[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Xen-users] define ip gateway
- To: "Janis Daniel Bistevins" <bistevins@xxxxxxxxx>
- From: "Todd Deshane" <deshantm@xxxxxxxxx>
- Date: Wed, 16 Jan 2008 10:27:23 -0500
- Cc: xen-users@xxxxxxxxxxxxxxxxxxx
- Delivery-date: Wed, 16 Jan 2008 07:27:56 -0800
- Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=message-id:date:from:reply-to:to:subject:cc:in-reply-to:mime-version:content-type:references; b=SKUx+W0+S3RgKkawBsX3kL5ieVpGBp0k1KjaYMKY00abq0UUjVx76UX9W6IIwSX0FljiFWybmL8Y7mgZNEyrVdnDKuuazIhSPO8GoQJu3cMYMqIdc2VJJeli7w/KkD8v3FsjxFMeNdYAuwcs+7ZosMys+/EE5McJBjqgitqNXf4=
- List-id: Xen user discussion <xen-users.lists.xensource.com>
On Jan 16, 2008 10:10 AM, Janis Daniel Bistevins < bistevins@xxxxxxxxx> wrote:
hi,
I have a VM with route-nat and 3 virtual interfaces. This is my config:
vif = [ 'ip=10.10.10.4/24, vifname=vif1.0', 'ip=
10.10.20.4/24,
vifname=vif2.0', 'ip=10.10.30.4/24, vifname=vif3.0' ]
And the output of dom0 ifconfig:
vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet addr:10.10.10.131 Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet addr:10.10.20.131 Bcast:
0.0.0.0 Mask:255.255.255.255
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
vif3.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet addr:
10.10.30.131 Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
I need to know how can I change the IP address of vifx.0
. I want to
set that address to
something like 10.10.10.1 or 10.10.20.1, not
10.10.10.131.
Where can I change that 131 to something else? and why is assigned like that?
If my understanding is correct, since you set the guest IP to 10.10.10.4
the vifx.0 gets 10.10.10.131 since Xen adds 127 to the 4 (127+4 = 131). That is just the backend and you will not use that IP, you should only be concerned with the frontend number i.e
. 10.10.10.4 which you set in the config. Regards, Todd
thx in advance.
--
Janis Daniel Bistevins
---
Serenity now!!!
---
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
