NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.9 NOTICE: BL2: PRR is R-Car H3 ES1.1 NOTICE: BL2: Boot device is HyperFlash(80MHz) NOTICE: BL2: LCM state is CM NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x52 NOTICE: BL2: DDR2400(rev.0.15) NOTICE: BL2: DRAM Split is 4ch NOTICE: BL2: QoS is default setting(rev.0.32) NOTICE: BL2: v1.1(release):3ad02ac NOTICE: BL2: Built : 15:16:01, Feb 15 2017 NOTICE: BL2: Normal boot NOTICE: BL2: dst=0xe631a208 src=0x8180000 len=512(0x200) NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800) NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000) NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000) NOTICE: BL2: dst=0x49000000 src=0x8640000 len=1048576(0x100000) U-Boot 2015.04 (Feb 15 2017 - 15:16:02) CPU: Renesas Electronics R8A7795 rev 1.1 Board: Salvator-X I2C: ready DRAM: 3.9 GiB MMC: sh-sdhi: 0, sh-sdhi: 1, sh-sdhi: 2 In: serial Out: serial Err: serial Net: ravb Hit any key to stop autoboot: 0 ravb Waiting for PHY auto negotiation to complete.. done ravb: 100Base/Full Using ravb device TFTP from server 192.168.1.100; our IP address is 192.168.1.1 Filename 'xen-uImage'. Load address: 0x48080000 Loading: ################################################################# ################################################################# ########### 129.9 KiB/s done Bytes transferred = 721296 (b0190 hex) ravb:0 is connected to ravb. Reconnecting to ravb ravb Waiting for PHY auto negotiation to complete.. done ravb: 100Base/Full Using ravb device TFTP from server 192.168.1.100; our IP address is 192.168.1.1 Filename 'r8a7795-salvator-x-dom0.dtb'. Load address: 0x48000000 Loading: ############# 12.7 KiB/s done Bytes transferred = 65776 (100f0 hex) ravb:0 is connected to ravb. Reconnecting to ravb ravb Waiting for PHY auto negotiation to complete.. done ravb: 100Base/Full Using ravb device TFTP from server 192.168.1.100; our IP address is 192.168.1.1 Filename 'Image'. Load address: 0x7a000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 1.1 MiB/s done Bytes transferred = 15068160 (e5ec00 hex) ravb:0 is connected to ravb. Reconnecting to ravb ravb Waiting for PHY auto negotiation to complete.. done ravb: 100Base/Full Using ravb device TFTP from server 192.168.1.100; our IP address is 192.168.1.1 Filename 'xenpolicy-4.8.0'. Load address: 0x7c000000 Loading: ### 2 KiB/s done Bytes transferred = 10258 (2812 hex) ## Booting kernel from Legacy Image at 48080000 ... Image Name: XEN Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 721232 Bytes = 704.3 KiB Load Address: 78080000 Entry Point: 78080000 Verifying Checksum ... OK ## Flattened Device Tree blob at 48000000 Booting using the fdt blob at 0x48000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000048000000, end 00000000480130ef Starting kernel ... Xen 4.9.0 (XEN) Xen version 4.9.0 (teltvm0881@) (aarch64-linux-gnu-gcc (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609) debug=n Wed Aug 9 17:42:27 IST 2017 (XEN) Latest ChangeSet: Tue Jun 27 19:13:19 2017 +0100 git:c30bf55 (XEN) Processor: 411fd073: "ARM Limited", variant: 0x1, part 0xd07, rev 0x3 (XEN) 64-bit Execution: (XEN) Processor Features: 0000000000002222 0000000000000000 (XEN) Exception Levels: EL3:64+32 EL2:64+32 EL1:64+32 EL0:64+32 (XEN) Extensions: FloatingPoint AdvancedSIMD (XEN) Debug Features: 0000000010305106 0000000000000000 (XEN) Auxiliary Features: 0000000000000000 0000000000000000 (XEN) Memory Model Features: 0000000000001124 0000000000000000 (XEN) ISA Features: 0000000000011120 0000000000000000 (XEN) 32-bit Execution: (XEN) Processor Features: 00000131:00011011 (XEN) Instruction Sets: AArch32 A32 Thumb Thumb-2 Jazelle (XEN) Extensions: GenericTimer Security (XEN) Debug Features: 03010066 (XEN) Auxiliary Features: 00000000 (XEN) Memory Model Features: 10201105 40000000 01260000 02102211 (XEN) ISA Features: 02101110 13112111 21232042 01112131 00011142 00011121 (XEN) Using PSCI-1.0 for SMP bringup (XEN) SMP: Allowing 8 CPUs (XEN) Generic Timer IRQ: phys=30 hyp=26 virt=27 Freq: 8333 KHz (XEN) GICv2 initialization: (XEN) gic_dist_addr=00000000f1010000 (XEN) gic_cpu_addr=00000000f1020000 (XEN) gic_hyp_addr=00000000f1040000 (XEN) gic_vcpu_addr=00000000f1060000 (XEN) gic_maintenance_irq=25 (XEN) GICv2: Adjusting CPU interface base to 0xf102f000 (XEN) GICv2: 512 lines, 8 cpus, secure (IID 0200043b). (XEN) Using scheduler: SMP Credit Scheduler (credit) (XEN) Allocated console ring of 64 KiB. (XEN) Bringing up CPU1 (XEN) CPU 1 booted. (XEN) Bringing up CPU2 (XEN) CPU 2 booted. (XEN) Bringing up CPU3 (XEN) CPU 3 booted. (XEN) Bringing up CPU4 (XEN) Failed to bring up CPU4 (XEN) Failed to bring up CPU 4 (error -6) (XEN) Bringing up CPU5 (XEN) Failed to bring up CPU5 (XEN) Failed to bring up CPU 5 (error -6) (XEN) Bringing up CPU6 (XEN) Failed to bring up CPU6 (XEN) Failed to bring up CPU 6 (error -6) (XEN) Bringing up CPU7 (XEN) Failed to bring up CPU7 (XEN) Failed to bring up CPU 7 (error -6) (XEN) Brought up 4 CPUs (XEN) P2M: 44-bit IPA with 44-bit PA and 8-bit VMID (XEN) P2M: 4 levels with order-0 root, VTCR 0x80043594 (XEN) I/O virtualisation disabled (XEN) build-id: e31f3827009f1430feb9975ad03cac8eb5893e66 (XEN) alternatives: Patching with alt table 00000000400bad28 -> 00000000400bb1fc (XEN) *** LOADING DOMAIN 0 *** (XEN) Loading kernel from boot module @ 000000007a000000 (XEN) Allocating 1:1 mappings totalling 2048MB for dom0: (XEN) BANK[0] 0x00000050000000-0x00000078000000 (640MB) (XEN) BANK[1] 0x00000600000000-0x00000640000000 (1024MB) (XEN) BANK[2] 0x00000718000000-0x00000730000000 (384MB) (XEN) Grant table range: 0x0000073fe00000-0x0000073fe58000 (XEN) Loading zImage from 000000007a000000 to 0000000050080000-0000000052080000 (XEN) Allocating PPI 16 for event channel interrupt (XEN) Loading dom0 DTB to 0x0000000058000000-0x000000005800f7dc (XEN) Std. Loglevel: All (XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings) (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen) (XEN) Freed 268kB init memory. (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER4 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER8 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER12 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER16 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER20 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER24 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER28 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER32 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER36 (XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER40 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.6.0-yocto-standard (test2039@teltvm2039x) (gcc version 5.2.1 20151005 (Linaro GCC 5.2-2015.11-2) ) #3 SMP PREEMPT Wed Mar 29 15:03:46 IST 2017 [ 0.000000] Boot CPU: AArch64 Processor [411fd073] [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 128 MiB at 0x0000000070000000 [ 0.000000] On node 0 totalpages: 524288 [ 0.000000] DMA zone: 2560 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 163840 pages, LIFO batch:31 [ 0.000000] Normal zone: 5632 pages used for memmap [ 0.000000] Normal zone: 360448 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] Xen 4.9 support found [ 0.000000] percpu: Embedded 20 pages/cpu @ffffffc6eff1d000 s43776 r8192 d29952 u81920 [ 0.000000] pcpu-alloc: s43776 r8192 d29952 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 516096 [ 0.000000] Kernel command line: console=hvc0 root=/dev/nfs nfsroot=192.168.1.100:/exports/rfs_xen/ ip=192.168.1.1:192.168.1.100 rw rootwait ignore_loglevel cma=128M [ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes [ 0.000000] log_buf_len min size: 16384 bytes [ 0.000000] log_buf_len: 32768 bytes [ 0.000000] early log buf free: 14588(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] software IO TLB [mem 0x6bfff000-0x6ffff000] (64MB) mapped at [ffffffc02bfff000-ffffffc02fffefff] [ 0.000000] Memory: 1831816K/2097152K available (9032K kernel code, 763K rwdata, 3956K rodata, 960K init, 318K bss, 134264K reserved, 131072K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008940000 ( 8960 KB) [ 0.000000] .rodata : 0xffffff8008940000 - 0xffffff8008d30000 ( 4032 KB) [ 0.000000] .init : 0xffffff8008d30000 - 0xffffff8008e20000 ( 960 KB) [ 0.000000] .data : 0xffffff8008e20000 - 0xffffff8008edec00 ( 763 KB) [ 0.000000] .bss : 0xffffff8008edec00 - 0xffffff8008f2e7f0 ( 319 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00400000 - 0xffffffbf1bc00000 ( 440 MB actual) [ 0.000000] memory : 0xffffffc010000000 - 0xffffffc6f0000000 ( 28160 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] Architected cp15 timer(s) running at 8.33MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns [ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns [ 0.000282] Console: colour dummy device 80x25 [ 0.364671] console [hvc0] enabled [ 0.368137] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333) [ 0.378409] pid_max: default: 32768 minimum: 301 [ 0.383113] Security Framework initialized [ 0.387247] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.393966] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.401729] ASID allocator initialised with 65536 entries [ 0.407149] xen:grant_table: Grant tables using version 1 layout [ 0.413101] Grant table initialized [ 0.416642] xen:events: Using FIFO-based ABI [ 0.420950] Xen: initializing cpu0 [ 0.442041] EFI services will not be available. [ 0.470625] Detected PIPT I-cache on CPU1 [ 0.470691] Xen: initializing cpu1 [ 0.470708] CPU1: Booted secondary processor [411fd073] [ 0.486654] Detected PIPT I-cache on CPU2 [ 0.486699] Xen: initializing cpu2 [ 0.486714] CPU2: Booted secondary processor [411fd073] [ 0.502699] Detected PIPT I-cache on CPU3 [ 0.502742] Xen: initializing cpu3 [ 0.502755] CPU3: Booted secondary processor [411fd073] [ 0.502806] Brought up 4 CPUs [ 0.544043] SMP: Total of 4 processors activated. [ 0.548800] CPU features: detected feature: 32-bit EL0 Support [ 0.554676] CPU: All CPU(s) started at EL1 [ 0.559379] devtmpfs: initialized [ 0.568615] DMI not present or invalid. [ 0.572579] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.583911] pinctrl core: initialized pinctrl subsystem [ 0.590381] NET: Registered protocol family 16 [ 0.596087] vdso: 2 pages (1 code @ ffffff8008946000, 1 data @ ffffff8008e24000) [ 0.603404] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.610715] DMA: preallocated 256 KiB pool for atomic allocations [ 0.616786] xen:swiotlb_xen: Warning: only able to allocate 4 MB for software IO TLB [ 0.625297] software IO TLB [mem 0x6b800000-0x6bc00000] (4MB) mapped at [ffffffc02b800000-ffffffc02bbfffff] [ 0.635108] Serial: AMBA PL011 UART driver [ 0.643525] sh-pfc e6060000.pfc: r8a77950_pfc support registered [ 0.649662] renesas_irqc e61c0000.interrupt-controller: failed to add to PM domain always-on: -517 [ 0.666506] rcar_hwspinlock e62600c0.mfis-lock: failed to add to PM domain always-on: -517 [ 0.691536] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.699294] ACPI: Interpreter disabled. [ 0.703096] xen:balloon: Initialising balloon driver [ 0.708226] xen_balloon: Initialising balloon driver [ 0.714632] vgaarb: loaded [ 0.717478] SCSI subsystem initialized [ 0.721287] libata version 3.00 loaded. [ 0.725261] usbcore: registered new interface driver usbfs [ 0.730681] usbcore: registered new interface driver hub [ 0.736074] usbcore: registered new device driver usb [ 0.741665] media: Linux media interface: v0.10 [ 0.746130] Linux video capture interface: v2.00 [ 0.750794] pps_core: LinuxPPS API ver. 1 registered [ 0.755785] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.764948] PTP clock support registered [ 0.769040] dmi: Firmware registration failed. [ 0.774752] Advanced Linux Sound Architecture Driver Initialized. [ 0.781536] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 100000 Hz [ 0.788853] clocksource: Switched to clocksource arch_sys_counter [ 0.794943] VFS: Disk quotas dquot_6.6.0 [ 0.798859] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.805952] pnp: PnP ACPI: disabled [ 0.815100] /soc/thermal-zones/sensor-thermal3/cooling-maps/map0: could not find phandle [ 0.823095] missing cooling_device property [ 0.827323] failed to build thermal zone sensor-thermal3: -22 [ 0.833194] NET: Registered protocol family 2 [ 0.837871] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.845036] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 0.851784] TCP: Hash tables configured (established 16384 bind 16384) [ 0.858273] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 0.864272] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 0.870840] NET: Registered protocol family 1 [ 0.875372] RPC: Registered named UNIX socket transport module. [ 0.881226] RPC: Registered udp transport module. [ 0.885947] RPC: Registered tcp transport module. [ 0.890697] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.897190] PCI: CLS 0 bytes, default 128 [ 0.901663] /soc/pmu_a57: could not find phandle [ 0.906270] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 1 counters available [ 0.914437] /soc/pmu_a53: could not find phandle [ 0.919101] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 1 counters available [ 0.927596] kvm [1]: HYP mode not available [ 0.934007] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.940262] audit: initializing netlink subsys (disabled) [ 0.945649] audit: type=2000 audit(0.723:1): initialized [ 0.951582] workingset: timestamp_bits=44 max_order=19 bucket_order=0 [ 0.963328] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.969980] NFS: Registering the id_resolver key type [ 0.974980] Key type id_resolver registered [ 0.979303] Key type id_legacy registered [ 0.983403] fuse init (API version 7.24) [ 0.987579] 9p: Installing v9fs 9p2000 file system support [ 0.994930] io scheduler noop registered [ 0.998896] io scheduler cfq registered (default) [ 1.007461] gpio_rcar e6050000.gpio: driving 16 GPIOs [ 1.012750] gpio_rcar e6051000.gpio: driving 28 GPIOs [ 1.017958] gpio_rcar e6052000.gpio: driving 15 GPIOs [ 1.023155] gpio_rcar e6053000.gpio: driving 16 GPIOs [ 1.028356] gpio_rcar e6054000.gpio: driving 18 GPIOs [ 1.033568] gpio_rcar e6055000.gpio: driving 26 GPIOs [ 1.038786] gpio_rcar e6055400.gpio: driving 32 GPIOs [ 1.043954] gpio_rcar e6055800.gpio: driving 4 GPIOs [ 1.049986] PCI host bridge /soc/pcie@fe000000 ranges: [ 1.055051] IO 0xfe100000..0xfe1fffff -> 0x00000000 [ 1.060217] MEM 0xfe200000..0xfe3fffff -> 0xfe200000 [ 1.065403] MEM 0x30000000..0x37ffffff -> 0x30000000 [ 1.070582] MEM 0x38000000..0x3fffffff -> 0x38000000 [ 1.125859] rcar-pcie fe000000.pcie: PCIe link down [ 1.130710] PCI host bridge /soc/pcie@ee800000 ranges: [ 1.135831] IO 0xee900000..0xee9fffff -> 0x00000000 [ 1.141011] MEM 0xeea00000..0xeebfffff -> 0xeea00000 [ 1.146194] MEM 0xc0000000..0xc7ffffff -> 0xc0000000 [ 1.151376] MEM 0xc8000000..0xcfffffff -> 0xc8000000 [ 1.206628] rcar-pcie ee800000.pcie: PCIe link down [ 1.225523] xen:xen_evtchn: Event-channel device installed [ 1.233130] bd9571mwv 7-0030: bd9571mwv probed [ 1.240999] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.248936] SuperH (H)SCI(F) driver initialized [ 1.253908] e6e68000.serial: ttySC1 at MMIO 0xe6e68000 (irq = 139, base_baud = 0) is a scif [ 1.262760] msm_serial: driver initialized [ 1.267125] [drm] Initialized drm 1.1.0 20060810 [ 1.272337] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.278856] [drm] No driver support for vblank timestamp query. [ 1.284947] rcar-du feb00000.display: failed to initialize DRM/KMS (-517) [ 1.292712] Unable to detect cache hierarchy from DT for CPU 0 [ 1.301553] loop: module loaded [ 1.306510] scsi host0: sata_rcar [ 1.309893] ata1: SATA max UDMA/133 irq 161 [ 1.315432] spi_sh_msiof e6ea0000.spi: DMA available [ 1.321482] tun: Universal TUN/TAP device driver, 1.6 [ 1.326440] tun: (C) 1999-2004 Max Krasnyansky [ 1.332851] CAN device driver interface [ 1.337206] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.342937] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.348947] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.355902] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.361551] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.0.2-k [ 1.369374] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.375373] sky2: driver version 1.30 [ 1.379607] libphy: ravb_mii: probed [ 1.383827] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:0a:00:a3:6c, IRQ 136. [ 1.393166] VFIO - User Level meta-driver version: 0.3 [ 1.399117] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.405565] ehci-pci: EHCI PCI platform driver [ 1.410073] ehci-platform: EHCI generic platform driver [ 1.415643] ehci-platform ee0a0100.usb: EHCI Host Controller [ 1.421230] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 1 [ 1.429228] ehci-platform ee0a0100.usb: irq 169, io mem 0xee0a0100 [ 1.444858] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10 [ 1.451332] hub 1-0:1.0: USB hub found [ 1.455019] hub 1-0:1.0: 1 port detected [ 1.459234] ehci-platform ee0c0100.usb: EHCI Host Controller [ 1.464807] ehci-platform ee0c0100.usb: new USB bus registered, assigned bus number 2 [ 1.472759] ehci-platform ee0c0100.usb: irq 170, io mem 0xee0c0100 [ 1.488859] ehci-platform ee0c0100.usb: USB 2.0 started, EHCI 1.10 [ 1.495260] hub 2-0:1.0: USB hub found [ 1.498928] hub 2-0:1.0: 1 port detected [ 1.503141] ehci-msm: Qualcomm On-Chip EHCI Host Controller [ 1.508772] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.514865] ohci-pci: OHCI PCI platform driver [ 1.519389] ohci-platform: OHCI generic platform driver [ 1.524835] ohci-platform ee0a0000.usb: Generic Platform OHCI controller [ 1.531441] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 3 [ 1.539390] ohci-platform ee0a0000.usb: irq 169, io mem 0xee0a0000 [ 1.631185] hub 3-0:1.0: USB hub found [ 1.634854] hub 3-0:1.0: 1 port detected [ 1.639035] ohci-platform ee0c0000.usb: Generic Platform OHCI controller [ 1.645638] ohci-platform ee0c0000.usb: new USB bus registered, assigned bus number 4 [ 1.653554] ohci-platform ee0c0000.usb: irq 170, io mem 0xee0c0000 [ 1.720858] ata1: link resume succeeded after 1 retries [ 1.743185] hub 4-0:1.0: USB hub found [ 1.746855] hub 4-0:1.0: 1 port detected [ 1.751353] xhci-hcd ee000000.usb: xHCI Host Controller [ 1.756491] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 5 [ 1.780022] xhci-hcd ee000000.usb: hcc params 0x014051ce hci version 0x100 quirks 0x00830010 [ 1.788380] xhci-hcd ee000000.usb: irq 162, io mem 0xee000000 [ 1.794455] hub 5-0:1.0: USB hub found [ 1.798127] hub 5-0:1.0: 1 port detected [ 1.802226] xhci-hcd ee000000.usb: xHCI Host Controller [ 1.807361] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 6 [ 1.814828] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.823195] hub 6-0:1.0: USB hub found [ 1.826863] hub 6-0:1.0: 1 port detected [ 1.831217] usbcore: registered new interface driver usb-storage [ 1.832303] ata1: SATA link down (SStatus 0 SControl 300) [ 1.844666] renesas_usbhs e6590000.usb: probe failed (-517) [ 1.850601] mousedev: PS/2 mouse device common for all mice [ 1.856326] usbcore: registered new interface driver usbtouchscreen [ 1.863042] i2c /dev entries driver [ 1.867835] i2c-rcar e6510000.i2c: probed [ 1.872221] i2c-rcar e66d8000.i2c: probed [ 1.876532] adv7482 4-0070: chip found @ 0xe0 (e66d8000.i2c) [ 1.893346] adv7482 4-0070: adv7482 revision is 2143 [ 1.949435] adv7482 4-0070: adv7482 txa power down [ 1.981434] adv7482 4-0070: adv7482 txb power down [ 1.986323] adv7482 4-0070: adv7482 enable csi1 and csi4 [ 1.992668] adv7482 4-0034: chip found @ 0x68 (e66d8000.i2c) [ 2.009327] adv7482 4-0034: adv7482 revision is 2143 [ 2.012861] usb 3-1: new low-speed USB device number 2 using ohci-platform [ 2.073433] adv7482 4-0034: adv7482 txa power down [ 2.105433] adv7482 4-0034: adv7482 txb power down [ 2.110320] adv7482 4-0034: adv7482 enable csi1 and csi4 [ 2.117391] rcar_csi2 fea80000.csi2: Detected YCbCr422 in rcar_csi2_parse_dt [ 2.124451] rcar_csi2 feaa0000.csi2: Detected rgb888 in rcar_csi2_parse_dt [ 2.124860] usb 4-1: new low-speed USB device number 2 using ohci-platform [ 2.138824] soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0 [ 2.145626] adv7482 4-0034: Not detect any video input signal [ 2.151701] adv7482 4-0034: Not detect any video input signal [ 2.157375] rcar_vin e6ef0000.video: multiple subdevices aren't supported yet! [ 2.164940] soc-camera-pdrv soc-camera-pdrv.2: Probing soc-camera-pdrv.2 [ 2.172076] adv7482 4-0070: Not detect any video input signal [ 2.178561] adv7482 4-0070: Not detect any video input signal [ 2.182213] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.190804] rcar_vin e6ef4000.video: multiple subdevices aren't supported yet! [ 2.198842] imr fe860000.imr-lx4: IMR device (pdev: -1) registered as /dev/video2 [ 2.206392] imr fe870000.imr-lx4: IMR device (pdev: -1) registered as /dev/video3 [ 2.213919] imr fe880000.imr-lx4: IMR device (pdev: -1) registered as /dev/video4 [ 2.221463] imr fe890000.imr-lx4: IMR device (pdev: -1) registered as /dev/video5 [ 2.233032] rcar_gen3_thermal e6198000.thermal: Thermal sensor probed [ 2.240802] rcar_gen3_thermal e61a0000.thermal: Thermal sensor probed [ 2.247342] rcar_gen3_thermal e61a8000.thermal: Can't register thermal zone [ 2.254745] renesas_wdt e6020000.wdt: Specified timeout value invalid, using default [ 2.262802] xen_wdt: Xen WatchDog Timer Driver v0.01 [ 2.267927] xen_wdt: cannot register miscdev on minor=130 (-16) [ 2.273756] wdt: probe of wdt failed with error -16 [ 2.278884] cpu cpu0: failed to get clock: -2 [ 2.283159] cpufreq-dt: probe of cpufreq-dt failed with error -2 [ 2.289590] sdhci: Secure Digital Host Controller Interface driver [ 2.290536] hub 6-1:1.0: USB hub found [ 2.291070] hub 6-1:1.0: 4 ports detected [ 2.303532] sdhci: Copyright(c) Pierre Ossman [ 2.308558] sh_mobile_sdhi ee100000.sd: Got CD GPIO [ 2.313369] sh_mobile_sdhi ee100000.sd: Got WP GPIO [ 2.318606] sh_mobile_sdhi ee160000.sd: Got CD GPIO [ 2.323414] sh_mobile_sdhi ee160000.sd: Got WP GPIO [ 2.381002] sh_mobile_sdhi ee140000.mmc: 3.3V signalling voltage failed [ 2.436931] sh_mobile_sdhi ee140000.mmc: mmc0 base at 0xee140000 max clock rate 199 MHz [ 2.445090] Synopsys Designware Multimedia Card Interface Driver [ 2.451575] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.457819] ledtrig-cpu: registered to indicate activity on CPUs [ 2.471606] input: Dell Dell USB Keyboard as /devices/platform/soc/ee0a0000.usb/usb3/3-1/3-1:1.0/0003:413C:2003.0001/input/input0 [ 2.537153] hid-generic 0003:413C:2003.0001: input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-ee0a0000.usb-1/input0 [ 2.555399] input: USB Optical Mouse as /devices/platform/soc/ee0c0000.usb/usb4/4-1/4-1:1.0/0003:0461:4D15.0002/input/input1 [ 2.566663] hid-generic 0003:0461:4D15.0002: input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-ee0c0000.usb-1/input0 [ 2.577464] usbcore: registered new interface driver usbhid [ 2.583033] usbhid: USB HID core driver [ 2.587633] 5p49v5923a 4-006a: Rev.0xff, probed [ 2.597399] cs2000-cp 2-004f: revision - C1 [ 2.602783] ak4613-codec 2-0010: No cache used with register defaults set! [ 2.615149] rcar_sound ec500000.sound: probed [ 2.619641] Netfilter messages via NETLINK v0.30. [ 2.624433] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 2.630575] ctnetlink v0.93: registering with nfnetlink. [ 2.635854] nf_tables: (c) 2007-2009 Patrick McHardy [ 2.642374] nf_tables_compat: (c) 2012 Pablo Neira Ayuso [ 2.649967] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.655627] NET: Registered protocol family 10 [ 2.660822] sit: IPv6 over IPv4 tunneling driver [ 2.665684] NET: Registered protocol family 17 [ 2.670072] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.672196] mmc0: new HS200 MMC card at address 0001 [ 2.676517] mmcblk0: mmc0:0001 BGSD3R 29.1 GiB [ 2.676655] mmcblk0boot0: mmc0:0001 BGSD3R partition 1 16.0 MiB [ 2.680801] mmcblk0boot1: mmc0:0001 BGSD3R partition 2 16.0 MiB [ 2.680953] mmcblk0rpmb: mmc0:0001 BGSD3R partition 3 4.00 MiB [ 2.683588] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 [ 2.714739] Bridge firewalling registered [ 2.718773] can: controller area network core (rev 20120528 abi 9) [ 2.725039] NET: Registered protocol family 29 [ 2.729485] can: raw protocol (rev 20120528) [ 2.733857] 9pnet: Installing 9P2000 support [ 2.738184] Key type dns_resolver registered [ 2.742957] registered taskstats version 1 [ 2.747215] /soc/thermal-zones/emergency: could not find phandle [ 2.753132] /soc/thermal-zones/emergency: could not find phandle [ 2.759183] /soc/thermal-zones/emergency: could not find phandle [ 2.765238] /soc/thermal-zones/emergency: could not find phandle [ 2.771278] /soc/thermal-zones/emergency: could not find phandle [ 2.777321] /soc/thermal-zones/emergency: could not find phandle [ 2.783387] /soc/thermal-zones/emergency: could not find phandle [ 2.789415] /soc/thermal-zones/emergency: could not find phandle [ 2.795469] /soc/thermal-zones/emergency: could not find phandle [ 2.801525] /soc/thermal-zones/emergency: could not find phandle [ 2.807566] /soc/thermal-zones/emergency: could not find phandle [ 2.813609] /soc/thermal-zones/emergency: could not find phandle [ 2.819645] thermal emergency: shutdown cpu none [ 2.824333] thermal emergency: set temperature to 110 celsius [ 2.828864] usb 5-1: new high-speed USB device number 2 using xhci-hcd [ 2.837035] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs [ 2.844580] phy_rcar_gen3_usb2 ee080200.usb-phy: Unbalanced pm_runtime_enable! [ 2.852663] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.859191] [drm] No driver support for vblank timestamp query. [ 2.865957] rcar-du feb00000.display: Detected HDMI controller 0x20:0x1a:0xa0:0xc1 [ 2.873767] rcar-du feb00000.display: registered DesignWare HDMI I2C bus driver [ 2.881158] rcar-du feb00000.display: Detected HDMI controller 0x20:0x1a:0xa0:0xc1 [ 2.888871] rcar-du feb00000.display: registered DesignWare HDMI I2C bus driver [ 2.965535] hub 5-1:1.0: USB hub found [ 2.969690] hub 5-1:1.0: 4 ports detected [ 3.155453] Console: switching to colour frame buffer device 128x48 [ 3.164486] rcar-du feb00000.display: fb0: frame buffer device [ 3.181393] [drm] Device feb00000.display probed [ 3.186562] ehci-platform ee080100.usb: EHCI Host Controller [ 3.192146] ehci-platform ee080100.usb: new USB bus registered, assigned bus number 7 [ 3.200168] ehci-platform ee080100.usb: irq 168, io mem 0xee080100 [ 3.216874] ehci-platform ee080100.usb: USB 2.0 started, EHCI 1.10 [ 3.223345] hub 7-0:1.0: USB hub found [ 3.227017] hub 7-0:1.0: 1 port detected [ 3.231438] ohci-platform ee080000.usb: Generic Platform OHCI controller [ 3.238066] ohci-platform ee080000.usb: new USB bus registered, assigned bus number 8 [ 3.246012] ohci-platform ee080000.usb: irq 168, io mem 0xee080000 [ 3.304868] usb 5-1.1: new high-speed USB device number 3 using xhci-hcd [ 3.335228] hub 8-0:1.0: USB hub found [ 3.338900] hub 8-0:1.0: 1 port detected [ 3.343444] renesas_usbhs e6590000.usb: transceiver found [ 3.348851] renesas_usbhs e6590000.usb: gadget probed [ 3.353890] renesas_usbhs e6590000.usb: probed [ 3.359051] rcar_gen3_thermal e61a8000.thermal: Can't register thermal zone [ 3.366580] sh_mobile_sdhi ee100000.sd: Got CD GPIO [ 3.371395] sh_mobile_sdhi ee100000.sd: Got WP GPIO [ 3.417020] usb-storage 5-1.1:1.0: USB Mass Storage device detected [ 3.423466] scsi host1: usb-storage 5-1.1:1.0 [ 3.477032] sh_mobile_sdhi ee100000.sd: mmc1 base at 0xee100000 max clock rate 199 MHz [ 3.485407] sh_mobile_sdhi ee160000.sd: Got CD GPIO [ 3.490252] sh_mobile_sdhi ee160000.sd: Got WP GPIO [ 3.512861] usb 5-1.2: new full-speed USB device number 4 using xhci-hcd [ 3.597002] sh_mobile_sdhi ee160000.sd: mmc2 base at 0xee160000 max clock rate 199 MHz [ 3.605523] asoc-simple-card sound: ak4613-hifi <-> ec500000.sound mapping ok [ 3.620312] rcar_gen3_thermal e61a8000.thermal: Can't register thermal zone [ 3.627752] hctosys: unable to open rtc device (rtc0) [ 3.644743] input: Logitech G29 Driving Force Racing Wheel as /devices/platform/soc/ee000000.usb/usb5/5-1/5-1.2/5-1.2:1.0/0003:046D:C294.0003/input/input2 [ 3.658613] logitech 0003:046D:C294.0003: input: USB HID v1.00 Gamepad [Logitech G29 Driving Force Racing Wheel] on usb-ee000000.usb-1.2/input0 [ 3.671380] logitech: probe of 0003:046D:C294.0003 failed with error -1 [ 3.678888] rcar_gen3_thermal e61a8000.thermal: Can't register thermal zone [ 3.703735] Micrel KSZ9031 Gigabit PHY e6800000.etherne:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.etherne:00, irq=255) [ 3.717673] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.425603] scsi 1:0:0:0: Direct-Access SanDisk Cruzer Mini 0.4 PQ: 0 ANSI: 2 [ 4.434362] sd 1:0:0:0: [sda] 1000944 512-byte logical blocks: (512 MB/489 MiB) [ 4.434641] rcar_gen3_thermal e61a8000.thermal: Can't register thermal zone [ 4.448910] sd 1:0:0:0: [sda] Write Protect is off [ 4.453620] sd 1:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 4.458992] sd 1:0:0:0: [sda] No Caching mode page found [ 4.464206] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 4.472745] sda: sda1 [ 4.476064] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 6.258043] ravb e6800000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 6.260884] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.276861] IP-Config: Guessing netmask 255.255.255.0 [ 6.281889] IP-Config: Complete: [ 6.285114] device=eth0, hwaddr=2e:09:0a:00:a3:6c, ipaddr=192.168.1.1, mask=255.255.255.0, gw=255.255.255.255 [ 6.295467] host=192.168.1.1, domain=, nis-domain=(none) [ 6.301260] bootserver=192.168.1.100, rootserver=192.168.1.100, rootpath= [ 6.308531] SDHI0 Vcc: disabling [ 6.311802] SDHI3 Vcc: disabling [ 6.315082] SDHI0 VccQ: disabling [ 6.318448] SDHI3 VccQ: disabling [ 6.322133] ALSA device list: [ 6.325015] #0: rsnd-dai.0-ak4613-hifi [ 7.718459] random: nonblocking pool is initialized [ 131.576859] mount: server 192.168.1.100 not responding, timed out [ 316.856903] VFS: Unable to mount root fs via NFS, trying floppy. [ 316.863043] VFS: Cannot open root device "nfs" or unknown-block(2,0): error -6 [ 316.870176] Please append a correct "root=" boot option; here are the available partitions: [ 316.878566] b300 30535680 mmcblk0 driver: mmcblk [ 316.883892] b301 1024 mmcblk0p1 d117f98e-6f2c-d04b-a5b2-331a19f91cb2 [ 316.891408] b302 16384 mmcblk0p2 25718777-d0ad-7443-9e60-02cb591c9737 [ 316.898925] b303 16384 mmcblk0p3 8a4bb8b4-e304-ae48-8536-aff5c9c495b1 [ 316.906442] b304 16384 mmcblk0p4 08992135-13c6-084b-9322-3391ff571e19 [ 316.913958] b305 2097152 mmcblk0p5 333a128e-d3e3-b94d-92f4-d3ebd9b3224f [ 316.921475] b306 262144 mmcblk0p6 f20aa902-1c5d-294a-9177-97a513e3cae4 [ 316.928999] b307 524288 mmcblk0p7 db88503d-34a5-3e41-836d-c757cb682814 [ 316.936508] b308 16384 mmcblk0p8 012b3303-34ac-284d-99b4-34e03a2335f4 [ 316.944032] b309 27552751 mmcblk0p9 faec2ecf-8544-e241-b19d-757e796da607 [ 316.951547] b360 4096 mmcblk0rpmb (driver?) [ 316.956813] b340 16384 mmcblk0boot1 (driver?) [ 316.962170] b320 16384 mmcblk0boot0 (driver?) [ 316.967526] 0800 500472 sda driver: sd [ 316.972191] 0801 500440 sda1 000315bc-01 [ 316.977116] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) [ 316.985417] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-yocto-standard #3 [ 316.992580] Hardware name: Renesas Salvator-X board based on r8a7795 (DT) [ 316.999406] Call trace: [ 317.001923] [] dump_backtrace+0x0/0x1a8 [ 317.007357] [] show_stack+0x14/0x20 [ 317.012460] [] dump_stack+0x94/0xb8 [ 317.017555] [] panic+0x110/0x25c [ 317.022393] [] mount_block_root+0x188/0x264 [ 317.028178] [] mount_root+0x118/0x130 [ 317.033448] [] prepare_namespace+0x13c/0x184 [ 317.039324] [] kernel_init_freeable+0x1cc/0x1f0 [ 317.045464] [] kernel_init+0x10/0x100 [ 317.050730] [] ret_from_fork+0x10/0x40 [ 317.056085] SMP: stopping secondary CPUs [ 317.060075] Kernel Offset: disabled [ 317.063601] Memory Limit: none [ 317.066716] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)