Re: [Xen-devel] Windows 8 VGA Passthrough

[Gordan Bobic <gordan@xxxxxxxxxx>]

On 10/27/2013 02:27 PM, John Wargo wrote:
> On 10/27/2013 04:30 AM, Gordan Bobic wrote:
> > On 10/26/2013 09:58 PM, John Wargo wrote:
> > > Geniuses,
> > >
> > > I've been trying to get VGA pass-through working on Windows 8, however
> > > I've been running into a few issues.
> > > Currently I can get Windows 8 running flawlessly without VGA
> > > pass-through, however I'm planning on using it for gaming, so this wont
> > > work.
> > >
> > > When I start windows 8, I am able to get past the install portion of the
> > > DVD, however it hangs on "Getting devices ready.. (n%)".
> > >
> > > Hardware Information :
> > > AMD Fx6300
> > > ASUS M5a99x evo r2.0
> > > 16GB RAM
> > > 6670 Radeon HD - Dom0
> > > 7850 Radeon HD - Win8
> > I have recently (recently as in over the past 48 hours) re-tried to
> > get ATI VGA passthrough working, and the results are... interesting.
> >
> > HD4850 dom0 + HD7450 domU worked fine - or as fine as ATI passthrough
> > ever seems to work (slowdown + white lines when dragging windows after
> > a domU reboot). I am using XP64 domU so I can't eject the GPU (it says
> > it is being used). But shutting down the domU, doing echo 1 > reset
> > for the GPU from dom0 (I don't know how this is implemented and
> > whether it does anything) and then starting it up again sometimes
> > recovers it. GPU-Z runs and reports the GPU correctly.
> >
> > HD4850 dom0 + HD7970 domU results in the entire host locking up as
> > soon as the driver is loaded in domU. My solution is to swap the dom0
> > GPU for an 8800GT, and the problem now doesn't occur. If I had to
> > guess, BIOS on the HD7970 does something bizzare, finds the HD4850 on
> > the bus, tries to do something to it, and ends up crashing the host.
> > This could also be exacerbated by the fact that I have to run with
> > relaxed checking and no PCI ACS due to NF200 bridges on my
> > motherboard. Even so, however, GPU-Z crashes the domU and it's GPU
> > _hard_ (but not the host, thankfully). It crashes it so hard, that the
> > only cure is to reboot the host. Reseting the GPU via /sys/ doesn't
> > seem to do anything to help.
> >
> > Are you using gfx_passthru=1 in your config? The way most people have
> > this kind of thing working is with gfx_passthru=0, i.e. secondary
> > passthru. Don't assign the PCI device in the config when installing.
> > Once the domU install is complete, shut it down, and add the GPU you
> > want to pass through. Then fire up domU in VNC, install the driver,
> > and with a bit of luck it will come up with output on the external
> > monitor.
> >
> > Also make sure that radeon or radeonfb kernel drivers DO NOT load
> > before the device is assigned to xen-pciback. The exact way to ensure
> > this will depend on what distro and dom0 kernel you are using.
> >
> > Gordan
> Status update:
>
> The catalyst drivers appear to be working perfectly fine, device manager
> shows no errors, and everything works great, except that when I plug my
> monitor into the second card, I get "No Signal" on the monitor, then it
> shuts off.
>
> I though that secondary passthrough meant that it would pass the virtual
> adapter in as primary, but I could use my GPU that I passed through, so
> where am I wrong, and how do I do that?
Your understanding is correct - real VGA card will be passed as 
secondary, and the driver, when it loads, should start it up, and this 
normally takes over from the primary.
Two things come to mind:
1) I find that sometimes I have to disable the primary emulated VGA adapter.
2) Make sure your desktop settings are correctly set up to use the real 
VGA card as the primary desktop.
Gordan

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel