[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Xen-users] can not unbind pci device, xen kernel, openSUSE
- To: Richie <listmail@xxxxxxxxxxxx>
- From: István HERCZEG <advoper@xxxxxxxxx>
- Date: Sat, 30 Oct 2010 18:05:27 +0200
- Cc: xen-users@xxxxxxxxxxxxxxxxxxx
- Delivery-date: Sat, 30 Oct 2010 09:07:38 -0700
- Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=mime-version:in-reply-to:references:date:message-id:subject:from:to :cc:content-type; b=kmXQUmDNpREaLYOED3xRaM6lmVL/hWBD5cCMGBpnsIrYhvT0sBAkXZbIixzruX/HkI NIL9XYuNGwSfNgBauYstnYNH9d6ZVFomVCr9fB1xcpnRHRZTktm7+/dVH2HQJjX/Yyyn 61ZA8uu1bwpFFvqexBXkFm0Y7ToW1aiWAvNas=
- List-id: Xen user discussion <xen-users.lists.xensource.com>
I found the reason way I can't find the ../pciback directory. The pciback module makes available ../pciback.
After I did
modprobe pciback
then I can access /sys/bus/pci/drivers/pciback and wirte the new_slot and bind (instead of bindcat)
doing:
dmesg | grep -i seiz
[ 1613.652339] pciback 0000:00:1a.0: seizing device
[ 1700.984342] pciback 0000:00:1d.0: seizing device
seems ok.
but
xm create windowsxp-2 pci=00:1a.0 pci=00:1d.0
Using config file "./windowsxp-2".
Error: failed to assign device: maybe the platform doesn't support VT-d, or VT-d isn't enabled properly?
:( failure again...
2010. október 30. 17:56 Richie írta, <listmail@xxxxxxxxxxxx>:
On 10/30/2010 11:39 AM, István HERCZEG wrote:
Hi,
thank you for quick answer. You was right I missed the format. But I still have a problem. Continue the PCI unbind procedure the wiki says[1]:
echo -n "0000:00:1a.0" /sys/bus/pci/drivers/pciback/new_slot
and ..
echo -n "0000:00:1a.0" /sys/bus/pci/drivers/pciback/bind_cat
In my openSUSE 11.2 there are no /sys/bus/pci/drivers/pciback directory. OK. I have /sys/bus/pci/drivers/pci-stub maybe this would be nice[2]:
continuing the procedure:
echo -n "0000:00:1a.0" /sys/bus/pci/drivers/pci-stub/new_slot
-bash: new_slot: No such file or directory
echo -n "0000:00:1a.0" /sys/bus/pci/drivers/pci-stub/bindcat
-bash: bindcat: No such file or directory
I get these messages ...
Regards,
Istvan
first find your device in lspci -n output
Say I had a device as follows:
00:01.0 0604: 8086:29a1 (rev 02)
I'd try:
echo "8086 29a1" > /sys/bus/pci/drivers/pci-stub/new_id
echo "0000:00:01.0" > /sys/bus/pci/devices/0000:00:01.0/driver/unbind
echo "0000:00:01.0" > /sys/bus/pci/drivers/pci-stub/bind
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
