Re: [Xen-users] pcifront problem in Ubuntu 10.04 domU

[Francisco Barrera <francisco.barrera@xxxxxxxxx>]

Hello Mark,

I don't really understand your first question.
If it is related with if I use pygrub or dom0 kernel files in the config file from domU, the response is not, I use pygrub.

For the second question, I use this kernel because in dom0 I use CentOS,not Ubuntu. 

Hope this clarify your questions.


Besides I told in the first mail, I review dmesg in domU, and the result it looks ok:
[    2.036868] pcifront pci-0: Creating PCI Frontend Bus 0000:00
[    2.037494] pci 0000:00:00.0: [14e4:164c] type 0 class 0x000200
[    2.038642] pci 0000:00:00.0: reg 10: [mem 0xd2000000-0xd3ffffff 64bit]
[    2.042682] pci 0000:00:00.0: PME# supported from D3hot D3cold
[    2.042731] pci 0000:00:00.0: PME# disabled
[    2.045954] Initialising Xen virtual ethernet driver.
[    2.142451] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[    2.151373] pcifront pci-0: claiming resource 0000:00:00.0/0
[    2.210242] lp: driver loaded but no devices found
[    2.261647] bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.0.18 (Oct 7, 2010)
[    2.261772] bnx2 0000:00:00.0: enabling device (0000 -> 0002)
[    2.262184] bnx2 0000:00:00.0: Xen PCI enabling IRQ: 19
[    2.340687] bnx2 0000:00:00.0: eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d2000000, IRQ 19, node addr 00:10:18:39:9a:f0



Thanks very much.


El mié, 11-05-2011 a las 08:47 -0700, Mark Pryor escribió:
> --- On Wed, 5/11/11, Francisco Barrera <francisco.barrera@xxxxxxxxx> wrote:
>
> From: Francisco Barrera <francisco.barrera@xxxxxxxxx>
> Subject: [Xen-users] pcifront problem in Ubuntu 10.04 domU
> To: xen-users@xxxxxxxxxxxxxxxxxxx
> Date: Wednesday, May 11, 2011, 5:10 AM
>
>   
>   
> Hi all,
>
>
>
> I have a problem when from domU I need to configure a network interface.
>
>
> Kernel driver in use: pciback
>
> Kernel modules: bnx2
>
> domU: paravirtual Ubuntu 10.04  with 2.6.37-020637-generic kernel
>
> Apparently works fine, because I execute from dom0 when domU is created "xm pci-list Ubuntu" and the result is:
>
> domain   bus   slot   func
>
> 0x0000  0x09   0x00    0x0
>
>
>
> and from domU I execute lspci, it returns:
>
> 00:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12)
>
> -------------------
>
> You are using a PPA kernel from dom0. Did you copy over the modules to domU?
>
> What does the PPA kernel provide you that the Lucid kernel can't?



_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users