Re: [Xen-devel] Multi-bridged PCIe devices (Was: Re: iommuu/vt-d issues with LSI MegaSAS (PERC5i))

[Konrad Rzeszutek Wilk <konrad.wilk@xxxxxxxxxx>]

> Which would look like this:
> 
> C220 ---> Tundra Bridge -----> (HB6 PCI bridge -> Brooktree BDFs) on the card
>             \--------------> IEEE-1394a
> 
> I am actually wondering if this 07:00.0 device is the one that
> reports itself as 08:00.0 (which I think is what you alluding to Jan)
> 

And to double check that theory I decided to pass in the IEEE-1394a to a guest:

           +-1c.5-[07-08]----00.0-[08]----03.0  Texas Instruments TSB43AB22A 
IEEE-1394a-2000 Controller (PHY/Link) [iOHCI-Lynx]


(XEN) [VT-D]iommu.c:885: iommu_fault_status: Fault Overflow
(XEN) [VT-D]iommu.c:887: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:865: DMAR:[DMA Read] Request device [0000:08:00.0] fault 
addr 370f1000, iommu reg = ffff82c3ffd53000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu ffff83083d4939b0 dev 0000:08:00.0 gmfn 370f1
(XEN)     root_entry = ffff83083d47f000
(XEN)     root_entry[8] = 72569b001
(XEN)     context = ffff83072569b000
(XEN)     context[0] = 0_0
(XEN)     ctxt_entry[0] not present

So, capture card OK - Likely the Tundra bridge has an issue:

07:00.0 PCI bridge: Tundra Semiconductor Corp. Device 8113 (rev 01) (prog-if 01 
[Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=07, secondary=08, subordinate=08, sec-latency=32
        Memory behind bridge: f0600000-f06fffff
        Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [60] Subsystem: Super Micro Computer Inc Device 0805
        Capabilities: [a0] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-


or there is some unknown bridge in the motherboard.

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel