[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Xen-users] [Xen-devel] Cannot start Fedora 19 HVM domU with VGA passthru
On 18/07/2013 18:29, Gordan Bobic wrote: On Thu, 18 Jul 2013 18:20:08 +0800, "Singapore Citizen Mr. Teo En Ming (Zhang Enming)" <singapore.mr.teo.en.ming@xxxxxxxxx> wrote:On 18/07/2013 18:09, Gordan Bobic wrote:On Thu, 18 Jul 2013 18:07:27 +0800, "Singapore Citizen Mr. Teo En Ming (Zhang Enming)" <singapore.mr.teo.en.ming@xxxxxxxxx> wrote:On 18/07/2013 16:46, Gordan Bobic wrote:On Thu, 18 Jul 2013 16:37:34 +0800, "Singapore Citizen Mr. Teo En Ming (Zhang Enming)" <singapore.mr.teo.en.ming@xxxxxxxxx> wrote:Although Fedora 19 HVM domU with VGA passthrough cannot start, Debian7.1.0 amd64 HVM domU with VGA passthrough can start. In Debian 7.1.0amd64 HVM domU with VGA passthrough, Intel HD Graphics 4600 is listed in lspci -vvv. Please refer to lspci.txt. It is strange that no kernel module is being loaded for Intel HD Graphics 4600. There is no "Kerneldriver in use" statement after VGA compatible controller: Intel Corporation Haswell Integrated Graphics Controller (rev 06) (prog-if 00 [VGA controller]). No kernel driver is seen in lsmod. Please refer to lsmod.txt When I tried to load the kernel module by executing "modprobe i915", it complains "no such device". ERROR: could not insert 'i915': No such deviceSo is my Intel HD Graphics 4600 VGA Passthrough to Debian 7.1.0 amd64 HVM domU considered successful since the i915 driver cannot be loaded?Thank you very much.If you have a driver in dom0 claiming the device (other than the xen-pciback driver), you cannot pass through that device. If you do lspci -ccc on F19 and you see the driver in use for that device being something other thanxen-pciback, that would explain why you can't pass it through.Also, did you first do xl pci-assignable-add for that device? This attemptsto detach the device from it's current driver but doesn't always workespecially for GPUs. The only solution is blacklist the driver for the device in dom0. The downside is that you cannot run a GUI in dom0 on thatdevice.I cannot start Fedora 19 HVM domU with VGA passthrough at all. Could you advise me on the workaround? As for the Intel HD Graphics (i915) driver, I have it blacklisted in /etc/modprobe.d/blacklist.conf already. Please refer to attached blacklist.conf.Have you confirm that no other driver is bound to the device in lspci -vvv? Also what version of Xen are you running on each of the distros, and whichdom0 kernel?I have checked "lsmod | grep i915" and the command doesn't return anything, which means the kernel module i915 is not loaded in dom0.Check lspci -vvv,find the device in the output and look for the lines that say:Kernel driver in use: Kernel modules: The kernel driver might not be called the same thing in both kernels.I am running Xen 4.4-unstable changeset 27238 with Linux kernel 3.11.0-rc1 on a Ubuntu 13.04 host.And on F19? Gordan _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxx http://lists.xen.org/xen-devel Dear Gordan,I have checked lspci -vvv in Ubuntu 13.04 dom0 and the Kernel driver in use is pciback for Intel HD Graphics 4600 IGD. As for Fedora 19 HVM domU, I don't know because I cannot start it. -- Yours sincerely, Singapore Citizen Mr. Teo En Ming (Zhang Enming) _______________________________________________ Xen-users mailing list Xen-users@xxxxxxxxxxxxx http://lists.xen.org/xen-users
|
Lists.xenproject.org is hosted with RackSpace, monitoring our |