Re: [Xen-devel] High CPU temp, suspend problem - xen 4.1.5-pre, linux 3.7.x

[Andrew Cooper <andrew.cooper3@xxxxxxxxxx>]

On 26/03/2013 13:50, Marek Marczykowski wrote:
> On 26.03.2013 14:11, Jan Beulich wrote:
>>>>> On 26.03.13 at 13:17, Marek Marczykowski 
>>>>> <marmarek@xxxxxxxxxxxxxxxxxxxxxx> wrote:
>>> Finally got serial console :)
>>> The debug=y problem is (actually at resume):
>>> (XEN) Assertion 'test_bit(vector, cfg->used_vectors)' failed at 
>>> io_apic.c:542
>>> (XEN) ----[ Xen-4.1.5-rc1  x86_64  debug=y  Tainted:    C ]----
>>> (XEN) CPU:    0
>>> (XEN) RIP:    e008:[<ffff82c48015e288>] 
>>> smp_irq_move_cleanup_interrupt+0x1c3/0x23d
>>> (XEN) RFLAGS: 0000000000010046   CONTEXT: hypervisor
>>> (XEN) rax: 0000000000000000   rbx: 00000000000000e9   rcx: ffff82c48029ff18
>>> (XEN) rdx: 00000000000000e9   rsi: 000000000000002a   rdi: ffff830421060538
>>> (XEN) rbp: ffff82c48029ff08   rsp: ffff82c48029feb8   r8:  ffff88041820eb60
>>> (XEN) r9:  0000000000000000   r10: 0000000000007ff0   r11: 0000000000000000
>>> (XEN) r12: ffff830421080250   r13: ffff830421060534   r14: ffff82c48029ff18
>>> (XEN) r15: ffff82c4802dd9e0   cr0: 000000008005003b   cr4: 00000000000026f0
>>> (XEN) cr3: 0000000300b81000   cr2: ffff880402070198
>>> (XEN) ds: 0000   es: 0000   fs: 0000   gs: 0000   ss: 0000   cs: e008
>>> (XEN) Xen stack trace from rsp=ffff82c48029feb8:
>>> (XEN)    0000000000000000 000000000000e030 ffff82c48029ff18 ffff82c4802dd9e0
>>> (XEN)    ffff8802cac3c7c0 00000000ffff3729 00000000ffff3729 000000013fff3728
>>> (XEN)    ffffffff81b907c0 00000000ffff3729 00007d3b7fd600c7 ffff82c48014de60
>>> (XEN)    00000000ffff3729 ffffffff81b907c0 000000013fff3728 00000000ffff3729
>>> (XEN)    ffffffff81a01e18 00000000ffff3729 0000000000000000 0000000000007ff0
>>> (XEN)    0000000000000000 ffff88041820eb60 ffff8803fd1820a8 ffffffff81b90a88
>>> (XEN)    000000000000002a 000000000000002a 00000000ffff372a 0000002000000000
>>> (XEN)    ffffffff8105dd5a 000000000000e033 0000000000000246 ffffffff81a01db8
>>> (XEN)    000000000000e02b 0000000000000000 0000000000000000 0000000000000000
>>> (XEN)    0000000000000000 0000000000000000 ffff8300ca9a0000 0000000000000000
>>> (XEN)    0000000000000000
>>> (XEN) Xen call trace:
>>> (XEN)    [<ffff82c48015e288>] smp_irq_move_cleanup_interrupt+0x1c3/0x23d
>>> (XEN)
>>> (XEN)
>>> (XEN) ****************************************
>>> (XEN) Panic on CPU 0:
>>> (XEN) Assertion 'test_bit(vector, cfg->used_vectors)' failed at 
>>> io_apic.c:542
>>> (XEN) ****************************************
>> To make sense of this, we need to know the register (and maybe
>> stack) allocation at this point, to know which vector it was that
>> triggered the assertion. You can either do this analysis for us, or
>> point us at the xen-syms binary matching the xen.gz you used.
> "info scope smp_irq_move_cleanup_interrupt" said vector is in %rbx, so 0xe9.
>
>> From the register values, the most likely candidates are vector 0xe9
>> and 0x2a. The former having two registers set to this value seems
>> more likely from than angle, but vectors in the 0xe? range should
>> never end up in smp_irq_move_cleanup_interrupt().
>>
>> And if it's the 0x2a one, then we'd need to know what IRQ it was
>> last used for. That can't be reconstructed from the data above, so
>> would require you being able to reproduce this and adding some
>> instrumentation to the code.
>>
>> Jan
>>
>

Could it be something to do with switching virtual wire mode, and having
PIC compatibility stuff left in the IO-APIC after leaving the BIOS but
before starting back up again?

Looking at the stack dump, there is an extra exception frame under what
is printed by the assertion failure.

0000002000000000 TRAP_syscall
ffffffff81a01db8 guest kernel addr
0000000000000246 FLAGS
000000000000e033 FLAT_RING3_CS64
ffffffff8105dd5a guest kernel addr
000000000000e02b FLAT_RING3_SS{64,32}

So it appears that we are already executing a guest (presumably dom0) by the 
time this assertion occurs.  From the serial, is there any indication that dom0 
has started up again?

I would have thought that we should have successfully reset the IO-APIC back up 
properly before we would ever get back around to executing dom0.

~Andrew


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel