[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] no-carrier on qlogic 8242 10gig with linux 3.x running xen


  • To: xen-devel@xxxxxxxxxxxxxxxxxxx
  • From: Kristoffer Harthing Egefelt <k@xxxxxxx>
  • Date: Wed, 28 Mar 2012 02:55:50 -0700 (PDT)
  • Delivery-date: Wed, 28 Mar 2012 09:56:21 +0000
  • List-id: Xen developer discussion <xen-devel.lists.xen.org>

This is ip a showing no-carrier, even if the NIC is upped with ip link set
dev eth0 up

*ip a *
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,PROMISC,UP> mtu 1500 qdisc
pfifo_fast state DOWN qlen 1000
    link/ether 24:b6:fd:64:1e:45 brd ff:ff:ff:ff:ff:ff
3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,PROMISC,UP> mtu 1500 qdisc
pfifo_fast state DOWN qlen 1000
    link/ether 24:b6:fd:64:1e:46 brd ff:ff:ff:ff:ff:ff

*This is ifconfig:*
eth0      Link encap:Ethernet  HWaddr 24:b6:fd:64:1e:45  
          UP BROADCAST PROMISC MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:175 

*Interrupt 175 does not exist in /proc/interrupts*

*This is dmesg while loading the qlcnic driver*
[   12.009860] qlcnic 0000:03:00.0: phy port: 0 switch_mode: 0,
[   12.009862]  max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
[   12.009864]  max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0x6affae
[   12.025831] qlcnic 0000:03:00.0: failed card response code:0x10
[   12.025889] qlcnic 0000:03:00.0: Can't get template size 16
[   12.025893] qlcnic 0000:03:00.0: firmware v4.7.83
[   12.057837] qlcnic: 24:b6:fd:64:1e:45: QME8242-k 10GbE Dual Port
Mezzanine Card Board Chip rev 0x54
[   12.058243] qlcnic 0000:03:00.0: using msi-x interrupts
[   12.058810] qlcnic 0000:03:00.0: eth0: XGbE port initialized
[   12.058844] xen: registering gsi 38 triggering 0 polarity 1
[   12.058856] xen_map_pirq_gsi: returning irq 38 for gsi 38
[   12.058859] xen: --> pirq=38 -> irq=38 (gsi=38)
[   12.058863] Already setup the GSI :38

*Interrupt 38 does not exist in /proc/interrupts*

This is before any network configuration is run.
/etc/network/interfaces is disabled - I run openvswitch and do all network
configuration in some custom scripts. 

Without xen it works - the irq's exist.

--
View this message in context: 
http://xen.1045712.n5.nabble.com/no-carrier-on-qlogic-8242-10gig-with-linux-3-x-running-xen-tp5597283p5599996.html
Sent from the Xen - Dev mailing list archive at Nabble.com.

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.