|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [Xen-users] Paravirtualization, new installation from cdrom
Is it possible to do a fresh install from a cd in paravirtualization mode ? just like the full virtualization, where you tell where's your iso and then you boot and install the new OS if it's possible, what's the problem here, here's my boot.msg and my xen domain config file. I'm running SLES 10 beta 11 x64 and I'm trying to use the yast2 xen module to install this new vm and I'm trying to install sles 10 beta 11 x64 ( the same version as Dom0 ). now the installation seem to boot but i'm unable to install anything since the installation is unable to acces the cdrom.. # xm list Name ID Mem(MiB) VCPUs State Time(s) DEB32-HVM 5 1000 1 -b---- 2520.2 Domain-0 0 1995 16 r----- 19643.0 WindowsXP-HVM 6 1000 1 -b---- 344.9 debianrs 7 128 1 -b---- 24.9 vm1 12 256 1 -b---- 5.1 ==================================== # cat vm/vm1 disk = [ 'file:/mnt/mv/vm1/hda,hda,w', 'phy:sr0,hdb,r' ] memory = 256 vcpus = 1 builder = 'linux' kernel = '/tmp/YaST2-10396-6vObw7/vmlinuz-2.6.16.11-7-xen' ramdisk = '/tmp/YaST2-10396-6vObw7/inst-initrd' name = 'vm1' vif = [ 'mac=00:16:3e:14:a8:b7' ] localtime = 0 extra = 'install=/dev/sr0 TERM=xterm textmode=1' ==================================== # cat /var/log/boot.msg Inspecting /boot/System.map-2.6.16.11-7-xen Loaded 21826 symbols from /boot/System.map-2.6.16.11-7-xen. Symbols match kernel version 2.6.16. No module symbols loaded - kernel modules not enabled. klogd 1.4.1, log source = ksyslog started. <4>Bootdata ok (command line is root=/dev/sdb5 vga=0x31a resume=/dev/sda2 splash=silent showopts) <5>Linux version 2.6.16.11-7-xen (geeko@buildhost) (gcc version 4.1.0 (SUSE Linux)) #1 SMP Wed Apr 26 06:58:16 UTC 2006 <7>On node 0 totalpages: 514048 <7> DMA zone: 514048 pages, LIFO batch:31 <7> DMA32 zone: 0 pages, LIFO batch:0 <7> Normal zone: 0 pages, LIFO batch:0 <7> HighMem zone: 0 pages, LIFO batch:0 <7>ACPI: RSDP (v002 INTEL ) @ 0x00000000000f03d0 <7>ACPI: XSDT (v001 INTEL SHW40 0x00000002 MSFT 0x01000013) @ 0x000000007fb31f30 <7>ACPI: FADT (v003 INTEL SHW40 0x00000002 0x00000000) @ 0x000000007fb2fd90 <7>ACPI: MADT (v001 INTEL SHW40 0x00000002 0x00000000) @ 0x000000007fb2fc10 <7>ACPI: SRAT (v001 INTEL SHW40 0x00000002 0x00000000) @ 0x000000007fb20f90 <7>ACPI: MCFG (v001 INTEL SHW40 0x00000002 0x00000000) @ 0x000000007fb20f10 <7>ACPI: SPCR (v001 INTEL SHW40 0x00000002 0x00000000) @ 0x000000007fb20e90 <7>ACPI: SSDT (v001 INTEL SHW40 0x00004000 INTL 0x20030918) @ 0x000000007fb1e010 <7>ACPI: SSDT (v001 INTEL SHW40 0x00004004 INTL 0x20030918) @ 0x000000007fb1c010 <7>ACPI: SSDT (v001 INTEL SHW40 0x00004008 INTL 0x20030918) @ 0x000000007fb1a010 <7>ACPI: SSDT (v001 INTEL SHW40 0x0000400c INTL 0x20030918) @ 0x000000007fb18010 <7>ACPI: DSDT (v001 INTEL SHW40 0x00000002 INTL 0x20030918) @ 0x0000000000000000 <7>ACPI: Local APIC address 0xfee00000 <6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x08] enabled) <6>ACPI: LAPIC (acpi_id[0x04] lapic_id[0x0e] enabled) <6>ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] enabled) <6>ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x06] enabled) <6>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x0a] enabled) <6>ACPI: LAPIC (acpi_id[0x06] lapic_id[0x0c] enabled) <6>ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x02] enabled) <6>ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x04] enabled) <6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x09] enabled) <6>ACPI: LAPIC (acpi_id[0x05] lapic_id[0x0f] enabled) <6>ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) <6>ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x07] enabled) <6>ACPI: LAPIC (acpi_id[0x03] lapic_id[0x0b] enabled) <6>ACPI: LAPIC (acpi_id[0x07] lapic_id[0x0d] enabled) <6>ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) <6>ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x05] enabled) <6>ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1]) <6>ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) <6>ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) <6>IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 <6>ACPI: IOAPIC (id[0x09] address[0xfec85000] gsi_base[24]) <6>IOAPIC[1]: apic_id 9, version 32, address 0xfec85000, GSI 24-47 <6>ACPI: IOAPIC (id[0x0a] address[0xfec85800] gsi_base[48]) <6>IOAPIC[2]: apic_id 10, version 32, address 0xfec85800, GSI 48-71 <6>ACPI: IOAPIC (id[0x0b] address[0xfec86000] gsi_base[72]) <6>IOAPIC[3]: apic_id 11, version 32, address 0xfec86000, GSI 72-95 <6>ACPI: IOAPIC (id[0x0c] address[0xfec86800] gsi_base[96]) <6>IOAPIC[4]: apic_id 12, version 32, address 0xfec86800, GSI 96-119 <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) <7>ACPI: IRQ0 used by override. <7>ACPI: IRQ2 used by override. <7>ACPI: IRQ9 used by override. <6>Setting APIC routing to xen <6>Using ACPI (MADT) for SMP configuration information <6>Allocating PCI resources starting at 80000000 (gap: 7fc00000:803a0000) <4>Built 1 zonelists <5>Kernel command line: root=/dev/sdb5 vga=0x31a resume=/dev/sda2 splash=silent showopts <6>bootsplash: silent mode. <4>Initializing CPU#0 <4>PID hash table entries: 4096 (order: 12, 131072 bytes) <6>Xen reported: 2992.500 MHz processor. <4>Console: colour VGA+ 80x25 <4>Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) <4>Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>Software IO TLB enabled: <4> Aperture: 64 megabytes <4> Bus range: 0x0000000078000000 - 0x000000007c000000 <4> Kernel range: 0xffff8800036b9000 - 0xffff8800076b9000 <6>PCI-DMA: Using software bounce buffering for IO (SWIOTLB) <4>Memory: 1930240k/2056192k available (1848k kernel code, 125424k reserved, 782k data, 140k init) <4>Calibrating delay using timer specific routine.. 7485.14 BogoMIPS (lpj=14970294) <6>Security Framework v1.0.0 initialized <4>Mount-cache hash table entries: 256 <6>CPU: Trace cache: 12K uops, L1 D cache: 16K <6>CPU: L2 cache: 2048K <6>CPU: Physical Processor ID: 0 <6>CPU: Processor Core ID: 0 <6>checking if image is initramfs... it is <4>Freeing initrd memory: 7193k freed <4>Initializing CPU#1 <4>Initializing CPU#2 <4>Initializing CPU#3 <4>Initializing CPU#4 <4>Initializing CPU#5 <4>Initializing CPU#6 <4>Initializing CPU#7 <4>Initializing CPU#8 <4>Initializing CPU#9 <4>Initializing CPU#10 <4>Initializing CPU#11 <4>Initializing CPU#12 <4>Initializing CPU#13 <4>Initializing CPU#14 <6>Brought up 16 CPUs <4>Initializing CPU#15 <4>migration_cost=1826 <6>DMI 2.3 present. <4>Grant table initialized <6>NET: Registered protocol family 16 <6>ACPI: bus type pci registered <6>PCI: Using configuration type 1 <6>PCI: Using MMCONFIG at 80000000 <6>ACPI: Subsystem revision 20060127 <4>ACPI Error (evgpeblk-0284): Unknown GPE method type: NTF_ (name not of form _Lxx or _Exx) [20060127] <4>ACPI Error (evgpeblk-0284): Unknown GPE method type: PNTS (name not of form _Lxx or _Exx) [20060127] <6>ACPI: Interpreter enabled <6>ACPI: Using IOAPIC for interrupt routing <6>ACPI: PCI Root Bridge [TNB] (0000:00) <7>PCI: Probing PCI hardware (bus 00) <4>PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO <4>PCI quirk: region 0480-04bf claimed by ICH4 GPIO <6>PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2 <4>PCI: PXH quirk detected, disabling MSI for SHPC device <4>PCI: PXH quirk detected, disabling MSI for SHPC device <7>Boot video device is 0000:16:00.0 <6>PCI: Transparent bridge - 0000:00:1e.0 <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.ICHB._PRT] <4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12) <4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12) <4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12) <4>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11 12) <4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. <4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. <4>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. <4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 7 9 10 11 12) <6>ACPI: Embedded Controller [EC0] (gpe 16) interrupt mode. <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI1._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI2._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI4._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI5._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI6._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI6.PXHA._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI6.PXHB._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI7.PXHA._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.TNB_.PCI7.PXHB._PRT] <4>ACPI: Device [M1] status [0000000c]: functional but not present; setting present <4>ACPI: Device [M2] status [0000000c]: functional but not present; setting present <4>ACPI: Device [M3] status [0000000c]: functional but not present; setting present <4>ACPI: Device [M4] status [0000000c]: functional but not present; setting present <4>ACPI: Device [M5] status [0000000c]: functional but not present; setting present <6>xen_mem: Initialising balloon driver. <6>PCI: Using ACPI for IRQ routing <6>PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report <4>TC classifier action (bugs to netdev@xxxxxxxxxxxxxxx cc hadi@xxxxxxxxxx) <6>PCI: Bridge: 0000:00:01.0 <6> IO window: 8000-8fff <6> MEM window: b6000000-b7ffffff <6> PREFETCH window: 98000000-9bffffff <6>PCI: Bridge: 0000:00:02.0 <6> IO window: 7000-7fff <6> MEM window: b4000000-b5ffffff <6> PREFETCH window: 9c000000-9fffffff <6>PCI: Bridge: 0000:00:03.0 <6> IO window: disabled. <6> MEM window: disabled. <6> PREFETCH window: disabled. <6>PCI: Bridge: 0000:00:04.0 <6> IO window: 6000-6fff <6> MEM window: b2000000-b3ffffff <6> PREFETCH window: a0000000-a3ffffff <6>PCI: Bridge: 0000:00:05.0 <6> IO window: 5000-5fff <6> MEM window: b0000000-b1ffffff <6> PREFETCH window: a4000000-a7ffffff <3>PCI: Failed to allocate mem resource #9:100000@ac000000 for 0000:0e:00.2 <6>PCI: Bridge: 0000:0e:00.0 <6> IO window: 4000-4fff <6> MEM window: ac000000-adffffff <6> PREFETCH window: a8000000-abffffff <6>PCI: Bridge: 0000:0e:00.2 <6> IO window: disabled. <6> MEM window: ae000000-ae0fffff <6> PREFETCH window: disabled. <6>PCI: Bridge: 0000:00:06.0 <6> IO window: 4000-4fff <6> MEM window: ac000000-ae1fffff <6> PREFETCH window: a8000000-abffffff <6>PCI: Bridge: 0000:13:00.0 <6> IO window: 3000-3fff <6> MEM window: b8100000-b81fffff <6> PREFETCH window: 80000000-801fffff <6>PCI: Bridge: 0000:13: 00.2 <6> IO window: disabled. <6> MEM window: disabled. <6> PREFETCH window: disabled. <6>PCI: Bridge: 0000:00:07.0 <6> IO window: 3000-3fff <6> MEM window: b8100000-b82fffff <6> PREFETCH window: 80000000-801fffff <6>PCI: Bridge: 0000:00:1e.0 <6> IO window: 2000-2fff <6> MEM window: b8000000-b80fffff <6> PREFETCH window: 90000000-97ffffff <7>PCI: Setting latency timer of device 0000:00: 01.0 to 64 <7>PCI: Setting latency timer of device 0000:00:02.0 to 64 <7>PCI: Setting latency timer of device 0000:00:03.0 to 64 <7>PCI: Setting latency timer of device 0000:00:04.0 to 64 <7>PCI: Setting latency timer of device 0000:00: 05.0 to 64 <7>PCI: Setting latency timer of device 0000:00:06.0 to 64 <6>GSI 16 sharing vector 0xA0 and IRQ 16 <6>ACPI: PCI Interrupt 0000:0e:00.0[A] -> GSI 47 (level, low) -> IRQ 16 <7>PCI: Setting latency timer of device 0000:0e: 00.0 to 64 <7>PCI: Setting latency timer of device 0000:0e:00.2 to 64 <7>PCI: Setting latency timer of device 0000:00:07.0 to 64 <7>PCI: Setting latency timer of device 0000:13:00.0 to 64 <7>PCI: Setting latency timer of device 0000:13: 00.2 to 64 <7>PCI: Setting latency timer of device 0000:00:1e.0 to 64 <4>IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ <6>audit: initializing netlink socket (disabled) <5>audit( 1146758870.592:1): initialized <5>VFS: Disk quotas dquot_6.5.1 <4>Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>Initializing Cryptographic API <6>io scheduler noop registered <6>io scheduler anticipatory registered <6>io scheduler deadline registered <6>io scheduler cfq registered (default) <7>PCI: Setting latency timer of device 0000:00:01.0 to 64 <4>pcie_portdrv_probe->Dev[2601:8086] has invalid IRQ. Check vendor BIOS <4>assign_interrupt_mode Found MSI capability <7>Allocate Port Service[0000:00:01.0:pcie00] <7>Allocate Port Service[0000:00:01.0:pcie01] <7>Allocate Port Service[0000:00:01.0:pcie02] <7>PCI: Setting latency timer of device 0000:00:02.0 to 64 <4>pcie_portdrv_probe->Dev[2608:8086] has invalid IRQ. Check vendor BIOS <4>assign_interrupt_mode Found MSI capability <7>Allocate Port Service[0000:00: 02.0:pcie00] <7>Allocate Port Service[0000:00:02.0:pcie01] <7>Allocate Port Service[0000:00:02.0:pcie02] <7>PCI: Setting latency timer of device 0000:00:03.0 to 64 <4>pcie_portdrv_probe->Dev[2603:8086] has invalid IRQ. Check vendor BIOS <4>assign_interrupt_mode Found MSI capability <7>Allocate Port Service[0000:00:03.0:pcie00] <7>Allocate Port Service[0000:00:03.0:pcie01] <7>PCI: Setting latency timer of device 0000:00: 04.0 to 64 <4>pcie_portdrv_probe->Dev[2604:8086] has invalid IRQ. Check vendor BIOS <4>assign_interrupt_mode Found MSI capability <7>Allocate Port Service[0000:00:04.0:pcie00] <7>Allocate Port Service[0000:00: 04.0:pcie01] <7>Allocate Port Service[0000:00:04.0:pcie02] <7>PCI: Setting latency timer of device 0000:00:05.0 to 64 <4>pcie_portdrv_probe->Dev[2605:8086] has invalid IRQ. Check vendor BIOS <4>assign_interrupt_mode Found MSI capability <7>Allocate Port Service[0000:00:05.0:pcie00] <7>Allocate Port Service[0000:00:05.0:pcie01] <7>Allocate Port Service[0000:00:05.0:pcie02] <7>PCI: Setting latency timer of device 0000:00: 06.0 to 64 <4>pcie_portdrv_probe->Dev[2606:8086] has invalid IRQ. Check vendor BIOS <4>assign_interrupt_mode Found MSI capability <7>Allocate Port Service[0000:00:06.0:pcie00] <7>Allocate Port Service[0000:00: 06.0:pcie01] <7>PCI: Setting latency timer of device 0000:00:07.0 to 64 <4>pcie_portdrv_probe->Dev[2607:8086] has invalid IRQ. Check vendor BIOS <4>assign_interrupt_mode Found MSI capability <7>Allocate Port Service[0000:00:07.0:pcie00] <7>Allocate Port Service[0000:00:07.0:pcie01] <6>Real Time Clock Driver v1.12ac <6>Non-volatile memory driver v1.2 <6>Linux agpgart interface v0.101 (c) Dave Jones <6>serio: i8042 AUX port at 0x60,0x64 irq 12 <6>serio: i8042 KBD port at 0x60,0x64 irq 1 <4>isa bounce pool size: 16 pages <4>RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize <4>Xen virtual console successfully installed as ttyS0 <4>Event-channel device installed. <6>mice: PS/2 mouse device common for all mice <6>input: PC Speaker as /class/input/input0 <6>md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 <6>md: bitmap version 4.39 <6>NET: Registered protocol family 2 <4>IP route cache hash table entries: 65536 (order: 7, 524288 bytes) <4>TCP established hash table entries: 262144 (order: 10, 4194304 bytes) <4>TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) <6>TCP: Hash tables configured (established 262144 bind 65536) <6>TCP reno registered <6>NET: Registered protocol family 1 <4>Write protecting the kernel read-only data: 328k <5>SCSI subsystem initialized <4>Driver 'sd' needs updating - please use bus_type methods <7>libata version 1.20 loaded. <7>ata_piix 0000:00:1f.2: version 1.05 <7>ata_pci_init_one: pci_dev class+intf: 0x1018a <7>ata_pci_init_one: NO_LEGACY == 0 <6>GSI 17 sharing vector 0xA8 and IRQ 17 <6>ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17 <7>PCI: Setting latency timer of device 0000:00:1f.2 to 64 <6>ata1: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x9080 irq 14 <7>ata1: dev 0 cfg 00:85c0 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407 93:0000 <6>ata1: dev 0 ATAPI, max UDMA/33 <7>ata_acpi_push_id: skipping for PATA mode <6>ata1: dev 0 configured for UDMA/33 <7>pata_get_dev_handle: ENTER: dev->bus_id='0000:00:1f.2' <7>pata_get_dev_handle: dev_handle: 0x0000000000000000, parent_handle: 0xffff880000f49d40 <7>pata_get_dev_handle: for dev=0x1f.2, addr=0x1f0002, parent=0xffff8800005ff800, *handle=0x0000000000000000 <6>scsi0 : ata_piix <5> Vendor: QSI Model: DVD-ROM SDR-083 Rev: MX13 <5> Type: CD-ROM ANSI SCSI revision: 05 <7>pata_get_dev_handle: ENTER: dev->bus_id='0000:00: 1f.2' <7>pata_get_dev_handle: dev_handle: 0x0000000000000000, parent_handle: 0xffff880000f49d40 <7>pata_get_dev_handle: for dev=0x1f.2, addr=0x1f0002, parent=0xffff8800005ff800, *handle=0x0000000000000000 <6>ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x9088 irq 15 <6>ata2: SATA port has no device. <6>scsi1 : ata_piix <7>pata_get_dev_handle: ENTER: dev->bus_id='0000:00:1f.2' <7>pata_get_dev_handle: dev_handle: 0x0000000000000000, parent_handle: 0xffff880000f49d40 <7>pata_get_dev_handle: for dev=0x1f.2, addr=0x1f0002, parent=0xffff8800005ff800, *handle=0x0000000000000000 <6>Fusion MPT base driver 3.03.08 <6>Copyright (c) 1999-2005 LSI Logic Corporation <4>sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray <6>Uniform CD-ROM driver Revision: 3.20 <7>sr 0:0:0:0: Attached scsi CD-ROM sr0 <6>Fusion MPT SPI Host driver 3.03.08 <5>sr 0:0:0:0: Attached scsi generic sg0 type 5 <6>GSI 18 sharing vector 0xB0 and IRQ 18 <6>ACPI: PCI Interrupt 0000:14:05.0[A] -> GSI 72 (level, low) -> IRQ 18 <6>mptbase: Initiating ioc0 bringup <6>ioc0: 53C1030: Capabilities={Initiator,Target} <6>scsi2 : ioc0: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=18 <5> Vendor: SEAGATE Model: ST336753LC Rev: 0006 <5> Type: Direct-Access ANSI SCSI revision: 03 <6> target2:0:0: Beginning Domain Validation <6> target2:0:0: Ending Domain Validation <6> target2:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP (6.25 ns, offset 63) <5>SCSI device sda: 71687372 512-byte hdwr sectors (36704 MB) <5>sda: Write Protect is off <7>sda: Mode Sense: ab 00 10 08 <5>SCSI device sda: drive cache: write back w/ FUA <5>SCSI device sda: 71687372 512-byte hdwr sectors (36704 MB) <5>sda: Write Protect is off <7>sda: Mode Sense: ab 00 10 08 <5>SCSI device sda: drive cache: write back w/ FUA <6> sda: sda1 sda2 sda3 <5>sd 2:0:0:0: Attached scsi disk sda <5>sd 2:0:0:0: Attached scsi generic sg1 type 0 <5> Vendor: ESG-SHV Model: SCA HSBP M35 Rev: 1.06 <5> Type: Processor ANSI SCSI revision: 02 <6> target2:0:6: Beginning Domain Validation <6> target2:0:6: Ending Domain Validation <6> target2:0:6: asynchronous <5> 2:0:6:0: Attached scsi generic sg2 type 3 <6>GSI 19 sharing vector 0xB8 and IRQ 19 <6>ACPI: PCI Interrupt 0000:14:05.1[B] -> GSI 73 (level, low) -> IRQ 19 <6>mptbase: Initiating ioc1 bringup <6>ioc1: 53C1030: Capabilities={Initiator,Target} <6>scsi3 : ioc1: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=19 <5> Vendor: ESG-SHV Model: SCA HSBP M35 Rev: 1.06 <5> Type: Processor ANSI SCSI revision: 02 <6> target3:0:6: Beginning Domain Validation <6> target3:0:6: Ending Domain Validation <6> target3:0:6: asynchronous <5> 3:0:6:0: Attached scsi generic sg3 type 3 <5> Vendor: SEAGATE Model: ST336753LC Rev: 0006 <5> Type: Direct-Access ANSI SCSI revision: 03 <6> target3:0:10: Beginning Domain Validation <6> target3:0:10: Ending Domain Validation <6> target3:0:10: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP (6.25 ns, offset 63) <5>SCSI device sdb: 71687372 512-byte hdwr sectors (36704 MB) <5>sdb: Write Protect is off <7>sdb: Mode Sense: ab 00 10 08 <5>SCSI device sdb: drive cache: write back w/ FUA <5>SCSI device sdb: 71687372 512-byte hdwr sectors (36704 MB) <5>sdb: Write Protect is off <7>sdb: Mode Sense: ab 00 10 08 <5>SCSI device sdb: drive cache: write back w/ FUA <6> sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 > <5>sd 3:0:10:0: Attached scsi disk sdb <5>sd 3:0:10:0: Attached scsi generic sg4 type 0 <5>ReiserFS: sdb5: found reiserfs format "3.6" with standard journal <5>ReiserFS: sdb5: using ordered data mode <4>reiserfs: using flush barriers <5>ReiserFS: sdb5: journal params: device sdb5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>ReiserFS: sdb5: checking transaction log (sdb5) <5>ReiserFS: sdb5: Using r5 hash to sort names <5>ReiserFS: sdb5: Removing [260 97232 0x0 SD]..done <5>ReiserFS: sdb5: Removing [26625 96932 0x0 SD]..done <5>ReiserFS: sdb5: There were 2 uncompleted unlinks/truncates. Completed <6>Adding 2104476k swap on /dev/sda2. Priority:-1 extents:1 across:2104476k <6>Adding 1951856k swap on /dev/sdb1. Priority:-2 extents:1 across:1951856k <6>tg3.c:v3.49 (Feb 2, 2006) <6>GSI 20 sharing vector 0xC0 and IRQ 20 <6>ACPI: PCI Interrupt 0000:12:02.0[A] -> GSI 48 (level, low) -> IRQ 20 <6>eth0: Tigon3 [partno(BCM95704A6) rev 2100 PHY(5704)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0e:0c:42:a2:71 <6>eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0] <6>eth0: dma_rwctrl[769f4000] dma_mask[64-bit] <6>GSI 21 sharing vector 0xC8 and IRQ 21 <6>ACPI: PCI Interrupt 0000:12: 02.1[B] -> GSI 49 (level, low) -> IRQ 21 <6>eth1: Tigon3 [partno(BCM95704A6) rev 2100 PHY(5704)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0e:0c:42:a2:72 <6>eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] <6>eth1: dma_rwctrl[769f4000] dma_mask[64-bit] <3>i8xx TCO timer: failed to reset NO_REBOOT flag, reboot disabled by hardware <6>usbcore: registered new driver usbfs <6>usbcore: registered new driver hub <6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5 <6>shpchp: HPC vendor_id 8086 device_id 329 ss_vid 0 ss_did 0 <6>ACPI: PCI Interrupt 0000:0e:00.0[A] -> GSI 47 (level, low) -> IRQ 16 <6>shpchp: Can't get msi for the hotplug controller <6>shpchp: Use INTx for the hotplug controller <6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 <6>USB Universal Host Controller Interface driver v2.3 <6>GSI 22 sharing vector 0xD0 and IRQ 22 <6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 22 <7>PCI: Setting latency timer of device 0000:00:1d.0 to 64 <6>uhci_hcd 0000:00: 1d.0: UHCI Host Controller <6>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 <6>uhci_hcd 0000:00:1d.0: irq 22, io base 0x00009060 <6>usb usb1: new device found, idVendor=0000, idProduct=0000 <6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb1: Product: UHCI Host Controller <6>usb usb1: Manufacturer: Linux 2.6.16.11-7-xen uhci_hcd <6>usb usb1: SerialNumber: 0000:00: 1d.0 <6>usb usb1: configuration #1 chosen from 1 choice <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 2 ports detected <6>GSI 23 sharing vector 0xD8 and IRQ 23 <6>ACPI: PCI Interrupt 0000:00: 1d.1[B] -> GSI 19 (level, low) -> IRQ 23 <7>PCI: Setting latency timer of device 0000:00:1d.1 to 64 <6>uhci_hcd 0000:00:1d.1: UHCI Host Controller <6>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 <6>uhci_hcd 0000:00:1d.1: irq 23, io base 0x00009040 <6>usb usb2: new device found, idVendor=0000, idProduct=0000 <6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb2: Product: UHCI Host Controller <6>usb usb2: Manufacturer: Linux 2.6.16.11-7-xen uhci_hcd <6>usb usb2: SerialNumber: 0000:00:1d.1 <6>usb usb2: configuration #1 chosen from 1 choice <6>hub 2-0:1.0: USB hub found <6>hub 2-0: 1.0: 2 ports detected <6>ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17 <7>PCI: Setting latency timer of device 0000:00:1d.2 to 64 <6>uhci_hcd 0000:00:1d.2: UHCI Host Controller <6>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 <6>uhci_hcd 0000:00:1d.2: irq 17, io base 0x00009020 <6>usb usb3: new device found, idVendor=0000, idProduct=0000 <6>usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb3: Product: UHCI Host Controller <6>usb usb3: Manufacturer: Linux 2.6.16.11-7-xen uhci_hcd <6>usb usb3: SerialNumber: 0000:00:1d.2 <6>usb usb3: configuration #1 chosen from 1 choice <6>hub 3-0:1.0: USB hub found <6>hub 3-0:1.0: 2 ports detected <6>GSI 24 sharing vector 0x21 and IRQ 24 <6>ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 24 <7>PCI: Setting latency timer of device 0000:00:1d.7 to 64 <6>ehci_hcd 0000:00:1d.7: EHCI Host Controller <6>ehci_hcd 0000:00:1d.7: debug port 1 <7>PCI: cache line size of 128 is not supported by device 0000:00: 1d.7 <6>ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 <6>ehci_hcd 0000:00:1d.7: irq 24, io mem 0xb8300000 <6>ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 <6>usb usb4: new device found, idVendor=0000, idProduct=0000 <6>usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb4: Product: EHCI Host Controller <6>usb usb4: Manufacturer: Linux 2.6.16.11-7-xen ehci_hcd <6>usb usb4: SerialNumber: 0000:00:1d.7 <6>usb usb4: configuration #1 chosen from 1 choice <6>hub 4-0:1.0: USB hub found <6>hub 4-0:1.0: 6 ports detected <3>hw_random: RNG not detected <6>usb 4-3: new high speed USB device using ehci_hcd and address 2 <6>usb 4-3: new device found, idVendor=0424, idProduct=a700 <6>usb 4-3: new device strings: Mfr=0, Product=0, SerialNumber=0 <6>usb 4-3: configuration #1 chosen from 1 choice <6>hub 4-3:1.0: USB hub found <6>hub 4-3:1.0: 3 ports detected <6>usb 3-1: new low speed USB device using uhci_hcd and address 2 <6>device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@xxxxxxxxxx <7>dm-netlink version 0.0.2 loaded <6>usb 3-1: new device found, idVendor=046d, idProduct=c00e <6>usb 3-1: new device strings: Mfr=1, Product=2, SerialNumber=0 <6>usb 3-1: Product: USB-PS/2 Optical Mouse <6>usb 3-1: Manufacturer: Logitech <6>usb 3-1: configuration #1 chosen from 1 choice <6>usb 3-2: new low speed USB device using uhci_hcd and address 3 <6>usb 3-2: new device found, idVendor=05a4, idProduct=9841 <6>usb 3-2: new device strings: Mfr=0, Product=1, SerialNumber=0 <6>usb 3-2: Product: USB Compliant Keyboard <6>usb 3-2: configuration #1 chosen from 1 choice <6>usbcore: registered new driver hiddev <6>input: Logitech USB-PS/2 Optical Mouse as /class/input/input1 <6>input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1 <6>input: USB Compliant Keyboard as /class/input/input2 <6>input: USB HID v1.10 Keyboard [USB Compliant Keyboard] on usb-0000:00:1d.2-2 <6>input: USB Compliant Keyboard as /class/input/input3 <6>input: USB HID v1.10 Device [USB Compliant Keyboard] on usb-0000:00:1d.2-2 <6>usbcore: registered new driver usbhid <6>drivers/usb/input/hid-core.c: v2.6:USB HID core driver <6>loop: loaded (max 8 devices) <6>AppArmor: AppArmor (version 2.0-19.43r6320) initialized <5>audit(1146758892.917:2): AppArmor (version 2.0-19.43r6320) initialized <4> Kernel logging (ksyslog) stopped. Kernel log daemon terminating. Boot logging started on /dev/tty1(/dev/console (deleted)) at Thu May 4 12:08:07 2006 <notice>startproc: execve (/sbin/udevd) [ /sbin/udevd --daemon ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION= sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/bin vga=0x31a DO_CONFIRM= RUNLEVEL=S PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/sbin/udevd ] Activating swap-devices in /etc/fstab... doneStarting udevd done Loading required kernel modules doneActivating device mapper... done Starting MD Raid done Waiting for udev to settle... Scanning for LVM volume groups... Reading all physical volumes. This may take a while... No volume groups found No volume groups found Activating LVM volume groups... No volume groups found done Checking file systems... fsck 1.38 (30-Jun-2005) donedone Mounting local file systems... proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) debugfs on /sys/kernel/debug type debugfs (rw) udev on /dev type tmpfs (rw) devpts on /dev/pts type devpts (rw,mode=0620,gid=5) nothing was mounted donedone Cleaning up using /sbin/modify_resolvconf: restored /etc/resolv.conf from /etc/resolv.conf.saved.by.dhcpcd.eth0 done Loading AppArmor module done Mounting securityfs on /sys/kernel/security done Loading AppArmor profiles done Setting up hostname 'bombe64'done Setting up loopback interface lo lo IP address: 127.0.0.1/8 done Setting up the hardware clockdone Creating /var/log/boot.msg done<notice>killproc: kill(1573,29) Activating remaining swap-devices in /etc/fstab... doneSetting current sysctl status from /etc/sysctl.conf net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.rp_filter = 1 done Enabling syn flood protectiondone Disabling IP forwardingdone done System Boot Control: The system has been set up Skipped features: boot.cycle System Boot Control: Running /etc/init.d/boot.local done<notice>killproc: kill(1573,3) INIT: Entering runlevel: 5 Boot logging started on /dev/tty1(/dev/console) at Thu May 4 12:08:14 2006 Master Resource Control: previous runlevel: N, switching to runlevel: 5 ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin<notice>startproc: execve (/usr/bin/dbus-daemon) [ /usr/bin/dbus-daemon --system vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/usr/bin/dbus-daemon ] <notice>startproc: execve (/usr/sbin/irqbalance) [ /usr/sbin/irqbalance ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/usr/sbin/irqbalance ] Loading AppArmor profiles - AppArmor already loaded with profiles. Not loading profiles. warning Starting D-BUS daemondone Initializing random number generatordone <notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION= sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/sbin/resmgrd ] Starting irqbalance done Starting resource managerdone <notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION= sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 SPLASHCFG= resume=/dev/sda2 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 SPLASH=no splash=silent ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/sbin/syslog-ng ] <notice>startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/sbin/acpid ] <notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 SPLASHCFG= resume=/dev/sda2 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 SPLASH=no splash=silent ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/sbin/klogd ] Starting syslog servicesdone acpid: loading ACPI modules ( ac battery button ) done Starting acpid done <notice>startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes --retain-privileges ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION= sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/usr/sbin/hald ] Starting HAL daemondone Loading keymap i386/qwerty/us.map.gz doneLoading compose table winkeys shiftctrl latin1.adddone Start Unicode mode doneLoading console font lat9w-16.psfu -m trivial G0:loadable doneSetting up network interfaces: lo lo IP address: 127.0.0.1/8 done eth0 device: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10) eth0 configuration: eth-id-00:0e:0c:42:a2:71 eth0 (DHCP) . . . . . <notice>pidofproc: dhcpcd 4287 IP/Netmask: 192.168.1.147 / 255.255.255.0 ('bombe64') done eth1 device: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10) No configuration found for eth1 unusedSetting up service network . . . . . . . . . . . . . . . .done <notice>startproc: execve (/sbin/auditd) [ /sbin/auditd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION= sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/sbin/auditd ] Starting ZENworks Management Daemondone <notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION= sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/sbin/portmap ] <notice>startproc: execve (/usr/sbin/slpd) [ /usr/sbin/slpd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/usr/sbin/slpd ] Starting RPC portmap daemondone Starting slpd done Starting auditd done Importing Net File System (NFS)unused Mount SMB/ CIFS File Systems unused Starting nfsboot (sm-notify) done <notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION= sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/usr/sbin/nscd ] <notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/usr/sbin/sshd ] <notice>startproc: execve (/usr/sbin/xinetd) [ /usr/sbin/xinetd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/usr/sbin/xinetd ] Starting Name Service Cache Daemondone Starting SSH daemondone Checking/updating CPU microcode done Starting INET services. (xinetd)done <notice>startproc: execve (/opt/gnome/sbin/gdm) [ /opt/gnome/sbin/gdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 INIT_VERSION= sysvinit-2.86 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= LANG=en_US.UTF-8 PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ XCURSOR_THEME=Industrial WINDOWMANAGER=/usr/X11R6/bin/gnome splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/opt/gnome/sbin/gdm ] Starting service gdmdone <notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/usr/bin:/sbin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ] Starting powersaved: done Starting mail service (Postfix)done <notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION= sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/usr/bin:/sbin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ resume=/dev/sda2 SPLASHCFG= PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/sdb5 _=/sbin/startproc DAEMON=/usr/sbin/cron ] Starting CRON daemondone Starting xend <notice>checkproc: /opt/gnome/sbin/gdm 5112 <notice>checkproc: /sbin/dhcpcd 4433 <notice>checkproc: /sbin/dhcpcd 4433 <notice>pidofproc: dhcpcd 6530 done Starting xendomainsunused Master Resource Control: runlevel 5 has been reached Skipped services in runlevel 5: smbfs nfs splash xendomains <notice>killproc: kill(3696,3) ====================================== -- Rene Jr Purcell 418 930-2424 _______________________________________________ Xen-users mailing list Xen-users@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-users
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |