Xen project Mailing List

On Tue, Feb 26, 2013 at 3:50 PM, Joern Bredereck <jb@xxxxxxxxxxxxxx> wrote:

Did you just stop the "cobian backup service" or did you disable it? Just stopping it won't cut it, because after the next reboot the service would start again automatically unless you disable it.

How long did you wait until you logged in? I'm not sure, but I had the best results when I let the installer do it's thing without logging in until XenCenter confirmed that the tools are running and the network tab reported the correct IP address.

Am 26.02.2013 um 18:48 schrieb Alejandro Flores <alejandrorflores@xxxxxxxxx>:

> Hey Joern,
>
> I have Cobian Backup, so, I uninstalled Xentools, stopped the cobian backup service, and tried again, but no luck, after some reboots, it is now, again, stopped on the wizzard window with:
>
> Drivers: installing
> Guest Agent: installing
>
> ..
> What now?
>
> Thanks for your help!
>
>
>
>
> On Tue, Feb 26, 2013 at 11:19 AM, Joern Bredereck <jb@xxxxxxxxxxxxxx> wrote:
> I had the same problem a couple of weeks ago.
>
> if the Install Wizard still shows up that means that the drivers are not completely installed yet. In my case a backup agent that belongs to the backup software "shadow protect" blocked the VSS (volume shadow service). Consequently the Xen Guest Tool Installer could not install it's VSS drivers and therefore the whole installation hung (at least I assume that's what happened).
>
> I could resolv this issue by deactivating the backup service before starting the guest tool installation.
>
> Regards,
> Joern
>
>
>
> On Feb 26, 2013, at 3:11 PM, Alejandro Flores <alejandrorflores@xxxxxxxxx> wrote:
>
>> Hey,
>>
>> After a lot of reboots, installs, etc.. etc... it's with the Xentools install wizard window opened for a loooong time with:
>> Drivers: installing
>> Guest Agent: installing
>>
>> But already installed it earlier! What now? :)
>>
>> Regards,
>>
>>
>> On Tue, Feb 26, 2013 at 9:35 AM, Alejandro Flores <alejandrorflores@xxxxxxxxx> wrote:
>> Hey Jörn,
>>
>> I'll let it reboots then, will count how many times it will happen.
>> Yesterday was at least 4 reboots.
>> I'll let you know if it stops or not!!
>>
>> Regards,
>>
>>
>> On Tue, Feb 26, 2013 at 9:17 AM, Joern Bredereck <jb@xxxxxxxxxxxxxx> wrote:
>>
>> Are you sure the installation of the xentools has been finished? Installation of the tools requires several (in my experience up to 5) reboots, before all drivers and tools are being installed completely.
>>
>> Regards,
>> Jörn
>>
>>
>> On Feb 26, 2013, at 1:12 PM, Alejandro Flores <alejandrorflores@xxxxxxxxx> wrote:
>>
>>> Hello there!
>>>
>>> I'm having this strange problem after convert/migration p2v of my windows 2008 server. After migration, it was OK, but then I installed xentools and the vm now keeps rebooting all the time. I can login, and after a while, it makes a logoff for reboot, over and over again.
>>>
>>> It's a known problem?
>>>
>>> I'm using XCP 1.6
>>>
>>> Regards!
>>> --
>>>
>>> Alejandro Flores
>>> Office: 81 3031-4595
>>> Mobile: 81 8210-0412
>>> http://www.triforsec.com.br/
>>> http://www.dialtelecom.com.br/
>>> _______________________________________________
>>> Xen-api mailing list
>>> Xen-api@xxxxxxxxxxxxx
>>> http://lists.xen.org/cgi-bin/mailman/listinfo/xen-api
>>
>>
>>
>>
>> --
>>
>> Alejandro Flores
>> Office: 81 3031-4595
>> Mobile: 81 8210-0412
>> http://www.triforsec.com.br/
>> http://www.dialtelecom.com.br/
>>
>>
>>
>> --
>>
>> Alejandro Flores
>> Office: 81 3031-4595
>> Mobile: 81 8210-0412
>> http://www.triforsec.com.br/
>> http://www.dialtelecom.com.br/
>
>
>
>
> --
>
> Alejandro Flores
> Office: 81 3031-4595
> Mobile: 81 8210-0412
> http://www.triforsec.com.br/
> http://www.dialtelecom.com.br/

--

Alejandro Flores
Office: 81 3031-4595
Mobile: 81 8210-0412
http://www.triforsec.com.br/
http://www.dialtelecom.com.br/

Re: [Xen-API] Problem after migration