Re: [Xen-devel] [PATCH v3] xen, input: add xen-kbdfront module parameter for setting resolution

[Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>]

On Tue, Apr 11, 2017 at 02:30:37PM +0200, Juergen Gross wrote:
> Add a parameter for setting the resolution of xen-kbdfront in order to
> be able to cope with a (virtual) frame buffer of arbitrary resolution.
> 
> While at it remove the pointless second reading of parameters from
> Xenstore in the device connection phase: all parameters are available
> during device probing already and that is where they should be read.
> 
> Signed-off-by: Juergen Gross <jgross@xxxxxxxx>

Applied, thank you.

> ---
> V3: - merged the two patches
>     - read Xenstore parameters during probing of the device only
> ---
>  drivers/input/misc/xen-kbdfront.c | 39 
> ++++++++++++++-------------------------
>  1 file changed, 14 insertions(+), 25 deletions(-)
> 
> diff --git a/drivers/input/misc/xen-kbdfront.c 
> b/drivers/input/misc/xen-kbdfront.c
> index 3900875dec10..2fc7895373ab 100644
> --- a/drivers/input/misc/xen-kbdfront.c
> +++ b/drivers/input/misc/xen-kbdfront.c
> @@ -41,6 +41,12 @@ struct xenkbd_info {
>       char phys[32];
>  };
>  
> +enum { KPARAM_X, KPARAM_Y, KPARAM_CNT };
> +static int ptr_size[KPARAM_CNT] = { XENFB_WIDTH, XENFB_HEIGHT };
> +module_param_array(ptr_size, int, NULL, 0444);
> +MODULE_PARM_DESC(ptr_size,
> +     "Pointing device width, height in pixels (default 800,600)");
> +
>  static int xenkbd_remove(struct xenbus_device *);
>  static int xenkbd_connect_backend(struct xenbus_device *, struct xenkbd_info 
> *);
>  static void xenkbd_disconnect_backend(struct xenkbd_info *);
> @@ -128,7 +134,12 @@ static int xenkbd_probe(struct xenbus_device *dev,
>       if (!info->page)
>               goto error_nomem;
>  
> +     /* Set input abs params to match backend screen res */
>       abs = xenbus_read_unsigned(dev->otherend, "feature-abs-pointer", 0);
> +     ptr_size[KPARAM_X] = xenbus_read_unsigned(dev->otherend, "width",
> +                                               ptr_size[KPARAM_X]);
> +     ptr_size[KPARAM_Y] = xenbus_read_unsigned(dev->otherend, "height",
> +                                               ptr_size[KPARAM_Y]);
>       if (abs) {
>               ret = xenbus_write(XBT_NIL, dev->nodename,
>                                  "request-abs-pointer", "1");
> @@ -174,8 +185,8 @@ static int xenkbd_probe(struct xenbus_device *dev,
>  
>       if (abs) {
>               __set_bit(EV_ABS, ptr->evbit);
> -             input_set_abs_params(ptr, ABS_X, 0, XENFB_WIDTH, 0, 0);
> -             input_set_abs_params(ptr, ABS_Y, 0, XENFB_HEIGHT, 0, 0);
> +             input_set_abs_params(ptr, ABS_X, 0, ptr_size[KPARAM_X], 0, 0);
> +             input_set_abs_params(ptr, ABS_Y, 0, ptr_size[KPARAM_Y], 0, 0);
>       } else {
>               input_set_capability(ptr, EV_REL, REL_X);
>               input_set_capability(ptr, EV_REL, REL_Y);
> @@ -309,9 +320,6 @@ static void xenkbd_disconnect_backend(struct xenkbd_info 
> *info)
>  static void xenkbd_backend_changed(struct xenbus_device *dev,
>                                  enum xenbus_state backend_state)
>  {
> -     struct xenkbd_info *info = dev_get_drvdata(&dev->dev);
> -     int ret, val;
> -
>       switch (backend_state) {
>       case XenbusStateInitialising:
>       case XenbusStateInitialised:
> @@ -321,15 +329,6 @@ static void xenkbd_backend_changed(struct xenbus_device 
> *dev,
>               break;
>  
>       case XenbusStateInitWait:
> -InitWait:
> -             if (xenbus_read_unsigned(info->xbdev->otherend,
> -                                      "feature-abs-pointer", 0)) {
> -                     ret = xenbus_write(XBT_NIL, info->xbdev->nodename,
> -                                        "request-abs-pointer", "1");
> -                     if (ret)
> -                             pr_warning("xenkbd: can't request abs-pointer");
> -             }
> -
>               xenbus_switch_state(dev, XenbusStateConnected);
>               break;
>  
> @@ -340,17 +339,7 @@ static void xenkbd_backend_changed(struct xenbus_device 
> *dev,
>                * get Connected twice here.
>                */
>               if (dev->state != XenbusStateConnected)
> -                     goto InitWait; /* no InitWait seen yet, fudge it */
> -
> -             /* Set input abs params to match backend screen res */
> -             if (xenbus_scanf(XBT_NIL, info->xbdev->otherend,
> -                              "width", "%d", &val) > 0)
> -                     input_set_abs_params(info->ptr, ABS_X, 0, val, 0, 0);
> -
> -             if (xenbus_scanf(XBT_NIL, info->xbdev->otherend,
> -                              "height", "%d", &val) > 0)
> -                     input_set_abs_params(info->ptr, ABS_Y, 0, val, 0, 0);
> -
> +                     xenbus_switch_state(dev, XenbusStateConnected);
>               break;
>  
>       case XenbusStateClosed:
> -- 
> 2.12.0
> 

-- 
Dmitry

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
https://lists.xen.org/xen-devel