[Xen-devel] [PATCH 16/17 v5] xen/arm: vpl011: Add a pl011 uart DT node in the guest device tree

[Bhupinder Thakur <bhupinder.thakur@xxxxxxxxxx>]

The SBSA UART node format is as specified in
Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt and given below:

ARM SBSA defined generic UART
------------------------------
This UART uses a subset of the PL011 registers and consequently lives
in the PL011 driver. It's baudrate and other communication parameters
cannot be adjusted at runtime, so it lacks a clock specifier here.

Required properties:
- compatible: must be "arm,sbsa-uart"
- reg: exactly one register range
- interrupts: exactly one interrupt specifier
- current-speed: the (fixed) baud rate set by the firmware

Currently the baud rate of 115200 has been selected as a default value,
which is one of the valid baud rate setttings. Higher baud rate was
selected since an emulated pl011 can support any valid baud rate without
any limitation of the hardware.

Signed-off-by: Bhupinder Thakur <bhupinder.thakur@xxxxxxxxxx>
Reviewed-by: Stefano Stabellini <sstabellini@xxxxxxxxxx>
---
CC: Ian Jackson <ian.jackson@xxxxxxxxxxxxx>
CC: Wei Liu <wei.liu2@xxxxxxxxxx>
CC: Stefano Stabellini <sstabellini@xxxxxxxxxx>
CC: Julien Grall <julien.grall@xxxxxxx>

 tools/libxl/libxl_arm.c | 52 +++++++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 50 insertions(+), 2 deletions(-)

diff --git a/tools/libxl/libxl_arm.c b/tools/libxl/libxl_arm.c
index 9d6448e..cf3de01 100644
--- a/tools/libxl/libxl_arm.c
+++ b/tools/libxl/libxl_arm.c
@@ -44,10 +44,22 @@ int libxl__arch_domain_prepare_config(libxl__gc *gc,
     uint32_t nr_spis = 0;
     unsigned int i;
 
+    /*
+     * If pl011 vuart is enabled then increment the nr_spis to allow allocation
+     * of SPI VIRQ for pl011.
+     */
+    if (d_config->b_info.arch_arm.vuart)
+        nr_spis += (GUEST_VPL011_SPI - 32) + 1;
+
     for (i = 0; i < d_config->b_info.num_irqs; i++) {
         uint32_t irq = d_config->b_info.irqs[i];
         uint32_t spi;
 
+        if (d_config->b_info.arch_arm.vuart && (irq == GUEST_VPL011_SPI)) {
+            LOG(ERROR, "Physical IRQ %u conflicting with pl011 SPI\n", irq);
+            return ERROR_FAIL;
+        }
+
         if (irq < 32)
             continue;
 
@@ -130,9 +142,10 @@ static struct arch_info {
     const char *guest_type;
     const char *timer_compat;
     const char *cpu_compat;
+    const char *uart_compat;
 } arch_info[] = {
-    {"xen-3.0-armv7l",  "arm,armv7-timer", "arm,cortex-a15" },
-    {"xen-3.0-aarch64", "arm,armv8-timer", "arm,armv8" },
+    {"xen-3.0-armv7l",  "arm,armv7-timer", "arm,cortex-a15", "arm,sbsa-uart" },
+    {"xen-3.0-aarch64", "arm,armv8-timer", "arm,armv8", "arm,sbsa-uart" },
 };
 
 /*
@@ -590,6 +603,38 @@ static int make_hypervisor_node(libxl__gc *gc, void *fdt,
     return 0;
 }
 
+static int make_vpl011_uart_node(libxl__gc *gc, void *fdt,
+                                 const struct arch_info *ainfo,
+                                 struct xc_dom_image *dom)
+{
+    int res;
+    gic_interrupt intr;
+
+    res = fdt_begin_node(fdt, "sbsa-pl011");
+    if (res) return res;
+
+    res = fdt_property_compat(gc, fdt, 1, ainfo->uart_compat);
+    if (res) return res;
+
+    res = fdt_property_regs(gc, fdt, ROOT_ADDRESS_CELLS, ROOT_SIZE_CELLS,
+                            1,
+                            GUEST_PL011_BASE, GUEST_PL011_SIZE);
+    if (res) return res;
+
+    set_interrupt(intr, GUEST_VPL011_SPI, 0xf, DT_IRQ_TYPE_LEVEL_HIGH);
+
+    res = fdt_property_interrupts(gc, fdt, &intr, 1);
+    if (res) return res;
+
+    /* Use a default baud rate of 115200. */
+    fdt_property_u32(fdt, "current-speed", 115200);
+
+    res = fdt_end_node(fdt);
+    if (res) return res;
+
+    return 0;
+}
+
 static const struct arch_info *get_arch_info(libxl__gc *gc,
                                              const struct xc_dom_image *dom)
 {
@@ -889,6 +934,9 @@ next_resize:
         FDT( make_timer_node(gc, fdt, ainfo, xc_config->clock_frequency) );
         FDT( make_hypervisor_node(gc, fdt, vers) );
 
+        if (info->arch_arm.vuart)
+            FDT( make_vpl011_uart_node(gc, fdt, ainfo, dom) );
+
         if (pfdt)
             FDT( copy_partial_fdt(gc, fdt, pfdt) );
 
-- 
2.7.4


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
https://lists.xen.org/xen-devel