[Top] [All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] XEN 4.1.2+Centos 6.2+Kernel 3.X

Hey Choon,

On Mon, Feb 6, 2012 at 1:13 AM, Teck Choon Giam <giamteckchoon@xxxxxxxxx> wrote:
On Mon, Feb 6, 2012 at 11:46 AM, David Gonzalez <dgonzalezh@xxxxxxxxx> wrote:
> Hey
>
> On Sat, Feb 4, 2012 at 6:31 PM, Teck Choon Giam <giamteckchoon@xxxxxxxxx>
> wrote:
>>
>> On Sun, Feb 5, 2012 at 6:54 AM, David Gonzalez <dgonzalezh@xxxxxxxxx>
>> wrote:
>> >
>> >
>> > On Sat, Feb 4, 2012 at 5:01 PM, Teck Choon Giam
>> > <giamteckchoon@xxxxxxxxx>
>> > wrote:
>> >>
>> >> On Sun, Feb 5, 2012 at 5:35 AM, David Gonzalez <dgonzalezh@xxxxxxxxx>
>> >> wrote:
>> >> > Yo, Teck, nice name heh,
>> >>
>> >> Grrr... My Surname is Giam and Name is Teck Choon :p

You're from?.
 
>> >>
>> >> >
>> >> > On Sat, Feb 4, 2012 at 2:16 PM, Teck Choon Giam
>> >> > <giamteckchoon@xxxxxxxxx>
>> >> > wrote:
>> >> >>
>> >> >> On Sat, Feb 4, 2012 at 1:25 PM, David Gonzalez
>> >> >> <dgonzalezh@xxxxxxxxx>
>> >> >> wrote:
>> >> >> > Hey hope this opne is a "make senser".
>> >> >> >
>> >> >> > Has anyone tried the "Subject line" combo?, I've compiled a dozen
>> >> >> > src.rpm
>> >> >> > kern el 3.0 and 3.1 packages with no luck to try native upstream
>> >> >> > Dom0
>> >> >> > kernel
>> >> >>
>> >> >> > support with no success, just a kernel oops and constant reboots.
>> >> >>
>> >> >> I have compiled 3.0, 3.1 and 3.2 kernels for dom0 and domU for my
>> >> >> own patched kernels (add iscsitarget as module into it as example).
>> >> >> Tested with xen-4.1.3-rc1-pre.
>> >> >>
>> >> > Ok, I'm guessing that mus me one of my many mistakes when doing this,
>> >> > I
>> >> > haven't added the rite modules.
>> >> >
>> >> >>
>> >> >> >
>> >> >> > I followed Fedora's wiki on building a custom kernel, even used
>> >> >> > F16's >
>> >> >> > .config which also was a no-no. I'd like to try F16 which comes
>> >> >> > with
>> >> >> > 3.0 >
>> >> >> > out-of-the-box, but I've already set up my CentOS 6.2 pretty
>> >> >> > nicely
>> >> >> > to
>> >> >> > just "mkfs.ext3" on it, so if anyone has some _updated_ info (3rd
>> >> >> > quarter
>> >> >> > 2011 or 2012) that I can refer to, please advise.
>> >> >>
>> >> >> Although I don't use CentOS 6.  I use Scientific Linux 6 instead.
>> >> >> Don't use Fedora kernel .config as there are many debug options
>> >> >> enabled if I remember correctly.  Even I use RHEL6 .config for
>> >> >> 2.6.32.x pvops kernel for Jeremy's xen git tree will encounter
>> >> >> problems.  In short, you can use one of those .config then use make
>> >> >> menuconfig to disable power, cgroup, debug etc. options and start
>> >> >> from there as this is how I did.
>> >> >>
>> >> > Hmm, I tried that with rpmbuild -bb kernel.spec and as described on
>> >> > F16
>> >> > wiki, and disabled many many options and the kernel compiled aok and
>> >> > the
>> >> > installed fine but never booted, it kept rebooting.
>> >>
>> >> Just a question... is your xen installed from source or from rpm
>> >> package?
>> >
>> >
>> > It's from myoung Fedora repos it's rpm package, altho I built 4.1.2
>> > myself
>> > but it's not installed from those but froma repo.
>> >>
>> >>
>> >> >
>> >> > I'll try your suggestions and hope that it helps.
>> >>
>> >> If that doesn't, you can use mine instead of burning your time to make
>> >> it work ;)  Anyway, I think it is a good experience to make it work
>> >> from self compile and there are many things to learn from this
>> >> experience.
>> >
>> >
>> > Huh, self-compiled, I've done that a hundred times, but it's always a
>> > no-no,
>> > i'v compiled 2.6.32 to 2.6.40 also 3.0.x to 3.1.x  and no luck either,
>> > I've
>> > got a devel machine runiing also CentOS 6.0 with 4 cores and 2048MB uin
>> > RAM
>> > so itr takes not tyoo long but it's frustrating to reboot and get
>> > nothing.
>> >
>> > I'd like to try yours, do you happen to have a repo or some place to get
>> > your rpms?.
>>
>> The guide is at http://choon.net/forum/read.php?16,672307
>
>
> Well, followed it and  there seemed to be a problem when I downloaded and
> installed the kernel, I installed it with rpm -ivh choon...kernel...rpm and
> the system never came back up online.

Have you try the guide posted and boot into xen-kernel-2.6.32.56-0
first?  If that is successfully, then you can follow the guide to
create the v3.0 or v3.1 or v3.2 kernels repo then enable it and using
yum install choon-kernel to install?  Would appreciate feedback about
the failure or success ;)

Yup, in fact that was what I did to install the kernel, but it kept downloading 2.6.32, so I went ahead and d/loaded 3.1 and 3.2 and installed them via rpm -uvh.
I'm guessing these should be changed or modified to use 3.x series kernels, am I wrong.

# choonrpmsrepoctl create choonrpms-kernels
# choonrpmsrepoctl enable choonrpms-kernels

I also found something about that nice grub parameter I didn't know and it's the "fallback=#" parameter which on the locked server I didn't use, but now i'lkl reboot that machine and check the output
 

>
> I-ll check and report as soon as I get to the DC tomorrow, I'll also check
> the howto again.

Thanks for it in advance.  Please let me know your network ethernet
information (lspci -vvv output and lsmod output) as I am afraid it may
be an issue.  Sometimes, if a board has two same onboard ethernet and
when you boot stock kernel you get the order of eth0 as HW ... 01 and
eth1 as HW ... 02 then when you boot into custom kernel you get the
order being switched.  I encountered it before and checked the udev
rules file to make sure (/etc/udev/rules.d/70-persistent-net.rules) is
correct.

Network doesn't seem to be an issue, I have that server with two onborad NICs which are the same but they're connected to different switches and on two different class C networks, I set up using C6.2 nifcfg-ethX scripts and set them up as bridged xenbr0 and xenbr1. They both work on that server with no issue at all.

the HP ML115 has only one on board NIC which is also a bridge.

Hrere's the outoput you requested but from the WORKING server, as I get the HP ML115 rebooted I-ll get back to you to show you its outputs.

# lspci -vv
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4)
        Subsystem: ASUSTeK Computer Inc. Device 8162
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [44] HyperTransport: Slave or Primary Interface
                Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
                Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
                Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
                Revision ID: 1.03
                Link Frequency 0: 1.0GHz
                Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
                Link Frequency 1: 200MHz
                Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
                Prefetchable memory behind bridge Upper: 00-00
                Bus Number: 00
        Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-
                Mapping Address Base: 00000000fee00000

00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev f1)
        Subsystem: ASUSTeK Computer Inc. Device 8162
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0

00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
        Subsystem: ASUSTeK Computer Inc. Device 8162
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 10
        Region 0: I/O ports at ec00 [size=32]
        Region 4: I/O ports at 4c00 [size=64]
        Region 5: I/O ports at 4e00 [size=64]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: nForce2_smbus
        Kernel modules: i2c-nforce2

00:02.0 USB controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI])
        Subsystem: ASUSTeK Computer Inc. Device 8162
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 23
        Region 0: Memory at f5eff000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ohci_hcd
        Kernel modules: ohci-hcd

00:02.1 USB controller: nVidia Corporation CK804 USB Controller (rev a4) (prog-if 20 [EHCI])
        Subsystem: ASUSTeK Computer Inc. Device 8162
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin B routed to IRQ 22
        Region 0: Memory at feb00000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [44] Debug port: BAR=1 offset=0098
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ehci_hcd
        Kernel modules: ehci-hcd

00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f3) (prog-if 8a [Master SecP PriP])
        Subsystem: ASUSTeK Computer Inc. Device 8162
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
        Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
        Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
        Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
        Region 4: I/O ports at ffa0 [size=16]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: AMD_IDE

00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
        Subsystem: ASUSTeK Computer Inc. Device 8162
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 21
        Region 0: I/O ports at e480 [size=8]
        Region 1: I/O ports at e400 [size=4]
        Region 2: I/O ports at e080 [size=8]
        Region 3: I/O ports at e000 [size=4]
        Region 4: I/O ports at dc00 [size=16]
        Region 5: Memory at f5efd000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: sata_nv
        Kernel modules: sata_nv

00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
        Subsystem: ASUSTeK Computer Inc. Device 8162
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 20
        Region 0: I/O ports at d880 [size=8]
        Region 1: I/O ports at d800 [size=4]
        Region 2: I/O ports at d480 [size=8]
        Region 3: I/O ports at d400 [size=4]
        Region 4: I/O ports at d080 [size=16]
        Region 5: Memory at f5efc000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: sata_nv
        Kernel modules: sata_nv

00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev f2) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        I/O behind bridge: 00009000-00009fff
        Memory behind bridge: f5600000-f56fffff
        Prefetchable memory behind bridge: f5f00000-fdefffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-

00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode])
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        Memory behind bridge: f5700000-f57fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+
                Address: 00000000feeff00c  Data: 4198
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #3, Speed 2.5GT/s, Width x2, ASPM L0s, Latency L0 <512ns, L1 <4us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  8, PowerLimit 25.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn+ PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [160] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                AERCap: First Error Pointer: 0c, GenCap+ CGenEn- ChkCap+ ChkEn-
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode])
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        Memory behind bridge: f5800000-f58fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+
                Address: 00000000feeff00c  Data: 41a0
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #2, Speed 2.5GT/s, Width x2, ASPM L0s, Latency L0 <512ns, L1 <4us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  4, PowerLimit 25.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn+ PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [160] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        I/O behind bridge: 0000a000-0000cfff
        Memory behind bridge: f5900000-f5dfffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+
                Address: 00000000feeff00c  Data: 41a8
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #1, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 <512ns, L1 <4us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  2, PowerLimit 25.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [160] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
        Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+
                Address: 00000000feeff00c  Data: 41b0
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 <512ns, L1 <4us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  1, PowerLimit 25.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [160] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Capabilities: [80] HyperTransport: Host or Secondary Interface
                Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
                Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
                Revision ID: 3.00
                Link Frequency: 1.0GHz
                Link Error: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
        Capabilities: [a0] HyperTransport: Host or Secondary Interface
                Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
                Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
                Revision ID: 3.00
                Link Frequency: 1.0GHz
                Link Error: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
        Capabilities: [c0] HyperTransport: Host or Secondary Interface
                Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
                Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
                Revision ID: 3.00
                Link Frequency: 1.0GHz
                Link Error: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-

00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Kernel driver in use: amd64_edac
        Kernel modules: amd64_edac_mod

00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Capabilities: [f0] Secure device <?>
        Kernel modules: k10temp

00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:19.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Capabilities: [80] HyperTransport: Host or Secondary Interface
                Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
                Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
                Revision ID: 3.00
                Link Frequency: 1.0GHz
                Link Error: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
        Capabilities: [a0] HyperTransport: Host or Secondary Interface
                Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
                Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
                Revision ID: 3.00
                Link Frequency: 1.0GHz
                Link Error: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
        Capabilities: [c0] HyperTransport: Host or Secondary Interface
                Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
                Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=N/C DwFcInEn- LWO=N/C DwFcOutEn-
                Revision ID: 3.00
                Link Frequency: 200MHz
                Link Error: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-

00:19.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:19.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Kernel driver in use: amd64_edac
        Kernel modules: amd64_edac_mod

00:19.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Capabilities: [f0] Secure device <?>
        Kernel modules: k10temp

00:19.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

01:04.0 VGA compatible controller: XGI Technology Inc. (eXtreme Graphics Innovation) Z7/Z9 (XG20 core) (prog-if 00 [VGA controller])
        Subsystem: ASUSTeK Computer Inc. Device 82b4
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        BIST result: 00
        Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
        Region 1: Memory at f56c0000 (32-bit, non-prefetchable) [size=256K]
        Region 2: I/O ports at 9c00 [size=128]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 21)
        Subsystem: ASUSTeK Computer Inc. Device 8149
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 283
        Region 0: Memory at f57f0000 (64-bit, non-prefetchable) [size=64K]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
                Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
                Read-only fields:
                        [PN] Part number: BCM95721
                        [EC] Engineering changes: 106679-15
                        [SN] Serial number: 0123456789
                        [MN] Manufacture ID: 31 34 65 34
                        [RV] Reserved: checksum bad, 28 byte(s) reserved
                Read/write fields:
                        [YA] Asset tag: XYZ01234567
                        [RW] Read-write area: 107 byte(s) free
                End
        Capabilities: [58] MSI: Enable+ Count=1/8 Maskable- 64bit+
                Address: 00000000fee0100c  Data: 4131
        Capabilities: [d0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 4096 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [13c] Virtual Channel <?>
        Capabilities: [160] Device Serial Number 00-1e-8c-ff-fe-51-61-c0
        Capabilities: [16c] Power Budgeting <?>
        Kernel driver in use: tg3
        Kernel modules: tg3

03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 21)
        Subsystem: ASUSTeK Computer Inc. Device 8149
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 284
        Region 0: Memory at f58f0000 (64-bit, non-prefetchable) [size=64K]
        Expansion ROM at <ignored> [disabled]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
                Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
                Read-only fields:
                        [PN] Part number: BCM95721
                        [EC] Engineering changes: 106679-15
                        [SN] Serial number: 0123456789
                        [MN] Manufacture ID: 31 34 65 34
                        [RV] Reserved: checksum bad, 28 byte(s) reserved
                Read/write fields:
                        [YA] Asset tag: XYZ01234567
                        [RW] Read-write area: 107 byte(s) free
                End
        Capabilities: [58] MSI: Enable+ Count=1/8 Maskable- 64bit+
                Address: 00000000fee0100c  Data: 4139
        Capabilities: [d0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 4096 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [13c] Virtual Channel <?>
        Capabilities: [160] Device Serial Number 00-1e-8c-ff-fe-51-63-b3
        Capabilities: [16c] Power Budgeting <?>
        Kernel driver in use: tg3
        Kernel modules: tg3

04:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)
        Subsystem: ASUSTeK Computer Inc. Device 82c3
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: I/O ports at c000 [size=256]
        Region 1: Memory at f5dfc000 (64-bit, non-prefetchable) [size=16K]
        Region 3: Memory at f5de0000 (64-bit, non-prefetchable) [size=64K]
        Expansion ROM at f5a00000 [disabled] [size=2M]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [68] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency L0 <64ns, L1 <1us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
        Capabilities: [98] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 0000000000000000  Data: 0000
        Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
                Vector table: BAR=1 offset=00002000
                PBA: BAR=1 offset=00003000
        Capabilities: [100] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Kernel driver in use: mptsas
        Kernel modules: mptsas

# lsmod
Module                  Size  Used by
xen_gntalloc            4065  0
sunrpc                204202  1
bridge                 69381  0
stp                     1939  1 bridge
ipv6                  242255  33 bridge
microcode             108233  0
pcspkr                  1814  0
serio_raw               4155  0
k10temp                 3167  0
hwmon                   1703  1 k10temp
amd64_edac_mod         18819  0
edac_core              39964  4 amd64_edac_mod
tg3                   122274  0
libphy                 20670  1 tg3
sg                     25143  0
i2c_nforce2             5205  0
i2c_core               22702  1 i2c_nforce2
ext4                  243772  6
jbd2                   53102  1 ext4
crc16                   1595  1 ext4
sd_mod                 25759  5
mptsas                 45838  0
mptscsih               29531  1 mptsas
mptbase                84265  2 mptsas,mptscsih
scsi_transport_sas     28533  1 mptsas
sata_nv                19346  3
libata                164765  1 sata_nv
scsi_mod              156890  6 sg,sd_mod,mptsas,mptscsih,scsi_transport_sas,libata
ehci_hcd               33653  0
ohci_hcd               18209  0
button                  5111  0
dm_mirror              12064  0
dm_region_hash          9658  1 dm_mirror
dm_log                  8240  2 dm_mirror,dm_region_hash
dm_mod                 65814  20 dm_mirror,dm_log

 

>
> Many many thanks for taking the toime to put together that nice and useful
> info.

Those repos are there for years actually just that SL6/CentOS6 are
considered quite new in those repos.  I used the same repos when using
CentOS 5 as dom0 last time but cease it due to the time involved to
support those in CentOS 5.  I rather focus on SL6/CentOS6 :)  Just
beware that all my dom0 servers are SL6 based.

Feedbacks are greatly appreciated and if you need assistance off this
list are welcome (just compose another new mail direct to me so that I
know it is not from this xen-users list).

Thank you for taking the toine to read and answer.
 
Thanks.

Kindest regards,
Giam Teck Choon

>>
>>
>> Thanks.
>>
>> Kindest regards,
>> Giam Teck Choon
>>
>>
>> >>
>> >>
>> >> >
>> >> > Thank you very much.
>> >>
>> >> Thanks.
>> >
>> >
>> > Again.
>> > --
>> > David Gonzalez H.
>> > Bogota: +(57-1)289-1168
>> > Medellin: +(57-1)247-0985
>> > Cel: +(57)315-838-8326
>> > DGHVoIP - OPEN SOURCE TELEPHONY SOLUTIONS
>> > http://www.dghvoip.com/
>> > Proud Linux User #294661
>
>
>
>
> --
> David Gonzalez H.
> Bogota: +(57-1)289-1168
> Medellin: +(57-1)247-0985
> Cel: +(57)315-838-8326
> DGHVoIP - OPEN SOURCE TELEPHONY SOLUTIONS
> http://www.dghvoip.com/
> Proud Linux User #294661



--
David Gonzalez H.
Bogota: +(57-1)289-1168
Medellin: +(57-1)247-0985
Cel: +(57)315-838-8326
DGHVoIP - OPEN SOURCE TELEPHONY SOLUTIONS
http://www.dghvoip.com/
Proud Linux User #294661
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

 

©2013 Xen Project, A Linux Foundation Collaborative Project. All Rights Reserved.
Linux Foundation is a registered trademark of The Linux Foundation.
Xen Project is a trademark of The Linux Foundation.

Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.