[Xen-users] Re: dom0 Kernel panic after enable CONFIG_X86_BIGSMP and change CONFIG_NR_CPUS=16 on 2.6.32 or 2.6.33

[lei yang <yanglei.fage@xxxxxxxxx>]

 

Anyone met this issue?

On Mon, May 31, 2010 at 10:46 AM, lei yang <yanglei.fage@xxxxxxxxx> wrote:

Hi experts

I have a nehalem board with 8 phy cors and support ht

This is the boot log

[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] xen_release_chunk: looking at area pfn 90000-a0000: 65536 pages freed
[    0.000000] xen_release_chunk: looking at area pfn b0000-fc000: 311296 pages freed
[    0.000000] xen_release_chunk: looking at area pfn fd000-fec00: 7168 pages freed
[    0.000000] xen_release_chunk: looking at area pfn fec01-fec90: 143 pages freed
[    0.000000] xen_release_chunk: looking at area pfn fec91-fed1c: 139 pages freed
[    0.000000] xen_release_chunk: looking at area pfn fed20-fee00: 224 pages freed
[    0.000000] xen_release_chunk: looking at area pfn fee01-ff800: 2559 pages freed
[    0.000000] released 387065 pages of unused memory
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  Xen: 0000000000000000 - 000000000009c000 (usable)
[    0.000000]  Xen: 000000000009c000 - 0000000000100000 (reserved)
[    0.000000]  Xen: 0000000000100000 - 000000008c42d000 (usable)
[    0.000000]  Xen: 000000008c42d000 - 000000008d82d000 (ACPI NVS)
[    0.000000]  Xen: 000000008d82d000 - 000000008f602000 (ACPI data)
[    0.000000]  Xen: 000000008f602000 - 000000008f64f000 (reserved)
[    0.000000]  Xen: 000000008f64f000 - 000000008f66d000 (ACPI data)
[    0.000000]  Xen: 000000008f66d000 - 000000008f7cf000 (ACPI NVS)
[    0.000000]  Xen: 000000008f7cf000 - 000000008f800000 (ACPI data)
[    0.000000]  Xen: 000000008f800000 - 0000000090000000 (reserved)
[    0.000000]  Xen: 00000000a0000000 - 00000000b0000000 (reserved)
[    0.000000]  Xen: 00000000fc000000 - 00000000fd000000 (reserved)
[    0.000000]  Xen: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  Xen: 00000000fec90000 - 00000000fec91000 (reserved)
[    0.000000]  Xen: 00000000fed1c000 - 00000000fed20000 (reserved)
[    0.000000]  Xen: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  Xen: 00000000ff800000 - 0000000100000000 (reserved)
[    0.000000]  Xen: 0000000100000000 - 000000037acf2000 (usable)
[    0.000000]  Xen: 0000000400000000 - 0000000670000000 (unusable)
[    0.000000] DMI 2.5 present.
[    0.000000] last_pfn = 0x37acf2 max_arch_pfn = 0x1000000
[    0.000000] x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000002000 (usable)
[    0.000000]  modified: 0000000000002000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 000000000009c000 (usable)
[    0.000000]  modified: 000000000009c000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000008c42d000 (usable)
[    0.000000]  modified: 000000008c42d000 - 000000008d82d000 (ACPI NVS)
[    0.000000]  modified: 000000008d82d000 - 000000008f602000 (ACPI data)
[    0.000000]  modified: 000000008f602000 - 000000008f64f000 (reserved)
[    0.000000]  modified: 000000008f64f000 - 000000008f66d000 (ACPI data)
[    0.000000]  modified: 000000008f66d000 - 000000008f7cf000 (ACPI NVS)
[    0.000000]  modified: 000000008f7cf000 - 000000008f800000 (ACPI data)
[    0.000000]  modified: 000000008f800000 - 0000000090000000 (reserved)
[    0.000000]  modified: 00000000a0000000 - 00000000b0000000 (reserved)
[    0.000000]  modified: 00000000fc000000 - 00000000fd000000 (reserved)
[    0.000000]  modified: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  modified: 00000000fec90000 - 00000000fec91000 (reserved)
[    0.000000]  modified: 00000000fed1c000 - 00000000fed20000 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000ff800000 - 0000000100000000 (reserved)
[    0.000000]  modified: 0000000100000000 - 000000037acf2000 (usable)
[    0.000000]  modified: 0000000400000000 - 0000000670000000 (unusable)
[    0.000000] init_memory_mapping: 0000000000000000-000000002d1fe000
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] ACPI: RSDP 000f03f0 00024 (v02 INTEL )
[    0.000000] ACPI: XSDT 8f7fe120 0009C (v01 INTEL  S5520HC  00000000      01000013)
[    0.000000] ACPI: FACP 8f7fc000 000F4 (v04 INTEL  S5520HC  00000000 MSFT 0100000D)
[    0.000000] ACPI: DSDT 8f7f5000 06404 (v02 INTEL  S5520HC  00000003 MSFT 0100000D)
[    0.000000] ACPI: FACS 8f735000 00040
[    0.000000] ACPI: APIC 8f7f4000 00138 (v02 INTEL  S5520HC  00000000 MSFT 0100000D)
[    0.000000] ACPI: MCFG 8f7f3000 0003C (v01 INTEL  S5520HC  00000001 MSFT 0100000D)
[    0.000000] ACPI: HPET 8f7f2000 00038 (v01 INTEL  S5520HC  00000001 MSFT 0100000D)
[    0.000000] ACPI: SLIT 8f7f1000 00030 (v01 INTEL  S5520HC  00000001 MSFT 0100000D)
[    0.000000] ACPI: SRAT 8f7f0000 003B0 (v02 INTEL  S5520HC  00000001 MSFT 0100000D)
[    0.000000] ACPI: SPCR 8f7ef000 00050 (v01 INTEL  S5520HC  00000000 MSFT 0100000D)
[    0.000000] ACPI: WDDT 8f7ee000 00040 (v01 INTEL  S5520HC  00000000 MSFT 0100000D)
[    0.000000] ACPI: SSDT 8f7dc000 11FE4 (v02  INTEL SSDT  PM 00004000 INTL 20061109)
[    0.000000] ACPI: SSDT 8f7db000 001D8 (v02  INTEL IPMI     00004000 INTL 20061109)
[    0.000000] ACPI: HEST 8f7d9000 000A8 (v01 INTEL  S5520HC  00000001 INTL 00000001)
[    0.000000] ACPI: BERT 8f7d8000 00030 (v01 INTEL  S5520HC  00000001 INTL 00000001)
[    0.000000] ACPI: ERST 8f7d7000 00230 (v01 INTEL  S5520HC  00000001 INTL 00000001)
[    0.000000] ACPI: EINJ 8f7d6000 00130 (v01 INTEL  S5520HC  00000001 INTL 00000001)
[    0.000000] ACPI:      8f7d5000 001D0 (v01 INTEL  S5520HC  00000001 MSFT 0100000D)
[    0.000000] Node: 0, start_pfn: 0, end_pfn: 37acf2
[    0.000000] Reserving total of 7000 pages for numa KVA remap
[    0.000000] kva_start_pfn ~ 26000 max_low_pfn ~ 2d1fe
[    0.000000] max_pfn = 37acf2
[    0.000000] 13530MB HIGHMEM available.
[    0.000000] 721MB LOWMEM available.
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Not tainted 2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Not tainted 2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da22 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da23 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da24 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da25 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da26 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da27 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da28 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da29 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da2a ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da2b ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da2c ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da2d ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da2e ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da2f ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da30 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da31 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da32 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da33 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da34 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da35 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da36 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da37 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da38 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da39 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da3a ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da3b ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da3c ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da3d ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da3e ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da3f ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da40 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/x86/xen/multicalls.c:182 xen_mc_flush+0x20d/0x215()
[    0.000000] Hardware name: S5520HC
[    0.000000] Modules linked in:
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c103d895>] warn_slowpath_common+0x60/0x90
[    0.000000]  [<c103d8d2>] warn_slowpath_null+0xd/0x10
[    0.000000]  [<c100481c>] xen_mc_flush+0x20d/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] set_pmd_pfn+0xe3/0x100
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c17942c6>] initmem_init+0x4eb/0x630
[    0.000000]  [<c17a2a63>] ? acpi_table_parse_madt+0x16/0x18
[    0.000000]  [<c178aaa9>] ? acpi_parse_lapic_addr_ovr+0x0/0x32
[    0.000000]  [<c1785c6c>] setup_arch+0x82b/0xa42
[    0.000000]  [<c103de38>] ? release_console_sem+0x19e/0x1cb
[    0.000000]  [<c103e32b>] ? vprintk+0x2fd/0x320
[    0.000000]  [<c1780020>] ? i386_start_kernel+0xf/0x96
[    0.000000]  [<c1006c46>] ? __raw_callee_save_xen_restore_fl+0x6/0x8
[    0.000000]  [<c17805d9>] start_kernel+0x86/0x360
[    0.000000]  [<c17800a2>] i386_start_kernel+0x91/0x96
[    0.000000]  [<c1783642>] xen_start_kernel+0x625/0x62d
[    0.000000] ---[ end trace 4eaa2a86a8e2da41 ]---
[    0.000000] 1 multicall(s) failed: cpu 0
[    0.000000] Pid: 0, comm: swapper Tainted: G        W  2.6.32.13 #2
[    0.000000] Call Trace:
[    0.000000]  [<c14b7acc>] ? printk+0xf/0x11
[    0.000000]  [<c1004744>] xen_mc_flush+0x135/0x215
[    0.000000]  [<c100529d>] xen_mc_issue+0x14/0x42
[    0.000000]  [<c100651a>] xen_set_pmd_hyper+0xa2/0xaa
[    0.000000]  [<c102a763>] se

-- 
"We learn from failure, not from success!"
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users