RE: [Xen-users] Re: XCP 0.5 - dom0 vcpus/RAM settings not working

["Joe Linoff" <jlinoff@xxxxxxxxxx>]

Hi Dante:

Thank you for your suggestions. 

Unfortunately "xm" is not available on XCP servers. I tried "xe list" because 
"xe" is installed but got the message "Unknown command: list".

Similarly, xend doesn't seem to be installed: /var/log/xen is empty.

My guess is that your suggestions are for "Xen Hypervisor" not XCP. Do you know 
what the analogous commands are for XCP?

Regards,

Joe

-----Original Message-----
From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx 
[mailto:xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Dante Cinco
Sent: Wednesday, December 01, 2010 12:51 PM
To: Joe Linoff
Cc: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: [Xen-users] Re: XCP 0.5 - dom0 vcpus/RAM settings not working

Try "xm list" and verify the xen_commandline.

You can also check /var/log/xen/xend.log and search for "vcpus" and
"memsize" (the latest logs are at the bottom so search from the
bottom-up).

Dante

On Wed, Dec 1, 2010 at 10:43 AM, Joe Linoff <jlinoff@xxxxxxxxxx> wrote:
> Hi Dante:
>
> Thank you for your suggestions. I tried them but I am still seeing 477MB
> of RAM and 1 cpu after re-installation. Here are the settings:
>
>  append xenserver/xen.gz dom0_mem=2048M dom0_max_vcpus=2 ...
>
> Can you suggest a way to debug this?
>
> Cheers,
>
> Joe
>
>
> -----Original Message-----
> From: Dante Cinco [mailto:dantecinco@xxxxxxxxx]
> Sent: Wednesday, December 01, 2010 10:28 AM
> To: xen-users@xxxxxxxxxxxxxxxxxxx; Joe Linoff
> Subject: RE: XCP 0.5 - dom0 vcpus/RAM settings not working
>
> You need to change dom0_vcpus_max to dom0_max_vcpus.
>
> If you want 2GB RAM, use dom0_mem=2048M.
>
> Dante
>
>
>
> From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
> [mailto:xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Joe Linoff
> Sent: Wednesday, December 01, 2010 10:01 AM
> To: xen-users@xxxxxxxxxxxxxxxxxxx
> Cc: Joe Linoff
> Subject: [Xen-users] XCP 0.5 - dom0 vcpus/RAM settings not working
>
> Hi Folks:
>
> What am I doing wrong? How do I configure my dom0 to have 2 vcpus and
> 2GB RAM?
>
> I am trying to configure my dom0 to have 2 vcpus and 2GB of RAM. Here
> are my config settings (pxlinux.cfg/default):
>
> kernel mboot.c32
> append xenserver/xen.gz dom0_mem=2097512 dom0_vcpus_max=2
> dom0_vcpus_pin com1=115200,8n1 console=com1,tty --- xenserver/vmlinux
> ...
>
> Everything installs correctly but when I log into dom0 and look at
> /proc/cpuinfo there is only processor. Similarly, when I look
> /proc/meminfo I only see 477MB.
>
> Cheers,
>
> Joe
>

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users