Re: [Xen-devel] current xen/stable 2.6.32.9 failed upgrade from 2.6.31.6

[Pasi Kärkkäinen <pasik@xxxxxx>]

On Fri, Mar 12, 2010 at 12:41:39PM +0100, Josip Rodin wrote:
> On Thu, Mar 11, 2010 at 09:24:56PM +0200, Pasi Kärkkäinen wrote:
> > > Sadly, it looks this iLO VSP is completely useless, because when I defined
> > > com1, the hypervisor started *not* displaying anything on the physical
> > > console or the virtual serial port.
> > > Maybe I'm missing something regarding the iLO VSP setup on this HP 
> > > DL380...
> > 
> > If you boot baremetal (non-Xen) Linux, on what IO-port and IRQ is the iLO
> > serial port?
> > 
> > Is it on the standard IO-port/IRQ, or some non-standard? In this case you
> > might have to specify the IOport on the xen cmdline options in grub.conf.
> > 
> > See also:
> > http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00263709/c00263709.pdf
> 
> Oh, thanks, that was useful. The manual actually documents that VSP is on
> COM *2*, not 1, and despite my prior ample negative experience with the
> off-by-one in port numbering, and the fact I had even used ttyS1=COM2 on
> this exact machine, I managed to screw that one up. Sorry for the noise.
> 
> So, I managed to get GRUB, the hypervisor and dom0 to display messages on
> VSP. (No luck yet with BIOS POST, but that is irrelevant for now.)
> 
> I'll first paste the few odd bits of log from the *working* 2.6.31.6 dom0,
> just to set up a possible baseline:
> 

<snip>

> 
> Everything else seems normal, and indeed the machine has worked normally
> in this setup for a few months.
> 
> And now here goes the whole output preceding the 2.6.32 crash:
>

<snip>

> 
> [    0.000000] ACPI: PM-Timer IO Port: 0x908
> [    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> [    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
> [    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] disabled)
> [    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
> [    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
> [    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
> [    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] disabled)
> [    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
> [    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
> [    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
> (XEN) mm.c:720:d0 Bad L1 flags 800000
> (XEN) mm.c:4221:d0 ptwr_emulate: could not get_page_from_l1e()
> (XEN) d0:v0: unhandled page fault (ec=0003)
> (XEN) Pagetable walk from ffff8800014fdfd8:
> (XEN)  L4[0x110] = 0000000115002067 0000000000001002
> (XEN)  L3[0x000] = 0000000115006067 0000000000001006
> (XEN)  L2[0x00a] = 0000000116c8a067 0000000000002c8a 
> (XEN)  L1[0x0fd] = 00100001154fd065 00000000000014fd
> (XEN) domain_crash_sync called from entry.S
> (XEN) Domain 0 (vcpu#0) crashed on cpu#0:
> (XEN) ----[ Xen-3.4  x86_64  debug=n  Not tainted ]----
> (XEN) CPU:    0
> (XEN) RIP:    e033:[<ffffffff8100d9df>]
> (XEN) RFLAGS: 0000000000000246   EM: 1   CONTEXT: pv guest
> (XEN) rax: 0000000000000000   rbx: 80000001154fc163   rcx: 00000000014fd000
> (XEN) rdx: 0000000000000000   rsi: 80000001154fc163   rdi: ffff8800014fdfd8
> (XEN) rbp: ffff8800014fdfd8   rsp: ffffffff813abd70   r8:  0000000000000002
> (XEN) r9:  ffffffff8146a060   r10: ffffffff8100b6a3   r11: ffffffff8146a060
> (XEN) r12: 80000001154fc163   r13: 0000000000000000   r14: ffffffffff4002c2
> (XEN) r15: ffffffff8147cbb0   cr0: 000000008005003b   cr4: 00000000000006f0
> (XEN) cr3: 0000000115001000   cr2: ffff8800014fdfd8
> (XEN) ds: 0000   es: 0000   fs: 0000   gs: 0000   ss: e02b   cs: e033
> (XEN) Guest stack trace from rsp=ffffffff813abd70:
> (XEN)    00000000014fd000 ffffffff8146a060 0000000000000003 ffffffff8100d9df
> (XEN)    000000010000e030 0000000000010046 ffffffff813abdb8 000000000000e02b
> (XEN)    ffffffff8100d9df ffffffffff5fb000 ffffffffff5fb000 0000000000000804
> (XEN)    ffffffff81025db1 0000000115003067 80000001154fc163 ffffffff81001000
> (XEN)    80000001154fc163 0000000000000008 ffffffff81029e63 0000000000000000
> (XEN)    ffffffff8100c40d ffffffff813abe88 0000000000000000 0000000000000000
> (XEN)    ffffffff814816a0 ffffffff8147cbb0 ffffffffff40026c ffffffffff40026c
> (XEN)    0000000000000080 ffffffff81336a73 ffffffff8147cbdc 0000000000000001
> (XEN)    ffffffff814925aa 00000001813abf78 00000000000000c2 ffffffffff400200
> (XEN)    0000000000000000 0000000000000000 ffffffffffffffff ffffffff813abf78
> (XEN)    0000000000000000 0000000000000000 ffffffff8147d220 ffffffff813abf78
> (XEN)    0000000001580600 0000000020000000 ffffffff81477685 ffffffff8100db3d
> (XEN)    0000000002b7b600 00000000015fb000 0000000002b7b600 ffffffff8133b055
> (XEN)    ffffffff8133fb05 0000000000000000 0000000000000000 0000000000000000
> (XEN)    0000000000000000 0000000000000000 ffffffffffffffff ffffffff814a2090
> (XEN)    0000000000000000 0000000000000000 ffffffff8147297d 00000000015dadd4
> (XEN)    0000000000000000 ffffffff814a3fc0 ffffffff81001000 0000000000000000
> (XEN)    0000000000000000 0000000000000000 ffffffff81475686 0000000000000000
> (XEN)    0000000000000000 0000000000000000 0000000000000000 0000000000000000
> (XEN)    0000000000000000 0000000000000000 0000000000000000 0000000000000001
> (XEN) Domain 0 crashed: 'noreboot' set - not rebooting.
> 
> In the meantime there was another update to the stable branch, I'll go
> compile that...
> 

This is a known problem.. I see it also on my old 32bit testbox.
64bit dom0 kernel works for me.

Jeremy has some ideas about what might be causing this..

-- Pasi


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel