|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [Xen-users] Problems installing guest domains
Hi,I am trying out Xen for the first time and I am having a few problems with getting it working. The computer is a quad core Intel Xeon with VT enabled, 8gb of RAM and 2 x 15,000rpm SAS drives in RAID1. I have installed CentOS 5 64bit and installed Xen 3.3.0 via yum. I have successfully booted in to dom0. Here is my grub.conf on dom0: # grub.conf generated by anaconda ## Note that you do not have to rerun grub after making changes to this file# NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/sda2 # initrd /initrd-version.img #boot=/dev/sda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.18-92.1.22.el5xen) root (hd0,0) kernel /xen.gz-3.3.0 module /vmlinuz-2.6.18-92.1.22.el5xen ro root=LABEL=/ module /initrd-2.6.18-92.1.22.el5xen.img title CentOS (2.6.18-92.el5) root (hd0,0) kernel /vmlinuz-2.6.18-92.el5 ro root=LABEL=/ initrd /initrd-2.6.18-92.el5.img However, I can't for the life of me install a guest domain. I have been Googling for the last 3 days and I am extremely confused - it seems like there are multiple ways to do it but none are working for me. I am wanting to use file-based HDD's for the guests, and I want to install off an iso of CentOS5 on my HDD for now. First I tried using the "virt-install" script. Firstly, should I be able to install a fully virtualized guest or will only para-virtualized work? I will show what happens when I try both. Firstly, if I try to install it as a paravirtualized guest I am running this command: virt-install -n test1 -r 512 -f /vm/test1.img -s 5 --location=/vm/CentOS-5.2-x86_64-bin-DVD.iso This creates the domain fine and starts what I assume is the CentOS installation - it asks me to first select a language, once I have done that it says "What type of media contains the packages to be installed?" and gives me a list of Local CDROM, Hard drive, NFS, FTP and HTTP. What is this asking me for? If it has already started the installation then surely it knows where to get the packages from? Anyway, if I select Local CDROM it says "Unable to find any devices of the type needed for this installation type. Would you like to manually select your driver or use a driver disk?" I have got no idea what to do from here. If I try to install a fully virtualized guest using virt-install, here is the command I am running: virt-install -n test1 -r 512 -f /vm/test1.img -s 5 --location=/vm/CentOS-5.2-x86_64-bin-DVD.iso --hvm This comes up and it just hangs here: Starting install... Creating storage file... 100% |=========================| 5.0 GB 00:00 Creating domain... 0 B 00:00 â My xend-debug.log file says this: XendInvalidDomain: <Fault 3: 'b5e19b10-7540-902c-b585-f8783447521f'> Traceback (most recent call last):File "/usr/lib64/python2.4/site-packages/xen/web/httpserver.py", line 140, in process resource = self.getResource()File "/usr/lib64/python2.4/site-packages/xen/web/httpserver.py", line 172, in getResource return self.getServer().getResource(self)File "/usr/lib64/python2.4/site-packages/xen/web/httpserver.py", line 351, in getResource return self.root.getRequestResource(req)File "/usr/lib64/python2.4/site-packages/xen/web/resource.py", line 39, in getRequestResource return findResource(self, req)File "/usr/lib64/python2.4/site-packages/xen/web/resource.py", line 26, in findResource next = resource.getPathResource(pathElement, request)File "/usr/lib64/python2.4/site-packages/xen/web/resource.py", line 49, in getPathResource val = self.getChild(path, request)File "/usr/lib64/python2.4/site-packages/xen/web/SrvDir.py", line 71, in getChild val = self.get(x)File "/usr/lib64/python2.4/site-packages/xen/xend/server/SrvDomainDir.py", line 52, in get return self.domain(x)File "/usr/lib64/python2.4/site-packages/xen/xend/server/SrvDomainDir.py", line 44, in domain dom = self.xd.domain_lookup(x)File "/usr/lib64/python2.4/site-packages/xen/xend/XendDomain.py", line 529, in domain_lookup raise XendInvalidDomain(str(domid)) XendInvalidDomain: <Fault 3: 'test1'>So, now I try doing what looks like the manual way - creating a config file in /etc/xen and using xm create. First I create a file for the HDD: dd if=/dev/zero of=test1.img bs=1M count=1 seek=1023 Then I created this config file and placed it at /etc/xen/test: # -*- mode: python; -*- #============================================================================ # Python configuration setup for 'xm create'.# This script sets the parameters used when a domain is created using 'xm create'.# You use a separate script for each domain you want to create, or # you can set the parameters for the domain on the xm command line. #============================================================================ #---------------------------------------------------------------------------- # Kernel image file. kernel = "/boot/vmlinuz-2.6.18-92.1.22.el5xen" # Optional ramdisk. #ramdisk = "/boot/initrd.gz" ramdisk = "/boot/initrd-2.6.18-92.1.22.el5xen.img" #ramdisk = "/boot/initrd-centos5-xen.img" # The domain build function. Default is 'linux'. #builder='linux' # Initial memory allocation (in megabytes) for the new domain. # # WARNING: Creating a domain with insufficient memory may cause out of # memory errors. The domain needs enough memory to boot kernel # and modules. Allocating less than 32MBs is not recommended. memory = 512 # A name for your domain. All domains must have different names. name = "Test1"# 128-bit UUID for the domain. The default behavior is to generate a new UUID# on each call to 'xm create'. #uuid = "06ed00fe-1162-4fc4-b5d8-11993ee4a8b9" # List of which CPUS this domain is allowed to use, default Xen picks #cpus = "" # leave to Xen to pick #cpus = "0" # all vcpus run on CPU0 #cpus = "0-3,5,^1" # all vcpus run on cpus 0,2,3,5 #cpus = ["2", "3"] # VCPU0 runs on CPU2, VCPU1 runs on CPU3 # Number of Virtual CPUS to use, default is 1 #vcpus = 1 #---------------------------------------------------------------------------- # Define network interfaces.# By default, no network interfaces are configured. You may have one created# with sensible defaults using an empty vif clause: # # vif = [ '' ] ## or optionally override backend, bridge, ip, mac, script, type, or vifname:# # vif = [ 'mac=00:16:3e:00:00:11, bridge=xenbr0' ] # # or more than one interface may be configured: # # vif = [ '', 'bridge=xenbr1' ] vif = [ '' ] #---------------------------------------------------------------------------- # Define the disk devices you want the domain to have access to, and # what you want them accessible as. # Each disk entry is of the form phy:UNAME,DEV,MODE # where UNAME is the device, DEV is the device name the domain will see, # and MODE is r for read-only, w for read-write. #disk = [ 'phy:hda1,hda1,w' ]#disk = [ 'file:/vm/test1.img,ioemu:sda1,w', 'phy:/dev/cdrom,hdc:cdrom,r' ]disk = [ 'file:/vm/test1.img,ioemu:sda1,w' ] #---------------------------------------------------------------------------- # Define frame buffer device. # # By default, no frame buffer device is configured. # # To create one using the SDL backend and sensible defaults: # # vfb = [ 'type=sdl' ] # # This uses environment variables XAUTHORITY and DISPLAY. You # can override that: # # vfb = [ 'type=sdl,xauthority=/home/bozo/.Xauthority,display=:1' ] # # To create one using the VNC backend and sensible defaults: # # vfb = [ 'type=vnc' ] # # The backend listens on 127.0.0.1 port 5900+N by default, where N is # the domain ID. You can override both address and N: # # vfb = [ 'type=vnc,vnclisten=127.0.0.1,vncdisplay=1' ] # # Or you can bind the first unused port above 5900: # # vfb = [ 'type=vnc,vnclisten=0.0.0.0,vncunused=1' ] # # You can override the password: # # vfb = [ 'type=vnc,vncpasswd=MYPASSWD' ] # # Empty password disables authentication. Defaults to the vncpasswd # configured in xend-config.sxp. #---------------------------------------------------------------------------- # Define to which TPM instance the user domain should communicate. # The vtpm entry is of the form 'instance=INSTANCE,backend=DOM' # where INSTANCE indicates the instance number of the TPM the VM # should be talking to and DOM provides the domain where the backend # is located. # Note that no two virtual machines should try to connect to the same # TPM instance. The handling of all TPM instances does require # some management effort in so far that VM configration files (and thus # a VM) should be associated with a TPM instance throughout the lifetime # of the VM / VM configuration file. The instance number must be # greater or equal to 1. #vtpm = [ 'instance=1,backend=0' ] #---------------------------------------------------------------------------- # Set the kernel command line for the new domain. # You only need to define the IP parameters and hostname if the domain's # IP config doesn't, e.g. in ifcfg-eth0 or via DHCP. # You can use 'extra' to set the runlevel and custom environment # variables used by custom rc scripts (e.g. VMID=, usr= ). # Set if you want dhcp to allocate the IP address. #dhcp="dhcp" # Set netmask. #netmask= # Set default gateway. #gateway= # Set the hostname. #hostname= "vm%d" % vmid # Set root device. root = "/dev/sda1 ro" # Root device for nfs. #root = "/dev/nfs" # The nfs server. #nfs_server = '192.0.2.1' # Root directory on the nfs server. #nfs_root = '/full/path/to/root/directory' # Sets runlevel 4. extra = "4" #---------------------------------------------------------------------------- # Configure the behaviour when a domain exits. There are three 'reasons' # for a domain to stop: poweroff, reboot, and crash. For each of these you # may specify: # # "destroy", meaning that the domain is cleaned up as normal; # "restart", meaning that a new domain is started in place of the old # one; # "preserve", meaning that no clean-up is done until the domain is # manually destroyed (using xm destroy, for example); or # "rename-restart", meaning that the old domain is not cleaned up, but is # renamed and a new domain started in its place. ## In the event a domain stops due to a crash, you have the additional options:## "coredump-destroy", meaning dump the crashed domain's core and then destroy; # "coredump-restart', meaning dump the crashed domain's core and the restart.# # The default is # # on_poweroff = 'destroy' # on_reboot = 'restart' # on_crash = 'restart' ## For backwards compatibility we also support the deprecated option restart# # restart = 'onreboot' means on_poweroff = 'destroy' # on_reboot = 'restart' # on_crash = 'destroy' # # restart = 'always' means on_poweroff = 'restart' # on_reboot = 'restart' # on_crash = 'restart' # # restart = 'never' means on_poweroff = 'destroy' # on_reboot = 'destroy' # on_crash = 'destroy' #on_poweroff = 'destroy' #on_reboot = 'restart' #on_crash = 'restart' #----------------------------------------------------------------------------- # Configure PVSCSI devices: # #vscsi=[ 'PDEV, VDEV' ] # # PDEV gives physical SCSI device to be attached to specified guest # domain by one of the following identifier format. # - XX:XX:XX:XX (4-tuples with decimal notation which shows # "host:channel:target:lun") # - /dev/sdxx or sdx # - /dev/stxx or stx # - /dev/sgxx or sgx # - result of 'scsi_id -gu -s'. # ex. # scsi_id -gu -s /block/sdb # 36000b5d0006a0000006a0257004c0000 # # VDEV gives virtual SCSI device by 4-tuples (XX:XX:XX:XX) as # which the specified guest domain recognize. # #vscsi = [ '/dev/sdx, 0:0:0:0' ] #============================================================================ I then ran this command: xm create -c test1 And this is the last few lines of the output before it stops: Scanning and configuring dmraid supported devices Creating root device. Mounting root filesystem. mount: could not find filesystem '/dev/root' Setting up other filesystems. Setting up new root fs setuproot: moving /dev failed: No such file or directory no fstab.sys, mounting internal defaults setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys switchroot: mount failed: No such file or directory Kernel panic - not syncing: Attempted to kill init! So I am utterly stumped and extremely frustrated by now that I cannot get something that is seemingly simple to work! Any advise and help would be very greatly appreciated! Thanks in advance :) Andrew _______________________________________________ Xen-users mailing list Xen-users@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-users
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |