[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] [PATCH v3 05/16] x86/boot: use %ecx instead of %eax



Use %ecx instead of %eax to store low memory upper limit from EBDA.
This way we do not wipe multiboot protocol identifier. It is needed
in reloc() to differentiate between multiboot (v1) and
multiboot2 protocol.

Signed-off-by: Daniel Kiper <daniel.kiper@xxxxxxxxxx>
Reviewed-by: Andrew Cooper <andrew.cooper3@xxxxxxxxxx>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@xxxxxxxxxx>
---
 xen/arch/x86/boot/head.S |   24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/xen/arch/x86/boot/head.S b/xen/arch/x86/boot/head.S
index 28ac721..1ff5937 100644
--- a/xen/arch/x86/boot/head.S
+++ b/xen/arch/x86/boot/head.S
@@ -87,14 +87,14 @@ __start:
         jne     not_multiboot
 
         /* Set up trampoline segment 64k below EBDA */
-        movzwl  0x40e,%eax          /* EBDA segment */
-        cmp     $0xa000,%eax        /* sanity check (high) */
+        movzwl  0x40e,%ecx          /* EBDA segment */
+        cmp     $0xa000,%ecx        /* sanity check (high) */
         jae     0f
-        cmp     $0x4000,%eax        /* sanity check (low) */
+        cmp     $0x4000,%ecx        /* sanity check (low) */
         jae     1f
 0:
-        movzwl  0x413,%eax          /* use base memory size on failure */
-        shl     $10-4,%eax
+        movzwl  0x413,%ecx          /* use base memory size on failure */
+        shl     $10-4,%ecx
 1:
         /*
          * Compare the value in the BDA with the information from the
@@ -106,20 +106,20 @@ __start:
         cmp     $0x100,%edx         /* is the multiboot value too small? */
         jb      2f                  /* if so, do not use it */
         shl     $10-4,%edx
-        cmp     %eax,%edx           /* compare with BDA value */
-        cmovb   %edx,%eax           /* and use the smaller */
+        cmp     %ecx,%edx           /* compare with BDA value */
+        cmovb   %edx,%ecx           /* and use the smaller */
 
 2:      /* Reserve 64kb for the trampoline */
-        sub     $0x1000,%eax
+        sub     $0x1000,%ecx
 
         /* From arch/x86/smpboot.c: start_eip had better be page-aligned! */
-        xor     %al, %al
-        shl     $4, %eax
-        mov     %eax,sym_phys(trampoline_phys)
+        xor     %cl, %cl
+        shl     $4, %ecx
+        mov     %ecx,sym_phys(trampoline_phys)
 
         /* Save the Multiboot info struct (after relocation) for later use. */
         mov     $sym_phys(cpu0_stack)+1024,%esp
-        push    %eax                /* Boot trampoline address. */
+        push    %ecx                /* Boot trampoline address. */
         push    %ebx                /* Multiboot information address. */
         call    reloc
         add     $8,%esp             /* Remove reloc() args from stack. */
-- 
1.7.10.4


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.