[Xen-devel] [PATCH 17/17] xen/arm64: Zero BSS after the MMU and D-cache is turned on

[Julien Grall <julien.grall@xxxxxxx>]

At the moment BSS is zeroed before the MMU and D-Cache is turned on.
In other words, the cache will be bypassed when zeroing the BSS section.

Per the Image protocol [1], the state of the cache for BSS region is not
known because it is not part of the "loaded kernel image".

This means that the cache will need to be invalidated twice for the BSS
region:
    1) Before zeroing to remove any dirty cache line. Otherwise they may
    get evicted while zeroing and therefore overriding the value.
    2) After zeroing to remove any cache line that may have been
    speculated. Otherwise when turning on MMU and D-Cache, the CPU may
    see old values.

However, the only reason to have the BSS zeroed early is because the
boot page tables are part of BSS. To avoid the two cache invalidations,
it is possible to move the page tables in the section .data.page_aligned.

A new macro DEFINE_BOOT_PAGE_TABLE is introduced to create and mark
page-tables used before BSS is zeroed. This includes all boot_* but also
xen_fixmap as zero_bss() will print a message when earlyprintk is
enabled.

[1] linux/Documentation/arm64/booting.txt

---

    Note that the arm32 support is not there yet. This will need to be
    addressed here or separately depending on when the Arm32 boot rework
    is sent.
---
 xen/arch/arm/arm64/head.S |  6 +++---
 xen/arch/arm/mm.c         | 23 +++++++++++++++++------
 2 files changed, 20 insertions(+), 9 deletions(-)

diff --git a/xen/arch/arm/arm64/head.S b/xen/arch/arm/arm64/head.S
index 130ab66d8e..6c3edbbc81 100644
--- a/xen/arch/arm/arm64/head.S
+++ b/xen/arch/arm/arm64/head.S
@@ -291,7 +291,6 @@ real_start_efi:
         mov   x22, #0                /* x22 := is_secondary_cpu */
 
         bl    check_cpu_mode
-        bl    zero_bss
         bl    cpu_init
         bl    create_page_tables
         bl    enable_mmu
@@ -312,6 +311,7 @@ primary_switched:
         /* Use a virtual address to access the UART. */
         ldr   x23, =EARLY_UART_VIRTUAL_ADDRESS
 #endif
+        bl    zero_bss
         PRINT("- Ready -\r\n")
         /* Setup the arguments for start_xen and jump to C world */
         mov   x0, x20                /* x0 := phys_offset */
@@ -423,8 +423,8 @@ zero_bss:
         cbnz  x26, skip_bss
 
         PRINT("- Zero BSS -\r\n")
-        load_paddr x0, __bss_start    /* Load paddr of start & end of bss */
-        load_paddr x1, __bss_end
+        ldr   x0, =__bss_start       /* x0 := vaddr(__bss_start) */
+        ldr   x1, =__bss_end         /* x1 := vaddr(__bss_start) */
 
 1:      str   xzr, [x0], #8
         cmp   x0, x1
diff --git a/xen/arch/arm/mm.c b/xen/arch/arm/mm.c
index 6a549e9283..0b2d07a258 100644
--- a/xen/arch/arm/mm.c
+++ b/xen/arch/arm/mm.c
@@ -48,6 +48,17 @@
 #undef mfn_to_virt
 #define mfn_to_virt(mfn) __mfn_to_virt(mfn_x(mfn))
 
+/*
+ * Macros to define page-tables:
+ *  - DEFINE_BOOT_PAGE_TABLE is used to define page-table that are used
+ *  in assembly code before BSS is zeroed.
+ *  - DEFINE_PAGE_TABLE{,S} are used to define one or multiple
+ *  page-tables to be used after BSS is zeroed (typically they are only used
+ *  in C).
+ */
+#define DEFINE_BOOT_PAGE_TABLE(name)                                          \
+lpae_t __aligned(PAGE_SIZE) __section(".data.page_aligned") name[LPAE_ENTRIES]
+
 #define DEFINE_PAGE_TABLES(name, nr)                    \
 lpae_t __aligned(PAGE_SIZE) name[LPAE_ENTRIES * (nr)]
 
@@ -76,13 +87,13 @@ lpae_t __aligned(PAGE_SIZE) name[LPAE_ENTRIES * (nr)]
  * Finally, if EARLY_PRINTK is enabled then xen_fixmap will be mapped
  * by the CPU once it has moved off the 1:1 mapping.
  */
-DEFINE_PAGE_TABLE(boot_pgtable);
+DEFINE_BOOT_PAGE_TABLE(boot_pgtable);
 #ifdef CONFIG_ARM_64
-DEFINE_PAGE_TABLE(boot_first);
-DEFINE_PAGE_TABLE(boot_first_id);
+DEFINE_BOOT_PAGE_TABLE(boot_first);
+DEFINE_BOOT_PAGE_TABLE(boot_first_id);
 #endif
-DEFINE_PAGE_TABLE(boot_second);
-DEFINE_PAGE_TABLE(boot_third);
+DEFINE_BOOT_PAGE_TABLE(boot_second);
+DEFINE_BOOT_PAGE_TABLE(boot_third);
 
 /* Main runtime page tables */
 
@@ -135,7 +146,7 @@ static __initdata int xenheap_first_first_slot = -1;
  */
 static DEFINE_PAGE_TABLES(xen_second, 2);
 /* First level page table used for fixmap */
-DEFINE_PAGE_TABLE(xen_fixmap);
+DEFINE_BOOT_PAGE_TABLE(xen_fixmap);
 /* First level page table used to map Xen itself with the XN bit set
  * as appropriate. */
 static DEFINE_PAGE_TABLE(xen_xenmap);
-- 
2.11.0


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel