|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Xen-users] XEN 4.0 boot error
On Thu, Apr 08, 2010 at 09:46:49PM +0200, For@ll wrote: > > See here for help: > [2][3]http://wiki.xensource.com/xenwiki/XenParavirtOps > > > > I have the same problem to boot xen 4.0 on debian lenny 5.0, under > I > > paste a some error: > > > > 41.017078] Magic number: 6:876:244 > > [ 41.061177] md: Waiting for all devices to be available before > > autodetect > > [ 41.142579] md: If you don't use raid, use raid=noautodetect > > [ 41.211225] md: Autodetecting RAID arrays. > > [ 41.260417] md: Scanned 0 and added 0 devices. > > [ 41.313729] md: autorun ... > > [ 41.347281] md: ... autorun DONE. > > [ 41.387150] Root-NFS: No NFS server available, giving up. > > [ 41.451921] VFS: Unable to mount root fs via NFS, trying floppy. > > [ 41.524664] VFS: Cannot open root device "sda1" or > unknown-block(2,0) > > So the disk was not detected, or did you pass wrong root= parameter? > > Please post the _full_ log. > > -- Pasi > > > Hi, > > This is a longer version dmesg from console redirection ( ipmitool connect > to iRMC) > I don't see any disks detected in the log.. Can you please post a boot log on baremetal (non-xen), or tell which disk controller has your root disk? what driver it uses on baremetal linux? -- Pasi > [ 25.101873] xen_set_ioapic_routing: irq 16 gsi 16 vector 16 ioapic 0 > pin 16 triggering 1 polarity 1 > [ 25.210426] pci 0000:00:1c.7: PCI INT A -> GSI 16 (level, low) -> IRQ > 16 > [ 25.290926] NET: Registered protocol family 2 > [ 25.343369] IP route cache hash table entries: 32768 (order: 5, 131072 > bytes) > [ 25.429385] TCP established hash table entries: 131072 (order: 8, > 1048576 bytes) > [ 25.518783] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) > [ 25.598413] TCP: Hash tables configured (established 131072 bind 65536) > [ 25.677741] TCP reno registered > [ 25.715586] NET: Registered protocol family 1 > [ 25.767966] kvm: no hardware support > [ 25.810908] has_svm: not amd > [ 25.845501] kvm: no hardware support > [ 25.888606] Simple Boot Flag at 0x50 set to 0x1 > [ 25.946611] Microcode Update Driver: v2.00 > <[4]tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba > [ 26.040604] Scanning for low memory corruption every 60 seconds > [ 26.112527] audit: initializing netlink socket (disabled) > [ 26.179722] type=2000 audit(1270763053.504:1): initialized > [ 11.184373] highmem bounce pool size: 64 pages > [ 11.237701] HugeTLB registered 2 MB page size, pre-allocated 0 pages > [ 11.319190] VFS: Disk quotas dquot_6.5.2 > [ 11.366415] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 11.445284] DLM (built Apr 8 2010 14:55:36) installed > [ 11.508815] OCFS2 1.5.0 > [ 11.538530] ocfs2: Registered cluster interface o2cb > [ 11.598381] ocfs2: Registered cluster interface user > [ 11.657945] OCFS2 Node Manager 1.5.0 > [ 11.701011] OCFS2 DLM 1.5.0 > [ 11.734622] OCFS2 DLMFS 1.5.0 > [ 11.770430] OCFS2 User DLM kernel interface loaded > [ 11.828680] Slow work thread pool: Starting up > [ 11.882081] Slow work thread pool: Ready > [ 11.929163] GFS2 (built Apr 8 2010 14:56:07) installed > [ 11.991853] msgmni has been set to 1248 > [ 12.039039] alg: No test for stdrng (krng) > [ 12.088412] Block layer SCSI generic (bsg) driver version 0.4 loaded > (major 252) > [ 12.177207] io scheduler noop registered > [ 12.224285] io scheduler anticipatory registered > [ 12.279686] io scheduler deadline registered > [ 12.330936] io scheduler cfq registered (default) > [ 12.390106] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 12.457519] ACPI: AC Adapter [PSD] (on-line) > [ 12.509066] input: Power Button as > /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 > [ 12.597857] ACPI: Power Button [PWRF] > [ 12.641975] input: Power Button as > /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 > [ 12.740153] ACPI: Power Button [PWRB] > [ 12.784590] ACPI: CPU-1 (power states: C1[C1] C2[C3]) > [ 12.845935] ACPI: CPU-1 (power states: C1[C1] C2[C3]) > [ 12.907366] ACPI: CPU-1 (power states: C1[C1] C2[C3]) > [ 12.968754] ACPI: CPU-1 (power states: C1[C1] C2[C3]) > [ 13.034662] Event-channel device installed. > [ 13.088923] blktap_device_init: blktap device major 253 > [ 13.151673] blktap_ring_init: blktap ring major: 251 > [ 13.212676] registering netback > [ 13.260648] hpet_acpi_add: no address or irqs in _CRS > [ 13.321642] Non-volatile memory driver v1.3 > [ 13.372539] Linux agpgart interface v0.103 > [ 13.422152] [drm] Initialized drm 1.1.0 20060810 > [ 13.477799] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > ÿ[ 13.797361] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 13.872710] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 13.946381] brd: module loaded > [ 13.985783] loop: module loaded > [ 14.024058] input: Macintosh mouse button emulation as > /devices/virtual/input/input2 > [ 14.118477] xen_set_ioapic_routing: irq 22 gsi 22 vector 22 ioapic 0 > pin 22 triggering 1 polarity 1 > [ 14.227076] ata_piix 0000:00:1f.2: PCI INT A -> GSI 22 (level, low) -> > IRQ 22 > [ 14.312643] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] > [ 14.375473] scsi0 : ata_piix > [ 14.410844] scsi1 : ata_piix > [ 14.445932] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x1870 > irq 14 > [ 14.529487] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1878 > irq 15 > [ 14.613055] xen_set_ioapic_routing: irq 23 gsi 23 vector 23 ioapic 0 > pin 23 triggering 1 polarity 1 > [ 14.721616] ata_piix 0000:00:1f.5: PCI INT B -> GSI 23 (level, low) -> > IRQ 23 > [ 14.807293] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] > [ 14.870023] scsi2 : ata_piix > [ 14.905173] scsi3 : ata_piix > [ 14.940127] ata3: SATA max UDMA/133 cmd 0x18c8 ctl 0x18bc bmdma 0x1890 > irq 23 > [ 15.025708] ata4: SATA max UDMA/133 cmd 0x18c0 ctl 0x18b8 bmdma 0x1898 > irq 23 > [ 15.112211] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI > [ 15.189453] Copyright (c) 1999-2006 Intel Corporation. > [ 30.313754] ata2.00: SATA link down (SStatus 0 SControl 300) > [ 30.313848] ata2.01: SATA link down (SStatus 0 SControl 300) > [ 30.326241] ata1.00: SATA link down (SStatus 0 SControl 300) > [ 30.326268] ata1.01: SATA link down (SStatus 0 SControl 300) > [ 30.500741] ata4: SATA link down (SStatus 0 SControl 300) > [ 15.587630] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 > [ 16.373656] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > [ 16.392986] ata3.00: ATAPI: HL-DT-ST DVDRAM GT20N, CW03, max UDMA/133 > [ 16.414991] ata3.00: configured for UDMA/133 > [ 30.751248] scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GT20N > CW03 PQ: 0 ANSI: 5 > [ 30.763236] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 > cdda tray > [ 30.763240] Uniform CD-ROM driver Revision: 3.20 > [ 30.764188] sr 2:0:0:0: Attached scsi generic sg0 type 5 > [ 16.167491] e1000e: Copyright (c) 1999-2008 Intel Corporation. > [ 16.237533] xen_set_ioapic_routing: irq 17 gsi 17 vector 17 ioapic 0 > pin 17 triggering 1 polarity 1 > [ 16.346385] e1000e 0000:00:19.0: PCI INT A -> GSI 17 (level, low) -> > IRQ 17 > [ 16.429871] e1000e 0000:00:19.0: pci_enable_pcie_error_reporting failed > 0xfffffffb > [ 16.631590] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) > 00:40:d0:c0:94:ab > [ 16.720405] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection > [ 16.798930] 0000:00:19.0: eth0: MAC: 9, PHY: 9, PBA No: 313130-032 > [ 16.873209] xen_set_ioapic_routing: irq 18 gsi 18 vector 18 ioapic 0 > pin 18 triggering 1 polarity 1 > [ 16.981766] e1000e 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> > IRQ 18 > [ 17.151067] 0000:06:00.0: eth1: (PCI Express:2.5GB/s:Width x1) > 00:40:d0:c0:94:aa > [ 17.239785] 0000:06:00.0: eth1: Intel(R) PRO/1000 Network Connection > [ 17.316095] 0000:06:00.0: eth1: MAC: 3, PHY: 8, PBA No: 313132-030 > [ 17.390967] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI > [ 17.464089] e100: Copyright(c) 1999-2006 Intel Corporation > [ 17.530921] sky2 driver version 1.23 > [ 17.575855] console [netcon0] enabled > [ 17.619813] netconsole: network logging started > [ 17.674531] Fusion MPT base driver 3.04.10 > [ 17.723728] Copyright (c) 1999-2008 LSI Corporation > [ 17.782276] Fusion MPT FC Host driver 3.04.10 > [ 17.834877] Fusion MPT misc device (ioctl) driver 3.04.10 > [ 17.900030] mptctl: Registered with Fusion MPT base driver > [ 17.965842] mptctl: /dev/mptctl @ (major,minor=10,220) > [ 18.028613] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > [ 18.106968] xen_set_ioapic_routing: irq 21 gsi 21 vector 21 ioapic 0 > pin 21 triggering 1 polarity 1 > [ 18.215560] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 21 (level, low) -> > IRQ 21 > [ 18.301142] ehci_hcd 0000:00:1a.0: EHCI Host Controller > [ 18.364179] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus > number 1 > [ 18.456986] ehci_hcd 0000:00:1a.0: debug port 2 > [ 18.511435] ehci_hcd 0000:00:1a.0: irq 21, io mem 0xce003000 > [ 18.589288] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 > [ 18.658307] usb usb1: New USB device found, idVendor=1d6b, > idProduct=0002 > [ 18.739739] usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 18.826521] usb usb1: Product: EHCI Host Controller > [ 18.885035] usb usb1: Manufacturer: Linux 2.6.31.13 ehci_hcd > [ 18.952915] usb usb1: SerialNumber: 0000:00:1a.0 > [ 19.008822] usb usb1: configuration #1 chosen from 1 choice > [ 19.076102] hub 1-0:1.0: USB hub found > [ 19.121247] hub 1-0:1.0: 2 ports detected > [ 19.169523] xen_set_ioapic_routing: irq 20 gsi 20 vector 20 ioapic 0 > pin 20 triggering 1 polarity 1 > [ 19.278107] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> > IRQ 20 > [ 19.363693] ehci_hcd 0000:00:1d.0: EHCI Host Controller > [ 19.426837] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus > number 2 > [ 19.519665] ehci_hcd 0000:00:1d.0: debug port 2 > [ 19.574137] ehci_hcd 0000:00:1d.0: irq 20, io mem 0xce004000 > [ 20.413312] usb 1-1: new high speed USB device using ehci_hcd and > address 2 > [ 19.760373] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 > [ 19.829381] usb usb2: New USB device found, idVendor=1d6b, > idProduct=0002 > [ 19.910786] usb usb2: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 19.997491] usb usb2: Product: EHCI Host Controller > [ 20.056022] usb usb2: Manufacturer: Linux 2.6.31.13 ehci_hcd > [ 20.123938] usb usb2: SerialNumber: 0000:00:1d.0 > [ 20.179767] usb usb2: configuration #1 chosen from 1 choice > [ 35.261351] usb 1-1: New USB device found, idVendor=8087, > idProduct=0020 > [ 35.261353] usb 1-1: New USB device strings: Mfr=0, Product=0, > SerialNumber=0 > [ 35.261696] usb 1-1: configuration #1 chosen from 1 choice > [ 35.262004] hub 1-1:1.0: USB hub found > [ 35.262112] hub 1-1:1.0: 6 ports detected > [ 20.571877] hub 2-0:1.0: USB hub found > [ 20.616947] hub 2-0:1.0: 2 ports detected > [ 20.665554] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > [ 20.740168] uhci_hcd: USB Universal Host Controller Interface driver > [ 20.817277] usbcore: registered new interface driver usblp > [ 20.883086] Initializing USB Mass Storage driver... > [ 20.941974] usbcore: registered new interface driver usb-storage > [ 21.014026] USB Mass Storage support registered. > [ 36.112936] usb 2-1: new high speed USB device using ehci_hcd and > address 2 > [ 21.153280] usbcore: registered new interface driver libusual > [ 36.228304] usb 2-1: New USB device found, idVendor=8087, > idProduct=0020 > [ 36.228307] usb 2-1: New USB device strings: Mfr=0, Product=0, > SerialNumber=0 > [ 36.228660] usb 2-1: configuration #1 chosen from 1 choice > [ 36.228969] hub 2-1:1.0: USB hub found > [ 36.229070] hub 2-1:1.0: 8 ports detected > [ 36.495535] usb 2-1.4: new low speed USB device using ehci_hcd and > address 3 > [ 36.592902] usb 2-1.4: New USB device found, idVendor=04d9, > idProduct=1603 > [ 36.592905] usb 2-1.4: New USB device strings: Mfr=1, Product=2, > SerialNumber=0 > [ 36.592908] usb 2-1.4: Product: USB Keyboard > [ 36.592910] usb 2-1.4: Manufacturer: > [ 36.593255] usb 2-1.4: configuration #1 chosen from 1 choice > [ 36.657328] usb 2-1.5: new full speed USB device using ehci_hcd and > address 4 > [ 36.735047] usb 2-1.5: New USB device found, idVendor=0000, > idProduct=0000 > [ 36.735049] usb 2-1.5: New USB device strings: Mfr=1, Product=2, > SerialNumber=3 > [ 36.735052] usb 2-1.5: Product: iRMC USB Device > [ 36.735054] usb 2-1.5: Manufacturer: Fujitsu > [ 36.735056] usb 2-1.5: SerialNumber: 600ABC94D3074C > [ 36.735417] usb 2-1.5: configuration #1 chosen from 1 choice > [ 22.454959] PNP: No PS/2 controller found. Probing ports directly. > [ 23.293431] hrtimer: interrupt took 9183132 ns > [ 22.842002] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 22.902741] mice: PS/2 mouse device common for all mice > [ 22.977135] rtc_cmos 00:06: RTC can wake from S4 > [ 23.032918] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0 > [ 23.106105] rtc0: alarms up to one month, y3k, 114 bytes nvram > [ 23.176478] xen_allocate_pirq: returning irq 20 for gsi 20 > [ 23.242289] xen_set_ioapic_routing: irq 20 gsi 20 vector 20 ioapic 0 > pin 20 triggering 1 polarity 1 > [ 23.350973] i801_smbus 0000:00:1f.3: PCI INT D -> GSI 20 (level, low) > -> IRQ 20 > [ 23.440784] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) > initialised: [5]dm-devel@xxxxxxxxxx > [ 23.542605] cpuidle: using governor ladder > [ 23.591833] cpuidle: using governor menu > [ 23.642069] usbcore: registered new interface driver hiddev > [ 38.781806] input: USB Keyboard as > /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input3 > [ 38.899189] generic-usb 0003:04D9:1603.0001: input,hidraw0: USB HID > v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.0-1.4/input0 > [ 39.057332] input: USB Keyboard as > /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.1/input/input4 > [ 39.174832] generic-usb 0003:04D9:1603.0002: input,hidraw1: USB HID > v1.10 Device [ USB Keyboard] on usb-0000:00:1d.0-1.4/input1 > [ 39.315677] input: Fujitsu iRMC USB Device as > /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input5 > [ 39.442738] generic-usb 0003:0000:0000.0003: input,hidraw2: USB HID > v1.11 Keyboard [Fujitsu iRMC USB Device] on usb-0000:00:1d.0-1.5/input0 > [ 39.594713] input: Fujitsu iRMC USB Device as > /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.1/input/input6 > [ 39.722047] generic-usb 0003:0000:0000.0004: input,hidraw3: USB HID > v1.11 Mouse [Fujitsu iRMC USB Device] on usb-0000:00:1d.0-1.5/input1 > [ 39.869436] usbcore: registered new interface driver usbhid > [ 39.936280] usbhid: v2.6:USB HID core driver > [ 39.988359] Advanced Linux Sound Architecture Driver Version 1.0.20. > [ 40.066220] ALSA device list: > [ 40.101937] No soundcards found. > [ 40.142841] Netfilter messages via NETLINK v0.30. > [ 40.199352] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) > [ 40.273258] ctnetlink v0.93: registering with nfnetlink. > [ 40.338192] ip_tables: (C) 2000-2006 Netfilter Core Team > [ 40.402000] TCP cubic registered > [ 40.440827] Initializing XFRM netlink socket > [ 40.493211] NET: Registered protocol family 10 > [ 40.549310] ip6_tables: (C) 2000-2006 Netfilter Core Team > [ 40.614164] IPv6 over IPv4 tunneling driver > [ 40.666254] NET: Registered protocol family 17 > [ 40.720665] RPC: Registered udp transport module. > [ 40.777108] RPC: Registered tcp transport module. > [ 40.834214] SCTP: Hash tables configured (established 65536 bind 65536) > [ 40.914548] Using IPI No-Shortcut mode > [ 40.960325] registered taskstats version 1 > [ 41.009654] Magic number: 6:500:752 > [ 41.053698] tty ttyS3: hash matches > [ 41.095785] md: Waiting for all devices to be available before > autodetect > [ 41.177190] md: If you don't use raid, use raid=noautodetect > [ 41.245761] md: Autodetecting RAID arrays. > [ 41.294919] md: Scanned 0 and added 0 devices. > [ 41.348234] md: autorun ... > [ 41.381789] md: ... autorun DONE. > [ 41.421739] Root-NFS: No NFS server available, giving up. > [ 41.486540] VFS: Unable to mount root fs via NFS, trying floppy. > [ 41.559115] VFS: Cannot open root device "sda1" or unknown-block(2,0) > [ 41.636362] Please append a correct "root=" boot option; here are the > available partitions: > [ 41.736610] 0b00 1048575 sr0 driver: sr > [ 41.791146] Kernel panic - not syncing: VFS: Unable to mount root fs on > unknown-block(2,0) > [ 41.890337] Pid: 1, comm: swapper Not tainted 2.6.31.13 #2 > [ 41.956135] Call Trace: > [ 41.985599] [<c15e8386>] ? printk+0xf/0x11 > [ 42.035826] [<c15e82ca>] panic+0x39/0xe6 > [ 42.083950] [<c191ec2d>] mount_block_root+0x163/0x172 > [ 42.145673] [<c1002930>] ? hypercall_page+0x930/0x1005 > [ 42.208414] [<c191eca2>] mount_root+0x66/0x84 > [ 42.261803] [<c191ee05>] prepare_namespace+0x145/0x16c > [ 42.324489] [<c191e34f>] kernel_init+0x16e/0x17d > [ 42.380929] [<c191e1e1>] ? kernel_init+0x0/0x17d > [ 42.437369] [<c1028d37>] kernel_thread_helper+0x7/0x10 > > For@ll > > References > > Visible links > 1. mailto:pasik@xxxxxx > 2. mailto:pasik@xxxxxx > 3. http://wiki.xensource.com/xenwiki/XenParavirtOps > 4. mailto:tigran@xxxxxxxxxxxxxxxxxxxx > 5. mailto:dm-devel@xxxxxxxxxx > _______________________________________________ > Xen-users mailing list > Xen-users@xxxxxxxxxxxxxxxxxxx > http://lists.xensource.com/xen-users _______________________________________________ Xen-users mailing list Xen-users@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-users
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |