Re: [Xen-devel] [ARM] gvirt_to_maddr fails when DomU is created

[Julien Grall <julien.grall@xxxxxxx>]

(+ Stefano)

On 11/27/18 5:12 PM, Volodymyr Babchuk wrote:
> Hello community,
Hi Volodymyr,

> After creating domU, I'm seeing lots of this messages from hypervisor:
>
> (XEN) p2m.c:1442: d1v0: gvirt_to_maddr failed va=0xffff80000efc7f0f
> flags=0x1 par=0x809
> (XEN) p2m.c:1442: d1v0: gvirt_to_maddr failed va=0xffff80000efc7f00
> flags=0x1 par=0x809
> (XEN) p2m.c:1442: d1v0: gvirt_to_maddr failed va=0xffff80000efc7f0f
> flags=0x1 par=0x809
>
> Interestingly, I'm getting them from both Dom0 and DomU:
>
> (XEN) p2m.c:1442: d0v0: gvirt_to_maddr failed va=0xffff80003efd7f0f
> flags=0x1 par=0x809
> (XEN) p2m.c:1442: d1v0: gvirt_to_maddr failed va=0xffff80000efc7f0f
> flags=0x1 par=0x809
>
> But only after DomU is created.
>
> I attached GDB and found that this is caused by update_runstate_area:
>
> (gdb) bt
> #0  get_page_from_gva (v=0x80005dbe2000, v@entry=0x22f2c8 <schedule+1236>,
>      va=va@entry=18446603337277996815, flags=flags@entry=1) at p2m.c:1440
> #1  0x000000000024e320 in translate_get_page (write=true, linear=true,
> addr=18446603337277996815,
>      info=...) at guestcopy.c:37
> #2  copy_guest (buf=buf@entry=0x80005dbe20d7,
> addr=addr@entry=18446603337277996815, len=len@entry=1,
>      info=..., flags=flags@entry=6) at guestcopy.c:69
> #3  0x000000000024e45c in raw_copy_to_guest (to=to@entry=0xffff80003efd7f0f,
>      from=from@entry=0x80005dbe20d7, len=len@entry=1) at guestcopy.c:110
> #4  0x00000000002497b4 in update_runstate_area
> (v=v@entry=0x80005dbe2000) at domain.c:287
> #5  0x0000000000249eb8 in context_switch (prev=prev@entry=0x80005dbe2000,
>      next=next@entry=0x80005bf3c000) at domain.c:344
> #6  0x000000000022f2c8 in schedule () at schedule.c:1583
> #7  0x0000000000232c10 in __do_softirq
> (ignore_mask=ignore_mask@entry=0) at softirq.c:50
> #8  0x0000000000232ca4 in do_softirq () at softirq.c:64
> #9  0x0000000000258254 in leave_hypervisor_tail () at traps.c:2302
>
> This issue is encountered on QEMU-ARMv8. Dom0 kernel is Linux 4.19.0
> My XEN master is at d8ffac1f7 "xen/arm: gic: Remove duplicated comment
> in do_sgi"
>
> The same setup worked perfectly with Xen 4.10.2
The message is only printed in debug build. Do you have CONFIG_DEBUG 
enabled?
> Julien, I saw on mailing list, that you paid attention to issues with
> gvirt_to_maddr,
> so maybe you can be interested in this.
Which thread are you speaking about? The problem is not because of 
gvirt_to_maddr but of how update_runstate_area is working at the moment.
update_runstate_area is using a guest virtual address to update the vCPU 
runstate. It blindly assumes the vCPU runstate will always be mapped in 
stage-1 page-tables. However, if KPTI (Kernel Page Table Isolation) is 
enabled the kernel address space (and therefore the vCPU runstate) will 
not be mapped when running at EL0.
So if you are restoring a vCPU that was executing code at EL0 then 
update_runstate_area will fail as the address is not mapped. There are a 
few solution suggested on the ML (see [1]). However I haven't had time 
to look at properly how to implement them.
KPTI is getting used more widely (e.g meltdown and KASLR). So it would 
be good if we try to solve this problem sooner. I would be happy to 
review patches and/or provide advice if you want to tackle the problem.
Cheers,

[1] https://lists.xen.org/archives/html/xen-devel/2018-03/msg00223.html

--
Julien Grall

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel