Re: [Xen-devel] xhci_hcd intterrupt affinity in Dom0/DomU limited to single interrupt

[Justin Acker <ackerj68@xxxxxxxxx>]

On Fri, 2015-09-11 at 04:03 -0600, Jan Beulich wrote:
> >>> On 10.09.15 at 18:20, <ackerj67@xxxxxxxxx> wrote:
> > On Wed, 2015-09-09 at 00:48 -0600, Jan Beulich wrote:
> >> >>> On 08.09.15 at 18:02, <ackerj67@xxxxxxxxx> wrote:
> >> > I believe the driver does support use of multiple interrupts based on
> >> > the previous explanation of the lspci output where it was established
> >> > that the device could use up to 8 interrupts which is what I see on bare
> >> > metal.
> >> 
> >> Where is the proof of that? All I've seen is output like this
> >> 
> >>     Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
> >> 
> >> which says that one out of eight interrupts is being used. And
> >> if in the native case this would indeed be the case, I don't think
> >> you've provided complete hypervisor and kernel logs for the
> >> Xen case so far, which would allow us to look for respective error
> >> indications. And this (ignoring the line wrapping, which makes
> >> things hard to read - it would be appreciated if you could fix
> >> your mail client)...
> >> 
> >> > Bare metal:
> >> > 
> >> > cat /proc/interrupts 
> >> >            CPU0       CPU1       CPU2       CPU3       CPU4       CPU5
> >> > CPU6       CPU7       
> >> >   0:         36          0          0          0          0          0
> >> > 0          0  IR-IO-APIC-edge      timer
> >> >[...]
> >> >  27:     337125      47893     708965       4049   53940667     263303
> >> > 87847       4958  IR-PCI-MSI-edge      xhci_hcd
> >> 
> >> ... also shows just a single interrupt being in use.
> > 
> > Kernel logs for native and Dom0 with 'debug' appended to grub. xl-dmesg
> > with log_lvl=all guest_loglvl=all set. Please let me know if there are
> > other logs or log levels that I should provide. 
>
> The native kernel log supports there only being a single interrupt
> in use. I'm still not seeing any proof of your claim for this to be
> different. Did you double check lspci output in the native case?
>
> Jan

Jan,

I think the lspci -v output is the same in both cases with the exception of the xhci_pci which is not present in the Native case lspci -v output.  xhci_pci is built into the kernel. The same kernel/system is used with this system when booted with Dom0 and native cases. I could rebuild the kernel without it and see what happens? 

Native:

00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) (prog-if 30 [XHCI])
	Subsystem: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI
	Flags: bus master, medium devsel, latency 0, IRQ 27
	Memory at f7e20000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [70] Power Management version 2
	Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
	Kernel driver in use: xhci_hcd



Dom0:

00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) (prog-if 30 [XHCI])
	Subsystem: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI
	Flags: bus master, medium devsel, latency 0, IRQ 76
	Memory at f7e20000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [70] Power Management version 2
	Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci


cat /boot/config-3.18.1-1.fc20.x86_64 | grep XHCI
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PCI=y



_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel