[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] [Xen-devel] PCI passthrough problems after legacy update of xen 4.1



Ok, I have some progress. It tried also with the device I had always managed to get through, the radeon 7790 gpu. This worked equally well with both versions of pciif.py. However, it turned out that with the changed version, if I pass the gpu first in the pci = [ ... ] list, the other devices also gets through. This was not the case with the original version of pciif.py.

If (and only if) i order the passthrough list in the config file so that it says

pci = [ '41:00.0', '41:00.1', '04:00.0' ]

(This corresponds to GPU, HDMI audio, USB at irqs 16, 17, 19) - then passthrough of all devices works with the new version of pciif.py ("if dev.irq:"), but not with the old version ("if not self.vm.info.is_hvm() and dev.irq:"). So the second failure seemingly has to do with some property set or checked only for the first passed through device. Logs follow:

WORKING setup:
pci = [ '41:00.0', '41:00.1', '04:00.0' ]
NEW pciif.py (if dev.irq)

xend.log:
[2013-05-02 22:54:38 7863] DEBUG (pciif:169) Reconfiguring PCI device 0000:41:00.0.
[2013-05-02 22:54:38 7863] INFO (pciquirk:92) NO quirks found for PCI device [1002:665c:1458:2269]
[2013-05-02 22:54:38 7863] DEBUG (pciquirk:135) Permissive mode NOT enabled for PCI device [1002:665c:1458:2269]
[2013-05-02 22:54:38 7863] DEBUG (pciif:320) pci: enabling ioport 0xe000/0x100
[2013-05-02 22:54:38 7863] DEBUG (pciif:334) pci: enabling iomem 0xa0000000/0x10000000 pfn 0xa0000/0x10000
[2013-05-02 22:54:38 7863] DEBUG (pciif:334) pci: enabling iomem 0x9f800000/0x800000 pfn 0x9f800/0x800
[2013-05-02 22:54:38 7863] DEBUG (pciif:334) pci: enabling iomem 0xbffc0000/0x40000 pfn 0xbffc0/0x40
[2013-05-02 22:54:38 7863] DEBUG (pciif:334) pci: enabling iomem 0xbffa0000/0x20000 pfn 0xbffa0/0x20
[2013-05-02 22:54:38 7863] DEBUG (pciif:351) pci: enabling irq 16
[2013-05-02 22:54:38 7863] DEBUG (XendDomainInfo:893) XendDomainInfo.pci_device_configure: ['pci', ['dev', ['slot', '0x00'], ['domain', '0x0000'], ['key', '41:00.1'], ['bus', '0x41'], ['vdevfn', '0x100'], ['func', '0x1'], ['uuid', 'e94457db-ac50-04a3-216f-9fb6c8aab1f1']], ['state', 'Initialising'], ['sub_state', 'Booting']]
[2013-05-02 22:54:38 7863] DEBUG (XendDomainInfo:779) XendDomainInfo.hvm_pci_device_insert: {'devs': [{'slot': '0x00', 'domain': '0x0000', 'key': '41:00.1', 'bus': '0x41', 'vdevfn': '0x100', 'func': '0x1', 'uuid': 'e94457db-ac50-04a3-216f-9fb6c8aab1f1'}], 'states': ['Initialising']}
[2013-05-02 22:54:38 7863] DEBUG (XendDomainInfo:790) XendDomainInfo.hvm_pci_device_insert_dev: {'slot': '0x00', 'domain': '0x0000', 'key': '41:00.1', 'bus': '0x41', 'vdevfn': '0x100', 'func': '0x1', 'uuid': 'e94457db-ac50-04a3-216f-9fb6c8aab1f1'}
[2013-05-02 22:54:38 7863] DEBUG (XendDomainInfo:811) XendDomainInfo.hvm_pci_device_insert_dev: 0000:41:00.1@100,msitranslate=1,power_mgmt=1
[2013-05-02 22:54:38 7863] DEBUG (XendDomainInfo:815) pci: assign device 0000:41:00.1@100,msitranslate=1,power_mgmt=1
[2013-05-02 22:54:38 7863] INFO (image:538) signalDeviceModel:restore dm state to running
[2013-05-02 22:54:38 7863] DEBUG (pciif:169) Reconfiguring PCI device 0000:41:00.1.
[2013-05-02 22:54:39 7863] INFO (pciquirk:92) NO quirks found for PCI device [1002:0002:1458:0002]
[2013-05-02 22:54:39 7863] DEBUG (pciquirk:135) Permissive mode NOT enabled for PCI device [1002:0002:1458:0002]
[2013-05-02 22:54:39 7863] DEBUG (pciif:334) pci: enabling iomem 0xbff9c000/0x4000 pfn 0xbff9c/0x4
[2013-05-02 22:54:39 7863] DEBUG (pciif:351) pci: enabling irq 17
[2013-05-02 22:54:39 7863] DEBUG (XendDomainInfo:893) XendDomainInfo.pci_device_configure: ['pci', ['dev', ['slot', '0x00'], ['domain', '0x0000'], ['key', '04:00.0'], ['bus', '0x04'], ['vdevfn', '0x100'], ['func', '0x0'], ['uuid', 'fe6ebcc1-2dcc-7337-c98e-88250cb78896']], ['state', 'Initialising'], ['sub_state', 'Booting']]
[2013-05-02 22:54:39 7863] DEBUG (XendDomainInfo:779) XendDomainInfo.hvm_pci_device_insert: {'devs': [{'slot': '0x00', 'domain': '0x0000', 'key': '04:00.0', 'bus': '0x04', 'vdevfn': '0x100', 'func': '0x0', 'uuid': 'fe6ebcc1-2dcc-7337-c98e-88250cb78896'}], 'states': ['Initialising']}
[2013-05-02 22:54:39 7863] DEBUG (XendDomainInfo:790) XendDomainInfo.hvm_pci_device_insert_dev: {'slot': '0x00', 'domain': '0x0000', 'key': '04:00.0', 'bus': '0x04', 'vdevfn': '0x100', 'func': '0x0', 'uuid': 'fe6ebcc1-2dcc-7337-c98e-88250cb78896'}
[2013-05-02 22:54:39 7863] DEBUG (XendDomainInfo:811) XendDomainInfo.hvm_pci_device_insert_dev: 0000:04:00.0@100,msitranslate=1,power_mgmt=1
[2013-05-02 22:54:39 7863] DEBUG (XendDomainInfo:815) pci: assign device 0000:04:00.0@100,msitranslate=1,power_mgmt=1
[2013-05-02 22:54:39 7863] INFO (image:538) signalDeviceModel:restore dm state to running
[2013-05-02 22:54:39 7863] DEBUG (pciif:169) Reconfiguring PCI device 0000:04:00.0.
[2013-05-02 22:54:39 7863] INFO (pciquirk:92) NO quirks found for PCI device [104c:8241:0000:0000]
[2013-05-02 22:54:39 7863] DEBUG (pciquirk:135) Permissive mode NOT enabled for PCI device [104c:8241:0000:0000]
[2013-05-02 22:54:39 7863] DEBUG (pciif:334) pci: enabling iomem 0xdfef0000/0x10000 pfn 0xdfef0/0x10
[2013-05-02 22:54:39 7863] DEBUG (pciif:334) pci: enabling iomem 0xdfeee000/0x2000 pfn 0xdfeee/0x2
[2013-05-02 22:54:39 7863] DEBUG (pciif:351) pci: enabling irq 19

... all OK and running. The gpu does not initialize unless after reboot of dom0, but that issue was since before.

FAILING setup:
pci = [ '41:00.0', '41:00.1', '04:00.0' ] (as before)
OLD pciif.py (if not ... and dev.irq)

xend.log:
[2013-05-02 22:59:13 9301] DEBUG (XendDomainInfo:811) XendDomainInfo.hvm_pci_device_insert_dev: 0000:41:00.0@100,msitranslate=1,power_mgmt=1
[2013-05-02 22:59:13 9301] DEBUG (XendDomainInfo:815) pci: assign device 0000:41:00.0@100,msitranslate=1,power_mgmt=1
[2013-05-02 22:59:13 9301] DEBUG (image:508) signalDeviceModel: orig_state is None, retrying
[2013-05-02 22:59:13 9301] DEBUG (image:508) signalDeviceModel: orig_state is None, retrying
[2013-05-02 22:59:14 9301] INFO (image:538) signalDeviceModel:restore dm state to running
[2013-05-02 22:59:14 9301] INFO (pciquirk:92) NO quirks found for PCI device [1002:665c:1458:2269]
[2013-05-02 22:59:14 9301] DEBUG (pciquirk:135) Permissive mode NOT enabled for PCI device [1002:665c:1458:2269]
[2013-05-02 22:59:14 9301] DEBUG (pciif:320) pci: enabling ioport 0xe000/0x100
[2013-05-02 22:59:14 9301] DEBUG (pciif:334) pci: enabling iomem 0xa0000000/0x10000000 pfn 0xa0000/0x10000
[2013-05-02 22:59:14 9301] DEBUG (pciif:334) pci: enabling iomem 0x9f800000/0x800000 pfn 0x9f800/0x800
[2013-05-02 22:59:14 9301] DEBUG (pciif:334) pci: enabling iomem 0xbffc0000/0x40000 pfn 0xbffc0/0x40
[2013-05-02 22:59:14 9301] DEBUG (pciif:334) pci: enabling iomem 0xbffa0000/0x20000 pfn 0xbffa0/0x20
[2013-05-02 22:59:14 9301] DEBUG (pciif:351) pci: enabling irq 16
[2013-05-02 22:59:14 9301] INFO (pciquirk:92) NO quirks found for PCI device [1002:0002:1458:0002]
[2013-05-02 22:59:14 9301] DEBUG (pciquirk:135) Permissive mode NOT enabled for PCI device [1002:0002:1458:0002]
[2013-05-02 22:59:14 9301] DEBUG (pciif:334) pci: enabling iomem 0xbff9c000/0x4000 pfn 0xbff9c/0x4
[2013-05-02 22:59:14 9301] DEBUG (pciif:351) pci: enabling irq 17
[2013-05-02 22:59:14 9301] ERROR (XendDomainInfo:2927) XendDomainInfo.initDomain: exception occurred
Traceback (most recent call last):
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2914, in _initDomain
    self._createDevices()
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2395, in _createDevices
    self.pci_device_configure_boot()
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 627, in pci_device_configure_boot
    self.pci_device_configure(dev_sxp, first_dev = first)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 970, in pci_device_configure
    devid = self._createDevice('pci', existing_pci_conf)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2326, in _createDevice
    return self.getDeviceController(deviceClass).createDevice(devConfig)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/server/DevController.py", line 67, in createDevice
    self.setupDevice(config)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/server/pciif.py", line 453, in setupDevice
    self.setupOneDevice(d)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/server/pciif.py", line 353, in setupOneDevice
    allow_access = True)
Error: (22, 'Invalid argument')
[2013-05-02 22:59:14 9301] ERROR (XendDomainInfo:488) VM start failed
Traceback (most recent call last):
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 474, in start
    XendTask.log_progress(31, 60, self._initDomain)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendTask.py", line 209, in log_progress
    retval = func(*args, **kwds)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2930, in _initDomain
    raise VmError(str(exn))
VmError: (22, 'Invalid argument')
[2013-05-02 22:59:14 9301] DEBUG (XendDomainInfo:3071) XendDomainInfo.destroy: domid=39
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2401) Destroying device model
[2013-05-02 22:59:17 9301] INFO (image:615) w8 device model terminated
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2408) Releasing devices
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vif/0
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vif, device = vif/0
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vbd/768
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/768
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vbd/832
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/832
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vbd/5632
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/5632
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vfb/0
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vfb, device = vfb/0
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2406) No device model
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2408) Releasing devices
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vif/0
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vif, device = vif/0
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vbd/768
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/768
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vbd/832
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/832
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:2414) Removing vbd/5632
[2013-05-02 22:59:17 9301] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/5632
[2013-05-02 22:59:17 9301] ERROR (XendDomainInfo:108) Domain construction failed
Traceback (most recent call last):
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 106, in create
    vm.start()
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 474, in start
    XendTask.log_progress(31, 60, self._initDomain)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendTask.py", line 209, in log_progress
    retval = func(*args, **kwds)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2930, in _initDomain
    raise VmError(str(exn))
VmError: (22, 'Invalid argument')

(end of file)

Any other ordering of the pci = [ ... ] list fails as before, but in different ways as shown in my earlier test.

/Andreas


2013/5/2 Andreas Falck <falck.andreas.lists@xxxxxxxxx>
Ok, I changed so that the corresponding first lines of code looks like this:
   
        if dev.irq: 
            rc = xc.physdev_map_pirq(domid = fe_domid,
                                   index = dev.irq,
                                   pirq  = dev.irq)

(only the first line changed)
Then, after restarting xend, I get a different failure on line 346, which is the last line of the above: "VmError: (17, 'File exists')". Full xend.log attached below.

I can also do tests with the one device which I still manage to pass through (a gpu), if I get specific suggestions on what to look for.

/Andreas   

[2013-05-02 20:41:29 19545] DEBUG (XendDomainInfo:811) XendDomainInfo.hvm_pci_device_insert_dev: 0000:04:00.0@100,msitranslate=1,power_mgmt=1
[2013-05-02 20:41:29 19545] DEBUG (XendDomainInfo:815) pci: assign device 0000:04:00.0@100,msitranslate=1,power_mgmt=1
[2013-05-02 20:41:29 19545] DEBUG (image:508) signalDeviceModel: orig_state is None, retrying
[2013-05-02 20:41:29 19545] INFO (image:538) signalDeviceModel:restore dm state to running
[2013-05-02 20:41:30 19545] INFO (pciquirk:92) NO quirks found for PCI device [104c:8241:0000:0000]
[2013-05-02 20:41:30 19545] DEBUG (pciquirk:135) Permissive mode NOT enabled for PCI device [104c:8241:0000:0000]
[2013-05-02 20:41:30 19545] DEBUG (pciif:334) pci: enabling iomem 0xdfef0000/0x10000 pfn 0xdfef0/0x10
[2013-05-02 20:41:30 19545] DEBUG (pciif:334) pci: enabling iomem 0xdfeee000/0x2000 pfn 0xdfeee/0x2
[2013-05-02 20:41:30 19545] ERROR (XendDomainInfo:2927) XendDomainInfo.initDomain: exception occurred

Traceback (most recent call last):
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2914, in _initDomain
    self._createDevices()
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2395, in _createDevices
    self.pci_device_configure_boot()
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 627, in pci_device_configure_boot
    self.pci_device_configure(dev_sxp, first_dev = first)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 970, in pci_device_configure
    devid = self._createDevice('pci', existing_pci_conf)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2326, in _createDevice
    return self.getDeviceController(deviceClass).createDevice(devConfig)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/server/DevController.py", line 67, in createDevice
    self.setupDevice(config)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/server/pciif.py", line 453, in setupDevice
    self.setupOneDevice(d)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/server/pciif.py", line 346, in setupOneDevice
    pirq  = dev.irq)
Error: (17, 'File exists')
[2013-05-02 20:41:30 19545] ERROR (XendDomainInfo:488) VM start failed

Traceback (most recent call last):
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 474, in start
    XendTask.log_progress(31, 60, self._initDomain)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendTask.py", line 209, in log_progress
    retval = func(*args, **kwds)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2930, in _initDomain
    raise VmError(str(exn))
VmError: (17, 'File exists')
[2013-05-02 20:41:30 19545] DEBUG (XendDomainInfo:3071) XendDomainInfo.destroy: domid=19
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2401) Destroying device model
[2013-05-02 20:41:32 19545] INFO (image:615) w8 device model terminated
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2408) Releasing devices
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vif/0
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vif, device = vif/0
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vbd/768
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/768
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vbd/832
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/832
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vbd/5632
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/5632
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vfb/0
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vfb, device = vfb/0
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2406) No device model
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2408) Releasing devices
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vif/0
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vif, device = vif/0
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vbd/768
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/768
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vbd/832
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/832
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:2414) Removing vbd/5632
[2013-05-02 20:41:32 19545] DEBUG (XendDomainInfo:1276) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/5632
[2013-05-02 20:41:32 19545] ERROR (XendDomainInfo:108) Domain construction failed

Traceback (most recent call last):
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 106, in create
    vm.start()
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 474, in start
    XendTask.log_progress(31, 60, self._initDomain)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendTask.py", line 209, in log_progress
    retval = func(*args, **kwds)
  File "/usr/lib/xen-4.1/bin/../lib/python/xen/xend/XendDomainInfo.py", line 2930, in _initDomain
    raise VmError(str(exn))
VmError: (17, 'File exists')



2013/5/2 Jan Beulich <JBeulich@xxxxxxxx>
>>> On 02.05.13 at 14:42, Andreas Falck <falck.andreas.lists@xxxxxxxxx> wrote:
> 2013/5/2 Jan Beulich <JBeulich@xxxxxxxx>
>
>>
>> If you could just try out the tentative solution described in
>> http://lists.xen.org/archives/html/xen-devel/2013-05/msg00145.html
>> that would already help.
>>
>
> I will have a look when I come home from work, it will be a few hours from
> now. Just so that I understand it right, is this simply a matter of editing
> pciif.py and commenting out the line
>
>         if not self.vm.info.is_hvm() and dev.irq:
>
> so that the conditioned code is executed for all guests?

No, not the entire line, just the is_hvm part needs to be dropped.

Jan



_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxx
http://lists.xen.org/xen-users

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.