[Xen-devel] [PATCH 06/17] xen/arm64: head: Introduce distinct paths for the boot CPU and secondary CPUs

[Julien Grall <julien.grall@xxxxxxx>]

The boot code is currently quite difficult to go through because of the
lack of documentation and a number of indirection to avoid executing
some path in either the boot CPU or secondary CPUs.

In an attempt to make the boot code easier to follow, each parts of the
boot are now in separate functions. Furthermore, the paths for the boot
CPU and secondary CPUs are now distincted and for now will call each
functions.

Follow-ups will remove unecessary calls and do further improvement
(such as adding documentation and reshuffling).

Note that the switch from using the ID mapping to the runtime mapping
is duplicated for each path. This is because in the future we will need
to stay longer in the ID mapping for the boot CPU.

Signed-off-by: Julien Grall <julien.grall@xxxxxxx>
---
 xen/arch/arm/arm64/head.S | 57 ++++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 49 insertions(+), 8 deletions(-)

diff --git a/xen/arch/arm/arm64/head.S b/xen/arch/arm/arm64/head.S
index 9142b4a774..ccd8a1b0a8 100644
--- a/xen/arch/arm/arm64/head.S
+++ b/xen/arch/arm/arm64/head.S
@@ -290,7 +290,19 @@ real_start_efi:
 
         mov   x22, #0                /* x22 := is_secondary_cpu */
 
-        b     common_start
+        bl    check_cpu_mode
+        bl    zero_bss
+        bl    cpu_init
+        bl    create_page_tables
+        bl    enable_mmu
+
+        /* We are still in the ID map. Jump to the runtime Virtual Address. */
+        ldr   x0, =primary_switched
+        br    x0
+primary_switched:
+        bl    setup_fixmap
+        b     launch
+ENDPROC(real_start)
 
 GLOBAL(init_secondary)
         msr   DAIFSet, 0xf           /* Disable all interrupts */
@@ -324,9 +336,21 @@ GLOBAL(init_secondary)
         print_reg x24
         PRINT(" booting -\r\n")
 #endif
-
-common_start:
-
+        bl    check_cpu_mode
+        bl    zero_bss
+        bl    cpu_init
+        bl    create_page_tables
+        bl    enable_mmu
+
+        /* We are still in the ID map. Jump to the runtime Virtual Address. */
+        ldr   x0, =secondary_switched
+        br    x0
+secondary_switched:
+        bl    setup_fixmap
+        b     launch
+ENDPROC(init_secondary)
+
+check_cpu_mode:
         PRINT("- Current EL ")
         mrs   x5, CurrentEL
         print_reg x5
@@ -343,7 +367,10 @@ common_start:
         b fail
 
 el2:    PRINT("- Xen starting at EL2 -\r\n")
+        ret
+ENDPROC(check_cpu_mode)
 
+zero_bss:
         /* Zero BSS only when requested */
         cbnz  x26, skip_bss
 
@@ -356,6 +383,10 @@ el2:    PRINT("- Xen starting at EL2 -\r\n")
         b.lo  1b
 
 skip_bss:
+        ret
+ENDPROC(zero_bss)
+
+cpu_init:
         PRINT("- Setting up control registers -\r\n")
 
         /* Set up memory attribute type tables */
@@ -390,7 +421,10 @@ skip_bss:
          * are handled using the EL2 stack pointer, rather
          * than SP_EL0. */
         msr spsel, #1
+        ret
+ENDPROC(cpu_init)
 
+create_page_tables:
         /* Rebuild the boot pagetable's first-level entries. The structure
          * is described in mm.c.
          *
@@ -515,6 +549,10 @@ virtphys_clash:
         b     fail
 
 1:
+        ret
+ENDPROC(create_page_tables)
+
+enable_mmu:
         PRINT("- Turning on paging -\r\n")
 
         /*
@@ -524,16 +562,16 @@ virtphys_clash:
         tlbi  alle2                  /* Flush hypervisor TLBs */
         dsb   nsh
 
-        ldr   x1, =paging            /* Explicit vaddr, not RIP-relative */
         mrs   x0, SCTLR_EL2
         orr   x0, x0, #SCTLR_Axx_ELx_M  /* Enable MMU */
         orr   x0, x0, #SCTLR_Axx_ELx_C  /* Enable D-cache */
         dsb   sy                     /* Flush PTE writes and finish reads */
         msr   SCTLR_EL2, x0          /* now paging is enabled */
         isb                          /* Now, flush the icache */
-        br    x1                     /* Get a proper vaddr into PC */
-paging:
+        ret
+ENDPROC(enable_mmu)
 
+setup_fixmap:
         /* Now we can install the fixmap and dtb mappings, since we
          * don't need the 1:1 map any more */
         dsb   sy
@@ -575,7 +613,10 @@ paging:
         tlbi  alle2
         dsb   sy                     /* Ensure completion of TLB flush */
         isb
+        ret
+ENDPROC(setup_fixmap)
 
+launch:
         PRINT("- Ready -\r\n")
 
         /* The boot CPU should go straight into C now */
@@ -594,7 +635,6 @@ paging:
         dsb   sy                     /* Ensure completion of TLB flush */
         isb
 
-launch:
         ldr   x0, =init_data
         add   x0, x0, #INITINFO_stack /* Find the boot-time stack */
         ldr   x0, [x0]
@@ -609,6 +649,7 @@ launch:
         b     start_xen              /* and disappear into the land of C */
 1:
         b     start_secondary        /* (to the appropriate entry point) */
+ENDPROC(launch)
 
 /* Fail-stop */
 fail:   PRINT("- Boot failed -\r\n")
-- 
2.11.0


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel