|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [PATCH v4 1/4] xen/char: add classic i.MX UART driver
Add a console driver for the classic i.MX UART IP ("fsl,imx6q-uart"
compatible), used as the console UART on the i.MX8M family. Baudrate
and pin configuration are inherited from the bootloader; the driver
only enables the transmitter/receiver and wires up the RX/TX
interrupts, mirroring the existing imx-lpuart driver.
The i.MX8M family's UART IP differs from the LPUART used on
i.MX8QM/8QXP, so a separate driver is needed.
Signed-off-by: Wig Cheng <onlywig@xxxxxxxxx>
Reviewed-by: Michal Orzel <michal.orzel@xxxxxxx>
---
Changes in v4:
- No code changes; picked up Michal's Reviewed-by.
MAINTAINERS | 1 +
xen/arch/arm/include/asm/imx-uart.h | 57 +++++++
xen/drivers/char/Kconfig | 8 +
xen/drivers/char/Makefile | 1 +
xen/drivers/char/imx-uart.c | 233 ++++++++++++++++++++++++++++
5 files changed, 300 insertions(+)
create mode 100644 xen/arch/arm/include/asm/imx-uart.h
create mode 100644 xen/drivers/char/imx-uart.c
diff --git a/MAINTAINERS b/MAINTAINERS
index ed0ffa608f..4dd97ffcad 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -269,6 +269,7 @@ F: xen/arch/arm/
F: xen/drivers/char/cadence-uart.c
F: xen/drivers/char/exynos4210-uart.c
F: xen/drivers/char/imx-lpuart.c
+F: xen/drivers/char/imx-uart.c
F: xen/drivers/char/meson-uart.c
F: xen/drivers/char/mvebu-uart.c
F: xen/drivers/char/omap-uart.c
diff --git a/xen/arch/arm/include/asm/imx-uart.h
b/xen/arch/arm/include/asm/imx-uart.h
new file mode 100644
index 0000000000..a3892020e6
--- /dev/null
+++ b/xen/arch/arm/include/asm/imx-uart.h
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Register definitions for the classic i.MX UART IP
+ * ("fsl,imx6q-uart" compatible), used as the console UART on the
+ * i.MX8M family.
+ *
+ * Register layout taken from Linux drivers/tty/serial/imx.c.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#ifndef ASM_IMX_UART_H
+#define ASM_IMX_UART_H
+
+#include <xen/const.h>
+
+#define URXD0 0x00 /* Receiver Register */
+#define URTX0 0x40 /* Transmitter Register */
+#define UCR1 0x80 /* Control Register 1 */
+#define UCR2 0x84 /* Control Register 2 */
+#define USR1 0x94 /* Status Register 1 */
+#define USR2 0x98 /* Status Register 2 */
+#define UTS 0xb4 /* Test Register */
+
+#define URXD_RX_DATA 0xff
+
+#define UCR1_UARTEN BIT(0, U) /* UART enable */
+#define UCR1_ATDMAEN BIT(2, U) /* Aging DMA timer enable */
+#define UCR1_TXDMAEN BIT(3, U) /* Transmitter ready DMA enable */
+#define UCR1_TXMPTYEN BIT(6, U) /* Transmitter empty interrupt enable */
+#define UCR1_RXDMAEN BIT(8, U) /* Receiver ready DMA enable */
+#define UCR1_RRDYEN BIT(9, U) /* Receiver ready interrupt enable */
+#define UCR1_TRDYEN BIT(13, U) /* Transmitter ready interrupt enable */
+
+#define UCR2_SRST BIT(0, U) /* 0 = issue software reset */
+#define UCR2_RXEN BIT(1, U) /* Receiver enable */
+#define UCR2_TXEN BIT(2, U) /* Transmitter enable */
+
+#define USR1_TRDY BIT(13, U) /* Transmitter ready */
+
+#define USR2_RDR BIT(0, U) /* Receive data ready */
+#define USR2_ORE BIT(1, U) /* Overrun error */
+
+#define UTS_TXFULL BIT(4, U) /* TX FIFO full */
+#define UTS_RXEMPTY BIT(5, U) /* RX FIFO empty */
+#define UTS_TXEMPTY BIT(6, U) /* TX FIFO empty */
+
+#endif /* ASM_IMX_UART_H */
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */
diff --git a/xen/drivers/char/Kconfig b/xen/drivers/char/Kconfig
index 8e49a52c73..f237c0220d 100644
--- a/xen/drivers/char/Kconfig
+++ b/xen/drivers/char/Kconfig
@@ -30,6 +30,14 @@ config HAS_IMX_LPUART
help
This selects the i.MX LPUART. If you have i.MX8QM based board, say Y.
+config HAS_IMX_UART
+ bool "i.MX UART driver"
+ default y
+ depends on ARM_64
+ help
+ This selects the classic i.MX UART. If you have an i.MX8M family
+ based board, say Y.
+
config HAS_MVEBU
bool "Marvell MVEBU UART driver"
default y
diff --git a/xen/drivers/char/Makefile b/xen/drivers/char/Makefile
index 8cbbffdca8..039f566926 100644
--- a/xen/drivers/char/Makefile
+++ b/xen/drivers/char/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_HAS_SCIF) += scif-uart.o
obj-$(CONFIG_HAS_EHCI) += ehci-dbgp.o
obj-$(CONFIG_XHCI) += xhci-dbc.o
obj-$(CONFIG_HAS_IMX_LPUART) += imx-lpuart.o
+obj-$(CONFIG_HAS_IMX_UART) += imx-uart.o
obj-$(CONFIG_HAS_LINFLEX) += linflex-uart.o
obj-$(CONFIG_GENERIC_UART_INIT) += uart-init.o
obj-y += serial.o
diff --git a/xen/drivers/char/imx-uart.c b/xen/drivers/char/imx-uart.c
new file mode 100644
index 0000000000..2dc531a84e
--- /dev/null
+++ b/xen/drivers/char/imx-uart.c
@@ -0,0 +1,233 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Driver for the classic i.MX UART IP ("fsl,imx6q-uart"), used as the
+ * console UART on the i.MX8M family (e.g. i.MX8MP).
+ *
+ * Baudrate and pin configuration are inherited from the bootloader.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#include <xen/errno.h>
+#include <xen/init.h>
+#include <xen/irq.h>
+#include <xen/mm.h>
+#include <xen/serial.h>
+#include <asm/device.h>
+#include <asm/imx-uart.h>
+#include <asm/io.h>
+
+#define imx_uart_read(uart, off) readl((uart)->regs + (off))
+#define imx_uart_write(uart, off, val) writel((val), (uart)->regs + (off))
+
+static struct imx_uart {
+ uint32_t irq;
+ char __iomem *regs;
+ struct irqaction irqaction;
+ struct vuart_info vuart;
+} imx8m_com;
+
+static void imx_uart_interrupt(int irq, void *data)
+{
+ struct serial_port *port = data;
+ struct imx_uart *uart = port->uart;
+
+ if ( imx_uart_read(uart, USR2) & USR2_RDR )
+ serial_rx_interrupt(port);
+
+ /*
+ * USR1_TRDY is a raw status bit, set whenever the transmitter has
+ * room regardless of whether the TX interrupt is enabled. Only treat
+ * it as a TX interrupt when TRDYEN is set, otherwise an RX-only
+ * interrupt would spuriously enter serial_tx_interrupt().
+ */
+ if ( (imx_uart_read(uart, USR1) & USR1_TRDY) &&
+ (imx_uart_read(uart, UCR1) & UCR1_TRDYEN) )
+ serial_tx_interrupt(port);
+}
+
+static void __init imx_uart_init_preirq(struct serial_port *port)
+{
+ struct imx_uart *uart = port->uart;
+ uint32_t ucr1, ucr2;
+
+ /*
+ * Reuse the bootloader settings; only enable the UART and both
+ * directions. The console uses UCR1 interrupts (RRDYEN/TRDYEN)
+ * exclusively, so just clear UCR1's interrupt and DMA enables.
+ */
+ ucr1 = imx_uart_read(uart, UCR1);
+ ucr1 &= ~(UCR1_RRDYEN | UCR1_TRDYEN | UCR1_TXMPTYEN | UCR1_RXDMAEN |
+ UCR1_TXDMAEN | UCR1_ATDMAEN);
+ ucr1 |= UCR1_UARTEN;
+ imx_uart_write(uart, UCR1, ucr1);
+
+ ucr2 = imx_uart_read(uart, UCR2);
+ ucr2 |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN;
+ imx_uart_write(uart, UCR2, ucr2);
+}
+
+static void __init imx_uart_init_postirq(struct serial_port *port)
+{
+ struct imx_uart *uart = port->uart;
+ uint32_t ucr1;
+
+ uart->irqaction.handler = imx_uart_interrupt;
+ uart->irqaction.name = "imx_uart";
+ uart->irqaction.dev_id = port;
+
+ if ( setup_irq(uart->irq, 0, &uart->irqaction) != 0 )
+ {
+ dprintk(XENLOG_ERR, "Failed to allocate imx_uart IRQ %u\n", uart->irq);
+ return;
+ }
+
+ /* Enable the receiver ready interrupt */
+ ucr1 = imx_uart_read(uart, UCR1);
+ ucr1 |= UCR1_RRDYEN;
+ imx_uart_write(uart, UCR1, ucr1);
+}
+
+static int imx_uart_tx_ready(struct serial_port *port)
+{
+ struct imx_uart *uart = port->uart;
+
+ return !(imx_uart_read(uart, UTS) & UTS_TXFULL);
+}
+
+static void imx_uart_putc(struct serial_port *port, char c)
+{
+ struct imx_uart *uart = port->uart;
+
+ while ( imx_uart_read(uart, UTS) & UTS_TXFULL )
+ cpu_relax();
+
+ imx_uart_write(uart, URTX0, c);
+}
+
+static int imx_uart_getc(struct serial_port *port, char *pc)
+{
+ struct imx_uart *uart = port->uart;
+
+ if ( !(imx_uart_read(uart, USR2) & USR2_RDR) )
+ return 0;
+
+ *pc = imx_uart_read(uart, URXD0) & URXD_RX_DATA;
+
+ if ( imx_uart_read(uart, USR2) & USR2_ORE )
+ imx_uart_write(uart, USR2, USR2_ORE);
+
+ return 1;
+}
+
+static int __init imx_uart_irq(struct serial_port *port)
+{
+ struct imx_uart *uart = port->uart;
+
+ return ((uart->irq > 0) ? uart->irq : -1);
+}
+
+static const struct vuart_info *imx_uart_vuart_info(struct serial_port *port)
+{
+ struct imx_uart *uart = port->uart;
+
+ return &uart->vuart;
+}
+
+static void imx_uart_start_tx(struct serial_port *port)
+{
+ struct imx_uart *uart = port->uart;
+ uint32_t ucr1;
+
+ ucr1 = imx_uart_read(uart, UCR1);
+ imx_uart_write(uart, UCR1, ucr1 | UCR1_TRDYEN);
+}
+
+static void imx_uart_stop_tx(struct serial_port *port)
+{
+ struct imx_uart *uart = port->uart;
+ uint32_t ucr1;
+
+ ucr1 = imx_uart_read(uart, UCR1);
+ imx_uart_write(uart, UCR1, ucr1 & ~UCR1_TRDYEN);
+}
+
+static struct uart_driver __read_mostly imx_uart_driver = {
+ .init_preirq = imx_uart_init_preirq,
+ .init_postirq = imx_uart_init_postirq,
+ .tx_ready = imx_uart_tx_ready,
+ .putc = imx_uart_putc,
+ .getc = imx_uart_getc,
+ .irq = imx_uart_irq,
+ .start_tx = imx_uart_start_tx,
+ .stop_tx = imx_uart_stop_tx,
+ .vuart_info = imx_uart_vuart_info,
+};
+
+static int __init imx_uart_init(struct dt_device_node *dev, const void *data)
+{
+ const char *config = data;
+ struct imx_uart *uart;
+ int res;
+ paddr_t addr, size;
+
+ if ( strcmp(config, "") )
+ printk("WARNING: UART configuration is not supported\n");
+
+ uart = &imx8m_com;
+
+ res = dt_device_get_paddr(dev, 0, &addr, &size);
+ if ( res )
+ {
+ printk("imx-uart: Unable to retrieve the base address of the UART\n");
+ return res;
+ }
+
+ res = platform_get_irq(dev, 0);
+ if ( res < 0 )
+ {
+ printk("imx-uart: Unable to retrieve the IRQ\n");
+ return -EINVAL;
+ }
+ uart->irq = res;
+
+ uart->regs = ioremap_nocache(addr, size);
+ if ( !uart->regs )
+ {
+ printk("imx-uart: Unable to map the UART memory\n");
+ return -ENOMEM;
+ }
+
+ uart->vuart.base_addr = addr;
+ uart->vuart.size = size;
+ uart->vuart.data_off = URTX0;
+ uart->vuart.status_off = UTS;
+ uart->vuart.status = UTS_TXEMPTY | UTS_RXEMPTY;
+
+ /* Register with generic serial driver */
+ serial_register_uart(SERHND_DTUART, &imx_uart_driver, uart);
+
+ dt_device_set_used_by(dev, DOMID_XEN);
+
+ return 0;
+}
+
+static const struct dt_device_match imx_uart_dt_compat[] __initconst =
+{
+ DT_MATCH_COMPATIBLE("fsl,imx6q-uart"),
+ { /* sentinel */ },
+};
+
+DT_DEVICE_START(imx_uart, "i.MX UART", DEVICE_SERIAL)
+ .dt_match = imx_uart_dt_compat,
+ .init = imx_uart_init,
+DT_DEVICE_END
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */
--
2.43.0
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |