[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] [RFC 12/22] x86/boot/64: Adapt assembly for PIE support



Change the assembly code to use only relative references of symbols for the
kernel to be PIE compatible.

Early at boot, the kernel is mapped at a temporary address while preparing
the page table. To know the changes needed for the page table with KASLR,
the boot code calculate the difference between the expected address of the
kernel and the one chosen by KASLR. It does not work with PIE because all
symbols in code are relatives. Instead of getting the future relocated
virtual address, you will get the current temporary mapping. The solution
is using global variables that will be relocated as expected.

Position Independent Executable (PIE) support will allow to extended the
KASLR randomization range below the -2G memory limit.

Signed-off-by: Thomas Garnier <thgarnie@xxxxxxxxxx>
---
 arch/x86/kernel/head_64.S | 32 ++++++++++++++++++++++++--------
 1 file changed, 24 insertions(+), 8 deletions(-)

diff --git a/arch/x86/kernel/head_64.S b/arch/x86/kernel/head_64.S
index 6225550883df..7e4f7a83a15a 100644
--- a/arch/x86/kernel/head_64.S
+++ b/arch/x86/kernel/head_64.S
@@ -78,8 +78,23 @@ startup_64:
        call    __startup_64
        popq    %rsi
 
-       movq    $(early_top_pgt - __START_KERNEL_map), %rax
+       movq    _early_top_pgt_offset(%rip), %rax
        jmp 1f
+
+       /*
+        * Position Independent Code takes only relative references in code
+        * meaning a global variable address is relative to RIP and not its
+        * future virtual address. Global variables can be used instead as they
+        * are still relocated on the expected kernel mapping address.
+        */
+       .align 8
+_early_top_pgt_offset:
+       .quad early_top_pgt - __START_KERNEL_map
+_init_top_offset:
+       .quad init_top_pgt - __START_KERNEL_map
+_va_jump:
+       .quad 2f
+
 ENTRY(secondary_startup_64)
        /*
         * At this point the CPU runs in 64bit mode CS.L = 1 CS.D = 0,
@@ -98,7 +113,8 @@ ENTRY(secondary_startup_64)
        /* Sanitize CPU configuration */
        call verify_cpu
 
-       movq    $(init_top_pgt - __START_KERNEL_map), %rax
+       movq    _init_top_offset(%rip), %rax
+
 1:
 
        /* Enable PAE mode, PGE and LA57 */
@@ -113,9 +129,8 @@ ENTRY(secondary_startup_64)
        movq    %rax, %cr3
 
        /* Ensure I am executing from virtual addresses */
-       movq    $1f, %rax
-       jmp     *%rax
-1:
+       jmp     *_va_jump(%rip)
+2:
 
        /* Check if nx is implemented */
        movl    $0x80000001, %eax
@@ -211,11 +226,12 @@ ENTRY(secondary_startup_64)
         *      REX.W + FF /5 JMP m16:64 Jump far, absolute indirect,
         *              address given in m16:64.
         */
-       pushq   $.Lafter_lret   # put return address on stack for unwinder
+       leaq    .Lafter_lret(%rip), %rax
+       pushq   %rax            # put return address on stack for unwinder
        xorq    %rbp, %rbp      # clear frame pointer
-       movq    initial_code(%rip), %rax
+       leaq    initial_code(%rip), %rax
        pushq   $__KERNEL_CS    # set correct cs
-       pushq   %rax            # target address in negative space
+       pushq   (%rax)          # target address in negative space
        lretq
 .Lafter_lret:
 ENDPROC(secondary_startup_64)
-- 
2.13.2.932.g7449e964c-goog


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
https://lists.xen.org/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.