[Xen-devel] [PATCH v4 19/24] arm/acpi: Configure SPI interrupt type and route to Dom0 dynamically

[Shannon Zhao <zhaoshenglong@xxxxxxxxxx>]

From: Shannon Zhao <shannon.zhao@xxxxxxxxxx>

Interrupt information is described in DSDT and is not available at the
time of booting. Check if the interrupt is permitted to access and set
the interrupt type, route it to guest dynamically only for SPI
and Dom0.

Signed-off-by: Parth Dixit <parth.dixit@xxxxxxxxxx>
Signed-off-by: Shannon Zhao <shannon.zhao@xxxxxxxxxx>
---
 xen/arch/arm/vgic.c | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/xen/arch/arm/vgic.c b/xen/arch/arm/vgic.c
index ee35683..902a16d 100644
--- a/xen/arch/arm/vgic.c
+++ b/xen/arch/arm/vgic.c
@@ -25,6 +25,8 @@
 #include <xen/irq.h>
 #include <xen/sched.h>
 #include <xen/perfc.h>
+#include <xen/iocap.h>
+#include <xen/acpi.h>
 
 #include <asm/current.h>
 
@@ -334,6 +336,8 @@ void vgic_disable_irqs(struct vcpu *v, uint32_t r, int n)
     }
 }
 
+#define VGIC_ICFG_MASK(intr) ( 1 << ( ( 2 * ( intr % 16 ) ) + 1 ) )
+
 void vgic_enable_irqs(struct vcpu *v, uint32_t r, int n)
 {
     const unsigned long mask = r;
@@ -342,9 +346,37 @@ void vgic_enable_irqs(struct vcpu *v, uint32_t r, int n)
     unsigned long flags;
     int i = 0;
     struct vcpu *v_target;
+#ifdef CONFIG_HAS_ACPI
+    struct domain *d = v->domain;
+    struct vgic_irq_rank *vr = vgic_get_rank(v, n);
+    uint32_t tr;
+    int ret;
+#endif
 
     while ( (i = find_next_bit(&mask, 32, i)) < 32 ) {
         irq = i + (32 * n);
+#ifdef CONFIG_HAS_ACPI
+        /* Set the irq type and route it to guest only for SPI and Dom0 */
+        if( irq_access_permitted(d, irq) && is_hardware_domain(d) &&
+            ( irq >= 32 ) && ( !acpi_disabled ) )
+        {
+            tr = vr->icfg[i >> 4];
+
+            if ( tr & VGIC_ICFG_MASK(i) )
+                ret = irq_set_spi_type(irq, IRQ_TYPE_EDGE_BOTH);
+            else
+                ret = irq_set_spi_type(irq, IRQ_TYPE_LEVEL_MASK);
+            if ( ret )
+                printk(XENLOG_WARNING "The irq type is not correct\n");
+
+            vgic_reserve_virq(d, irq);
+
+            ret = route_irq_to_guest(d, irq, irq, NULL);
+            if ( ret )
+                printk(XENLOG_ERR "Unable to route IRQ %u to domain %u\n",
+                       irq, d->domain_id);
+        }
+#endif
         v_target = __vgic_get_target_vcpu(v, irq);
         p = irq_to_pending(v_target, irq);
         set_bit(GIC_IRQ_GUEST_ENABLED, &p->status);
-- 
2.0.4



_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel