695] pfeng 46000000.pfe: [FW VERSION] 1.3.0, Build: May 31 2022,
08:22
:22 (), ID: 0x31454650
[ 5.384015] pfeng 46000000.pfe: SAFETY instance created
32m OK ] Reached target System Initialization 5.384025] pfeng
46000000.pfe:
Watchdog instance
created
0m.
[ 5.384038] pfeng 46000000.pfe: Uploading UTIL firmware
[ 5.384043] pfeng 46000000.pfe: Selected FW loading OPs to load 1 PEs in
para
llel
32m OK ] Started Daily Cleanup of Temporary Directories.
[ 5.396834] pfeng 46000000.pfe: pfe_ct.h file
version"e1cb376b67fa4d1de800b13
2b328b42c"
[ 5.410446] pfeng 46000000.pfe: VLAN ID incorrect or not set. Using default
V
LAN ID = 0x01.
32m OK ] Reached target System Time Set.
[ 5.410452] pfeng 46000000.pfe: VLAN stats size incorrect or not set. Using
d
efault VLAN stats size = 20.
[ 5.410544] pfeng 46000000.pfe: Fall-back bridge domain @ 0x20000a34 (class)
[ 5.410551] pfeng 46000000.pfe: Default bridge domain @ 0x20000a2c (class)
[ 5.416680] pfeng 46000000.pfe: Routing table created, Hash Table @
p0x340800
00, Pool @ p0x34088000
(65536 bytes)
[ 5.416989] pfeng 46000000.pfe: Feature err051211_workaround: DISABLED
32m OK ] Reached target System Time Synchronized.
[ 5.418364] pfeng 46000000.pfe: MDIO bus 0 disabled: Not found in DT
[ 5.418370] pfeng 46000000.pfe: MDIO bus 1 disabled: No EMAC
[ 5.418374] pfeng 46000000.pfe: MDIO bus 2 disabled: No EMAC
32m OK ] Started Daily rotation of log files.
[ 5.418705] pfeng 46000000.pfe: HIF0 enabled
[ 5.418967] pfeng 46000000.pfe: HIF1 enabled
[ 5.419229] pfeng 46000000.pfe: HIF2 enabled
[ 5.419235] pfeng 46000000.pfe: HIF3 not configured, skipped
32m OK ] Reached target Timers.
[ 5.424471] pfeng 46000000.pfe pfe0: registered
[ 5.424496] pfeng 46000000.pfe pfe0: Subscribe to HIF0
32m OK ] Listening on D-Bus System Message Bus[ 5.425044] pfeng
46000000.pf
e pfe0: Enable HIF0
Socket.
[ 5.425207] pfeng 46000000.pfe pfe0: setting MAC addr: 00:01:be:be:ef:11
[ 5.425234] pfeng 46000000.pfe pfe0: PTP HW addend 0x80000000, max_adj
c
onfigured to 46566128 ppb
Starting sshd.socket.
[ 5.425243] pfeng 46000000.pfe: IEEE1588: Input Clock: 200000000Hz, Output:
1
00000000Hz, Accuracy: 10.0ns
[ 5.431115] pfeng 46000000.pfe pfe0: Registered PTP HW clock successfully on
EMAC0
[ OK ] Listening on sshd.socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started Job spooling tools.
[ OK ] Started Periodic Command Scheduler.
[ OK ] Started D-Bus System Message Bus.
[ OK ] Started A minimalistic net…Pv4, rdisc and DHCPv6 support.
Starting IPv6 Packet Filtering Framework...
Starting IPv4 Packet Filtering Framework...
[ OK ] Started irqbalance daemon.
[ OK ] Started Hardware RNG Entropy Gatherer Daemon.
[ OK ] Started strongSwan IPsec I…IKEv2 daemon using ipsec.conf.
[ 6.625086] random: crng init done
[ 6.625101] random: 7 urandom warning(s) missed due to ratelimiting
[ OK ] Started System Logging Service.
Starting User Login Management...
Starting The Xen xenstore...
Starting OpenSSH Key Generation...
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished IPv6 Packet Filtering Framework.
[ OK ] Finished IPv4 Packet Filtering Framework.
[ OK ] Reached target Network (Pre).
Starting Network Service...
[FAILED] Failed to start The Xen xenstore.
See 'systemctl status xenstored.service' for details.
[DEPEND] Dependency failed for xen-…des, JSON configuration stub).
[DEPEND] Dependency failed for Xenc…guest consoles and hypervisor.
[DEPEND] Dependency failed for Xend…p guests on boot and shutdown.
[DEPEND] Dependency failed for qemu for xen dom0 disk backend.
[ OK ] Started Network Service.
[ OK ] Finished OpenSSH Key Generation.
[ OK ] Started User Login Management.
Starting Network Name Resolution...
Starting Xen-watchdog - run xen watchdog daemon...
[ OK ] Started Xen-watchdog - run xen watchdog daemon.
[ OK ] Started Network Name Resolution.
[ OK ] Reached target Network.
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Started NFS status monitor for NFSv2/3 locking..
[ OK ] Started Respond to IPv6 Node Information Queries.
[ OK ] Started Network Router Discovery Daemon.
Starting Permit User Sessions...
[ OK ] Started Xinetd A Powerful Replacement For Inetd.
[ OK ] Finished Permit User Sessions.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on hvc0.
[ OK ] Started Serial Getty on ttyLF0.
[ OK ] Reached target Login Prompts.
[ OK ] Reached target Multi-User System.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Finished Update UTMP about System Runlevel Changes.
33.Auto Linux vb3 3t.LFs32g399aevb3 hvc0
>Some extra information about xenstore:
root@s32g399aevb3:~# systemctl status xenstored.service
* xenstored.service - The Xen xenstore
Loaded: loaded (/lib/systemd/system/xenstored.service; enabled; vendor pre>
Active: failed (Result: protocol) since Wed 2020-12-16 17:25:20 UTC; 6min >
Process: 182 ExecStartPre=/bin/grep -q control_d /proc/xen/capabilities (co>
Process: 186 ExecStart=/etc/xen/scripts/launch-xenstore (code=exited, statu>
Main PID: 186 (code=exited, status=0/SUCCESS)
Dec 16 17:25:20 s32g399aevb3 systemd[1]: Starting The Xen xenstore...
Dec 16 17:25:20 s32g399aevb3 launch-xenstore[186]: Starting /usr/sbin/xenstored>
Dec 16 17:25:20 s32g399aevb3 launch-xenstore[193]: FATAL: Failed to open connec>
Dec 16 17:25:20 s32g399aevb3 systemd[1]: xenstored.service: Failed with result >
Dec 16 17:25:20 s32g399aevb3 systemd[1]: Failed to start The Xen xenstore.
>Any idea of how can I fix that? Thank you so much for the support
Best regards
Youssef El Mesdadi
-----Ursprüngliche Nachricht-----
Von: Julien Grall <julien@xxxxxxx>
Gesendet: Dienstag, 17. Januar 2023 15:38
An: El Mesdadi Youssef ESK UILD7 <youssef.elmesdadi@xxxxxx>;
xen-devel@xxxxxxxxxxxxxxxxxxxx
Cc: Stefano Stabellini <sstabellini@xxxxxxxxxx>
Betreff: Re: AW: Xenalyze on ARM ( NXP S32G3 with Cortex-A53)
On 13/01/2023 12:56, El Mesdadi Youssef ESK UILD7 wrote:
> Hello Julien,
Hi,
>>>> xentrace should work on upstream Xen. What did you version did you try?
>
> While building my image using the BSP-linux of NXP, the version that was
> downloaded is Xen 4.14.
Do you know where the source are downloaded from?
>
>
>>>> Can you also clarify the error you are seen?
>
> The error I receive while tipping xentrace is: Command not found.
"Command not found" means the program hasn't been installed.
> I assume in this Xen version, Xentrace is not compatible with ARM
> architecture
The support for xentrace on Arm has been added around Xen 4.12. So it should
work for Xen 4.14 (even though I don't recommend using older release).
I would suggest to check how you are building the tools and which package will
be installed.
>
> My question is, is there any new version of Xen that supports Xentrace on
> ARM? If yes how could I install it? Because Xen.4.14 was installed
> automatically by typing this ( DISTRO_FEATURES_append += "xen") in the
> local.conf file while creating my image.
I am not familiar with the BSP-linux of NXP as this is not a project maintained
by Xen Project.
If you need support for it, then I would suggest to discuss with NXP directly.
>
> Or is there any source on Xentrace that is compatible with ARM on GitHub,
> that I could download and compile myself?
Even if the hypervisor is Xen, you seem to use code provided by an external
entity. I can't advise on the next steps without knowing the modification that
NXP made in the hypervisor.
>
>>>> Yes if you assign (or provide para-virtualized driver) the
>>>> GPIO/LED/Can-Interface to the guest.
>
> Is there any tutorial that could help me create those drivers? And how
> complicated is that, to create them?
I am not aware of any tutorial. Regarding the complexity, it all depends on
what exactly you want to do.
> Or can they be assigned just with PCI-Passthrough?
PCI passthrough is not yet supported on Arm. That said, I was not expecting the
GPIO/LED/Can-interface to be PCI devices.
If they are platform devices (i.e non-PCI devices), then you could potentially
directly assign them to *one* guest (this would not work if you need to share
them).
I wrote potentially because if the device is DMA-capabable, then the device
must be behind an IOMMU.
Cheers,
--
Julien Grall
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |