Re: [Xen-users] Debian Etch: Error: Device 0 (vif) could not be connected. Hotplug scripts not working.

[Dan Goscomb <dgoscomb@xxxxxxxxxxxxx>]

does anyone have any more ideas on this? its causing a real headache and
happens on 3 different servers (all AMD64).

Cheers

Dan

On Fri, 2007-08-24 at 19:54 +0530, trilok nuwal wrote:
> 
> you shoud put in yr config file then try.
> 
> vif  = [ 'bridge=xenbr2' ]
> 
> 
> 
> On 8/24/07, Dan Goscomb <dgoscomb@xxxxxxxxxxxxx> wrote:
>         Hi
>         
>         The bridges work for some DomU... as I said... the bridge is
>         automatically created:
>         
>         vps2:~# brctl show
>         bridge name     bridge id               STP enabled
>         interfaces
>         xenbr2          8000.feffffffffff       no              vif0.2
>                                                                 peth2
>                                                                 vif15.0
>                                                                 vif2.0 
>                                                                 vif4.0
>                                                                 vif11.0
>                                                                 vif6.0
>         
>         vif13.0
>                                                                 vif14.0
>         
>         
>         Config file of one of the DomU:
>         
>         kernel  = '/boot/vmlinuz-2.6.18-4-xen-amd64'
>         ramdisk = '/boot/initrd.img-2.6.18-4-xen-amd64 '
>         memory  = '128'
>         root    = '/dev/sda1 ro'
>         disk    = [ 'phy:vg0/domu-disk,sda1,w',
>         'phy:vg0/domu-swap,sda2,w' ]
>         name    = 'domu'
>         vif  = [ 'ip=<IP_ADDRESS>' ] 
>         on_poweroff = 'destroy'
>         on_reboot   = 'restart'
>         on_crash    = 'restart'
>         
>         
>         Cheers
>         
>         Dan
>         
>         
>         On Fri, 2007-08-24 at 19:45 +0530, trilok nuwal wrote:
>         > better post the config file as well as #ifconfig output in
>         dom0. 
>         >
>         > On 8/24/07, trilok nuwal <tc.nuwal@xxxxxxxxx > wrote:
>         >         Did you created bridges in dom0 whtever u r
>         exporting to domU.
>         >
>         >
>         >
>         >
>         >         On 8/24/07, Dan Goscomb <dgoscomb@xxxxxxxxxxxxx>
>         wrote:
>         >                 Hi All
>         >
>         >                 We have an issue whereby after X number
>         (where X can
>         >                 change) DomU are
>         >                 booted, subsequent ones fail with the error
>         message in
>         >                 the title.
>         >
>         >                 Is this a known issue? I have been unable to
>         work out
>         >                 why that error
>         >                 message is appearing...
>         >
>         >                 Any hints would be appreciated!
>         >
>         >                 Cheers
>         >
>         >                 Dan
>         >
>         >
>         >
>         _______________________________________________
>         >                 Xen-users mailing list
>         >                 Xen-users@xxxxxxxxxxxxxxxxxxx
>         >                 http://lists.xensource.com/xen-users
>         >
>         >
>         >
>         
> 
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users


_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users