Xen project Mailing List

Re: [Xen-devel] pvops: AHCI problems with SB600

To: Konrad Rzeszutek Wilk <konrad.wilk@xxxxxxxxxx>

From: Patrick Scharrenberg <pittipatti@xxxxxx>

Date: Tue, 22 Sep 2009 11:00:23 +0200

Cc: Jeremy Fitzhardinge <jeremy@xxxxxxxx>, Xen-devel <xen-devel@xxxxxxxxxxxxxxxxxxx>

Delivery-date: Tue, 22 Sep 2009 02:02:12 -0700

List-id: Xen developer discussion <xen-devel.lists.xensource.com>

Konrad Rzeszutek Wilk wrote: > Ooooh. Can you give some more details on the hardware flavor? CPU? Memory? Its an AMD system on an ASUS M2A-VM mainboard with an Athlon 64 X2 CPU and 8GB of memory. > What happens if you use dom0_mem=max:512MB or pass in 'irqpoll' to the > Linux kernel? irqpoll does not change anything but the memory limit does the trick. The system then boots fine, I attached the dmesg log. Since the netconsole now also works, I assume some kind of IRQ problem which is strengthened by the fact, that the keyboard didn't work either (for scrolling and searching for problems) without the memory limit option. > OK. I need the kernel boot log to figure out what might be a potential > problem. > Let's try to get your netconsole working or your serial console? Does this > machine even have a serial port? Maybe you can use that to capture the kernel > output? I attached the bootlog with the 512 memory-limit enabled and the xen dmesg. Unfortunately I have to drive 200km to install a serial cable to the system. So if there is an IRQ problem would the serial console really help or would it suffer from the same irq problem?

[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.31 (root@brontus) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #2 SMP Sat Sep 19 15:53:55 CEST 2009 [ 0.000000] Command line: root=/dev/mapper/brontus-xen_root ro debug netconsole=4444@xxxxxxx/eth0,6666@xxxxxxx/00:12:1E:19:D0:BC loglevel=10 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] xen_release_chunk: looking at area pfn 20000-ddee0 [ 0.000000] xen_release_chunk: looking at area pfn ddf00-e0000 [ 0.000000] xen_release_chunk: looking at area pfn f0000-fec00 [ 0.000000] released 0 pages of unused memory [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: 0000000000000000 - 000000000009f000 (usable) [ 0.000000] Xen: 000000000009f000 - 0000000000100000 (reserved) [ 0.000000] Xen: 0000000000100000 - 0000000020000000 (usable) [ 0.000000] Xen: 00000000ddee0000 - 00000000ddee3000 (ACPI NVS) [ 0.000000] Xen: 00000000ddee3000 - 00000000ddef0000 (ACPI data) [ 0.000000] Xen: 00000000ddef0000 - 00000000ddf00000 (reserved) [ 0.000000] Xen: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] Xen: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] DMI 2.4 present. [ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it. [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] last_pfn = 0x20000 max_arch_pfn = 0x400000000 [ 0.000000] Scanning 0 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 000000000009f000 (usable) [ 0.000000] modified: 000000000009f000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 0000000020000000 (usable) [ 0.000000] modified: 00000000ddee0000 - 00000000ddee3000 (ACPI NVS) [ 0.000000] modified: 00000000ddee3000 - 00000000ddef0000 (ACPI data) [ 0.000000] modified: 00000000ddef0000 - 00000000ddf00000 (reserved) [ 0.000000] modified: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] modified: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] init_memory_mapping: 0000000000000000-0000000020000000 [ 0.000000] 0000000000 - 0020000000 page 4k [ 0.000000] kernel direct mapping tables up to 20000000 @ 100000-202000 [ 0.000000] RAMDISK: 0199a000 - 02054200 [ 0.000000] ACPI: RSDP 00000000000f8210 00024 (v02 ATI ) [ 0.000000] ACPI: XSDT 00000000ddee3100 00044 (v01 ATI ASUSACPI 42302E31 AWRD 00000000) [ 0.000000] ACPI: FACP 00000000ddee8500 000F4 (v03 ATI ASUSACPI 42302E31 AWRD 00000000) [ 0.000000] ACPI: DSDT 00000000ddee3280 05210 (v01 ATI ASUSACPI 00001000 MSFT 03000000) [ 0.000000] ACPI: FACS 00000000ddee0000 00040 [ 0.000000] ACPI: HPET 00000000ddee8740 00038 (v01 ATI ASUSACPI 42302E31 AWRD 00000098) [ 0.000000] ACPI: MCFG 00000000ddee87c0 0003C (v01 ATI ASUSACPI 42302E31 AWRD 00000000) [ 0.000000] ACPI: APIC 00000000ddee8640 00084 (v01 ATI ASUSACPI 42302E31 AWRD 00000000) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 0020000000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0002156000 - 000216b000] XEN PAGETABLES ==> [0002156000 - 000216b000] [ 0.000000] #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] [ 0.000000] #3 [0001000000 - 0001979274] TEXT DATA BSS ==> [0001000000 - 0001979274] [ 0.000000] #4 [000199a000 - 0002054200] RAMDISK ==> [000199a000 - 0002054200] [ 0.000000] #5 [0002055000 - 0002156000] XEN START INFO ==> [0002055000 - 0002156000] [ 0.000000] #6 [000197a000 - 000197a155] BRK ==> [000197a000 - 000197a155] [ 0.000000] #7 [0000100000 - 00001ea000] PGTABLE ==> [0000100000 - 00001ea000] [ 0.000000] found SMP MP-table at [ffff8800000f6560] f6560 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00100000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x00020000 [ 0.000000] On node 0 totalpages: 130959 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 237 pages reserved [ 0.000000] DMA zone: 3690 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 1736 pages used for memmap [ 0.000000] DMA32 zone: 125240 pages, LIFO batch:31 [ 0.000000] Detected use of extended apic ids on hypertransport bus [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8200 base: 0xfed00000 [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 24 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 20000000 (gap: 20000000:bdee0000) [ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1 [ 0.000000] PERCPU: Allocated 22 4k pages, static data 88032 bytes [ 0.000000] trying to map vcpu_info 0 at ffffc9000000b020, mfn 21617f, offset 32 [ 0.000000] cpu 0 using vcpu_info at ffffc9000000b020 [ 0.000000] trying to map vcpu_info 1 at ffffc90000023020, mfn 216195, offset 32 [ 0.000000] cpu 1 using vcpu_info at ffffc90000023020 [ 0.000000] Xen: using vcpu_info placement [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 128930 [ 0.000000] Kernel command line: root=/dev/mapper/brontus-xen_root ro debug netconsole=4444@xxxxxxx/eth0,6666@xxxxxxx/00:12:1E:19:D0:BC loglevel=10 [ 0.000000] PID hash table entries: 2048 (order: 11, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000] Initializing CPU#0 [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Node 0: aperture @ 20000000 size 32 MB [ 0.000000] Aperture too small (32 MB) than (64 MB) [ 0.000000] PCI-DMA: Using Xen software bounce buffering for IO (Xen-SWIOTLB) [ 0.000000] xen_swiotlb_fixup: buf=ffff880002c6c000 size=67108864 [ 0.000000] xen_swiotlb_fixup: buf=ffff880006ccc000 size=32768 [ 0.000000] Placing 64MB Xen software IO TLB between ffff880002c6c000 - ffff880006c6c000 [ 0.000000] Xen software IO TLB at phys 0x2c6c000 - 0x6c6c000 [ 0.000000] Memory: 430336k/524288k available (5097k kernel code, 452k absent, 92804k reserved, 2902k data, 568k init) [ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:424 [ 0.000000] xen: registering gsi 0 triggering 1 polarity 0 [ 0.000000] xen: --> irq=0 [ 0.000000] xen_set_ioapic_routing: irq 0 gsi 0 vector 0 ioapic 0 pin 0 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 1 triggering 1 polarity 0 [ 0.000000] xen: --> irq=1 [ 0.000000] xen_set_ioapic_routing: irq 1 gsi 1 vector 1 ioapic 0 pin 1 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 3 triggering 1 polarity 0 [ 0.000000] xen: --> irq=3 [ 0.000000] xen_set_ioapic_routing: irq 3 gsi 3 vector 3 ioapic 0 pin 3 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 4 triggering 1 polarity 0 [ 0.000000] xen: --> irq=4 [ 0.000000] xen_set_ioapic_routing: irq 4 gsi 4 vector 4 ioapic 0 pin 4 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 5 triggering 1 polarity 0 [ 0.000000] xen: --> irq=5 [ 0.000000] xen_set_ioapic_routing: irq 5 gsi 5 vector 5 ioapic 0 pin 5 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 6 triggering 1 polarity 0 [ 0.000000] xen: --> irq=6 [ 0.000000] xen_set_ioapic_routing: irq 6 gsi 6 vector 6 ioapic 0 pin 6 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 7 triggering 1 polarity 0 [ 0.000000] xen: --> irq=7 [ 0.000000] xen_set_ioapic_routing: irq 7 gsi 7 vector 7 ioapic 0 pin 7 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 8 triggering 1 polarity 0 [ 0.000000] xen: --> irq=8 [ 0.000000] xen_set_ioapic_routing: irq 8 gsi 8 vector 8 ioapic 0 pin 8 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 9 triggering 0 polarity 1 [ 0.000000] xen: --> irq=9 [ 0.000000] xen_set_ioapic_routing: irq 9 gsi 9 vector 9 ioapic 0 pin 9 triggering 1 polarity 1 [ 0.000000] xen: registering gsi 10 triggering 1 polarity 0 [ 0.000000] xen: --> irq=10 [ 0.000000] xen_set_ioapic_routing: irq 10 gsi 10 vector 10 ioapic 0 pin 10 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 11 triggering 1 polarity 0 [ 0.000000] xen: --> irq=11 [ 0.000000] xen_set_ioapic_routing: irq 11 gsi 11 vector 11 ioapic 0 pin 11 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 12 triggering 1 polarity 0 [ 0.000000] xen: --> irq=12 [ 0.000000] xen_set_ioapic_routing: irq 12 gsi 12 vector 12 ioapic 0 pin 12 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 13 triggering 1 polarity 0 [ 0.000000] xen: --> irq=13 [ 0.000000] xen_set_ioapic_routing: irq 13 gsi 13 vector 13 ioapic 0 pin 13 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 14 triggering 1 polarity 0 [ 0.000000] xen: --> irq=14 [ 0.000000] xen_set_ioapic_routing: irq 14 gsi 14 vector 14 ioapic 0 pin 14 triggering 0 polarity 0 [ 0.000000] xen: registering gsi 15 triggering 1 polarity 0 [ 0.000000] xen: --> irq=15 [ 0.000000] xen_set_ioapic_routing: irq 15 gsi 15 vector 15 ioapic 0 pin 15 triggering 0 polarity 0 [ 0.000000] Detected 2399.914 MHz processor. [ 0.000999] Console: colour VGA+ 80x25 [ 0.000999] console [tty0] enabled [ 0.000999] Xen: using vcpuop timer interface [ 0.000999] installing Xen timer for CPU 0 [ 0.000999] alloc irq_desc for 24 on node 0 [ 0.000999] alloc kstat_irqs on node 0 [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 4799.82 BogoMIPS (lpj=2399914) [ 0.000999] Security Framework initialized [ 0.000999] SELinux: Initializing. [ 0.000999] SELinux: Starting in permissive mode [ 0.000999] Mount-cache hash table entries: 256 [ 0.000999] Initializing cgroup subsys ns [ 0.000999] Initializing cgroup subsys cpuacct [ 0.000999] Initializing cgroup subsys freezer [ 0.000999] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.000999] CPU: L2 Cache: 512K (64 bytes/line) [ 0.001014] tseg: 00ddf00000 [ 0.001080] CPU: Physical Processor ID: 0 [ 0.001147] CPU: Processor Core ID: 0 [ 0.001218] mce: CPU supports 5 MCE banks [ 0.001313] Performance Counters: AMD PMU driver. [ 0.001408] ------------[ cut here ]------------ [ 0.001480] WARNING: at /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/arch/x86/xen/enlighten.c:714 xen_apic_write+0x15/0x17() [ 0.001586] Hardware name: System Product Name [ 0.001652] Modules linked in: [ 0.001745] Pid: 0, comm: swapper Not tainted 2.6.31 #2 [ 0.001812] Call Trace: [ 0.001882] [<ffffffff8100b361>] ? xen_apic_write+0x15/0x17 [ 0.001953] [<ffffffff8104d22b>] warn_slowpath_common+0x77/0xa4 [ 0.001999] [<ffffffff8104d267>] warn_slowpath_null+0xf/0x11 [ 0.001999] [<ffffffff8100b361>] xen_apic_write+0x15/0x17 [ 0.001999] [<ffffffff8101f09b>] perf_counters_lapic_init+0x2e/0x30 [ 0.001999] [<ffffffff817f113c>] init_hw_perf_counters+0x305/0x3a2 [ 0.001999] [<ffffffff8100f07f>] ? xen_restore_fl_direct_end+0x0/0x1 [ 0.001999] [<ffffffff810dc633>] ? kmem_cache_alloc+0x7b/0xdd [ 0.001999] [<ffffffff817f0e08>] identify_boot_cpu+0x3c/0x3e [ 0.001999] [<ffffffff817f0e13>] check_bugs+0x9/0x2d [ 0.001999] [<ffffffff817e856a>] start_kernel+0x3d7/0x3ec [ 0.001999] [<ffffffff817e7a9f>] x86_64_start_reservations+0xaa/0xae [ 0.001999] [<ffffffff817eb8c9>] xen_start_kernel+0x61e/0x625 [ 0.001999] ---[ end trace 4eaa2a86a8e2da22 ]--- [ 0.001999] ... version: 0 [ 0.001999] ... bit width: 48 [ 0.001999] ... generic counters: 4 [ 0.001999] ... value mask: 0000ffffffffffff [ 0.001999] ... max period: 00007fffffffffff [ 0.001999] ... fixed-purpose counters: 0 [ 0.001999] ... counter mask: 000000000000000f [ 0.001999] SMP alternatives: switching to UP code [ 0.002683] ACPI: Core revision 20090521 [ 0.011105] alloc irq_desc for 25 on node 0 [ 0.011176] alloc kstat_irqs on node 0 [ 0.011250] cpu 0 spinlock event irq 25 [ 0.011319] alloc irq_desc for 26 on node 0 [ 0.011385] alloc kstat_irqs on node 0 [ 0.011455] alloc irq_desc for 27 on node 0 [ 0.011522] alloc kstat_irqs on node 0 [ 0.011592] alloc irq_desc for 28 on node 0 [ 0.011659] alloc kstat_irqs on node 0 [ 0.011731] alloc irq_desc for 29 on node 0 [ 0.011798] alloc kstat_irqs on node 0 [ 0.012061] installing Xen timer for CPU 1 [ 0.012130] alloc irq_desc for 30 on node 0 [ 0.012196] alloc kstat_irqs on node 0 [ 0.012268] alloc irq_desc for 31 on node 0 [ 0.012335] alloc kstat_irqs on node 0 [ 0.012406] cpu 1 spinlock event irq 31 [ 0.012502] SMP alternatives: switching to SMP code [ 0.012998] alloc irq_desc for 32 on node 0 [ 0.012998] alloc kstat_irqs on node 0 [ 0.013015] alloc irq_desc for 33 on node 0 [ 0.013081] alloc kstat_irqs on node 0 [ 0.013152] alloc irq_desc for 34 on node 0 [ 0.013218] alloc kstat_irqs on node 0 [ 0.013287] alloc irq_desc for 35 on node 0 [ 0.013353] alloc kstat_irqs on node 0 [ 0.000018] Initializing CPU#1 [ 0.000082] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.000086] CPU: L2 Cache: 512K (64 bytes/line) [ 0.000090] CPU: Physical Processor ID: 0 [ 0.000092] CPU: Processor Core ID: 1 [ 0.000100] mce: CPU supports 5 MCE banks [ 0.013592] Brought up 2 CPUs [ 0.014692] Booting paravirtualized kernel on Xen [ 0.014692] Xen version: 3.5-unstable (preserve-AD) (dom0) [ 0.015050] Grant table initialized [ 0.015150] Time: 8:51:59 Date: 09/22/09 [ 0.015301] NET: Registered protocol family 16 [ 0.015420] alloc irq_desc for 36 on node 0 [ 0.015420] alloc kstat_irqs on node 0 [ 0.016038] xenbus_probe_init ok [ 0.016299] node 0 link 0: io port [c000, ffff] [ 0.016372] TOM: 00000000e0000000 aka 3584M [ 0.016440] node 0 link 0: mmio [a0000, bffff] [ 0.016537] node 0 link 0: mmio [e0000000, dfffffff] [ 0.016633] node 0 link 0: mmio [f0000000, fe02ffff] [ 0.016728] node 0 link 0: mmio [e0000000, e03fffff] [ 0.017022] TOM2: 0000000220000000 aka 8704M [ 0.017089] bus: [00,03] on node 0 link 0 [ 0.017156] bus: 00 index 0 io port: [0, ffff] [ 0.017222] bus: 00 index 1 mmio: [a0000, bffff] [ 0.017289] bus: 00 index 2 mmio: [e0000000, efffffff] [ 0.017356] bus: 00 index 3 mmio: [f0000000, ffffffff] [ 0.017423] bus: 00 index 4 mmio: [220000000, fcffffffff] [ 0.017513] ACPI: bus type pci registered [ 0.017615] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.017615] PCI: MCFG area at e0000000 reserved in E820 [ 0.086288] PCI: Using MMCONFIG at e0000000 - efffffff [ 0.086363] PCI: Using configuration type 1 for base access [ 0.100119] bio: create slab <bio-0> at 0 [ 0.102149] ACPI: EC: Look up EC in DSDT [ 0.114184] ACPI: Interpreter enabled [ 0.114254] ACPI: (supports S0 S1 S3 S4 S5) [ 0.114501] ACPI: Using IOAPIC for interrupt routing [ 0.125358] ACPI: No dock devices found. [ 0.125606] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.126089] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold [ 0.126160] pci 0000:00:07.0: PME# disabled [ 0.126336] pci 0000:00:12.0: reg 10 io port: [0xff00-0xff07] [ 0.126413] pci 0000:00:12.0: reg 14 io port: [0xfe00-0xfe03] [ 0.126490] pci 0000:00:12.0: reg 18 io port: [0xfd00-0xfd07] [ 0.126568] pci 0000:00:12.0: reg 1c io port: [0xfc00-0xfc03] [ 0.126645] pci 0000:00:12.0: reg 20 io port: [0xfb00-0xfb0f] [ 0.126723] pci 0000:00:12.0: reg 24 32bit mmio: [0xfe02f000-0xfe02f3ff] [ 0.126886] pci 0000:00:13.0: reg 10 32bit mmio: [0xfe02e000-0xfe02efff] [ 0.127021] pci 0000:00:13.1: reg 10 32bit mmio: [0xfe02d000-0xfe02dfff] [ 0.127199] pci 0000:00:13.2: reg 10 32bit mmio: [0xfe02c000-0xfe02cfff] [ 0.127378] pci 0000:00:13.3: reg 10 32bit mmio: [0xfe02b000-0xfe02bfff] [ 0.127557] pci 0000:00:13.4: reg 10 32bit mmio: [0xfe02a000-0xfe02afff] [ 0.127772] pci 0000:00:13.5: reg 10 32bit mmio: [0xfe029000-0xfe0290ff] [ 0.127945] pci 0000:00:13.5: supports D1 D2 [ 0.127980] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot [ 0.127980] pci 0000:00:13.5: PME# disabled [ 0.128057] pci 0000:00:14.0: reg 10 io port: [0xb00-0xb0f] [ 0.128262] pci 0000:00:14.1: reg 10 io port: [0x00-0x07] [ 0.128340] pci 0000:00:14.1: reg 14 io port: [0x00-0x03] [ 0.128416] pci 0000:00:14.1: reg 18 io port: [0x00-0x07] [ 0.128493] pci 0000:00:14.1: reg 1c io port: [0x00-0x03] [ 0.128569] pci 0000:00:14.1: reg 20 io port: [0xf900-0xf90f] [ 0.129249] pci 0000:01:05.0: reg 10 64bit mmio: [0xfa000000-0xfbffffff] [ 0.129335] pci 0000:01:05.0: reg 18 64bit mmio: [0xfdbf0000-0xfdbfffff] [ 0.129412] pci 0000:01:05.0: reg 20 io port: [0xde00-0xdeff] [ 0.129488] pci 0000:01:05.0: reg 24 32bit mmio: [0xfda00000-0xfdafffff] [ 0.129595] pci 0000:01:05.0: supports D1 D2 [ 0.129739] pci 0000:00:01.0: bridge io port: [0xd000-0xdfff] [ 0.129813] pci 0000:00:01.0: bridge 32bit mmio: [0xfda00000-0xfdbfffff] [ 0.129891] pci 0000:00:01.0: bridge 64bit mmio pref: [0xfa000000-0xfbffffff] [ 0.129980] pci 0000:02:00.0: reg 10 io port: [0xee00-0xeeff] [ 0.129980] pci 0000:02:00.0: reg 18 64bit mmio: [0xfdfff000-0xfdffffff] [ 0.129980] pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x01ffff] [ 0.129980] pci 0000:02:00.0: supports D1 D2 [ 0.129980] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold [ 0.129980] pci 0000:02:00.0: PME# disabled [ 0.130088] pci 0000:00:07.0: bridge io port: [0xe000-0xefff] [ 0.130159] pci 0000:00:07.0: bridge 32bit mmio: [0xfdf00000-0xfdffffff] [ 0.130233] pci 0000:00:07.0: bridge 64bit mmio pref: [0xfdc00000-0xfdcfffff] [ 0.130423] pci 0000:00:14.4: transparent bridge [ 0.130495] pci 0000:00:14.4: bridge io port: [0xc000-0xcfff] [ 0.130567] pci 0000:00:14.4: bridge 32bit mmio: [0xfde00000-0xfdefffff] [ 0.130639] pci 0000:00:14.4: bridge 32bit mmio pref: [0xfdd00000-0xfddfffff] [ 0.130733] pci_bus 0000:00: on NUMA node 0 [ 0.130804] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.131395] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] [ 0.131745] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT] [ 0.131914] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [ 0.173113] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.173657] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.174103] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.175102] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.175644] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.176102] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.176643] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11) [ 0.177073] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.177572] xenbus_probe_backend_init bus registered ok [ 0.177572] xenbus_probe_frontend_init bus registered ok [ 0.177572] xen_balloon: Initialising balloon driver. [ 0.178140] SCSI subsystem initialized [ 0.178140] libata version 3.00 loaded. [ 0.179053] usbcore: registered new interface driver usbfs [ 0.179116] usbcore: registered new interface driver hub [ 0.179116] usbcore: registered new device driver usb [ 0.180182] PCI: Using ACPI for IRQ routing [ 0.180446] IO APIC resources couldn't be allocated. [ 0.194046] cfg80211: Using static regulatory domain info [ 0.194058] cfg80211: Regulatory domain: US [ 0.194124] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.194232] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 0.194305] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.194376] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.194446] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.194516] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.194586] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 0.194667] cfg80211: Calling CRDA for country: US [ 0.194772] NetLabel: Initializing [ 0.194772] NetLabel: domain hash size = 128 [ 0.194772] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.194772] NetLabel: unlabeled traffic allowed by default [ 0.195983] Switched to high resolution mode on CPU 0 [ 0.196210] Switched to high resolution mode on CPU 1 [ 0.202027] pnp: PnP ACPI init [ 0.202119] ACPI: bus type pnp registered [ 0.203617] xen: registering gsi 8 triggering 1 polarity 0 [ 0.203686] xen_allocate_pirq: returning irq 8 for gsi 8 [ 0.203752] xen: --> irq=8 [ 0.203819] xen_set_ioapic_routing: irq 8 gsi 8 vector 8 ioapic 0 pin 8 triggering 0 polarity 0 [ 0.204403] xen: registering gsi 13 triggering 1 polarity 0 [ 0.204472] xen_allocate_pirq: returning irq 13 for gsi 13 [ 0.204539] xen: --> irq=13 [ 0.204605] xen_set_ioapic_routing: irq 13 gsi 13 vector 13 ioapic 0 pin 13 triggering 0 polarity 0 [ 0.207199] pnp: PnP ACPI: found 10 devices [ 0.207268] ACPI: ACPI bus type pnp unregistered [ 0.207351] system 00:01: ioport range 0x4100-0x411f has been reserved [ 0.207419] system 00:01: ioport range 0x228-0x22f has been reserved [ 0.207486] system 00:01: ioport range 0x40b-0x40b has been reserved [ 0.207553] system 00:01: ioport range 0x4d6-0x4d6 has been reserved [ 0.207621] system 00:01: ioport range 0xc00-0xc01 has been reserved [ 0.207688] system 00:01: ioport range 0xc14-0xc14 has been reserved [ 0.207755] system 00:01: ioport range 0xc50-0xc52 has been reserved [ 0.207823] system 00:01: ioport range 0xc6c-0xc6d has been reserved [ 0.207890] system 00:01: ioport range 0xc6f-0xc6f has been reserved [ 0.207958] system 00:01: ioport range 0xcd0-0xcd1 has been reserved [ 0.208026] system 00:01: ioport range 0xcd2-0xcd3 has been reserved [ 0.208093] system 00:01: ioport range 0xcd4-0xcdf has been reserved [ 0.208160] system 00:01: ioport range 0x4000-0x40fe has been reserved [ 0.208172] system 00:01: ioport range 0x4210-0x4217 has been reserved [ 0.208172] system 00:01: ioport range 0xb10-0xb1f has been reserved [ 0.208172] system 00:07: ioport range 0x4d0-0x4d1 has been reserved [ 0.208172] system 00:07: ioport range 0x220-0x225 has been reserved [ 0.208172] system 00:08: iomem range 0xe0000000-0xefffffff has been reserved [ 0.208172] system 00:09: iomem range 0xcd600-0xcffff could not be reserved [ 0.208172] system 00:09: iomem range 0xf0000-0xf7fff could not be reserved [ 0.208172] system 00:09: iomem range 0xf8000-0xfbfff could not be reserved [ 0.208172] system 00:09: iomem range 0xfc000-0xfffff could not be reserved [ 0.208172] system 00:09: iomem range 0xddef0000-0xddfeffff could not be reserved [ 0.208172] system 00:09: iomem range 0xfed00000-0xfed000ff has been reserved [ 0.208172] system 00:09: iomem range 0xddee0000-0xddefffff could not be reserved [ 0.208172] system 00:09: iomem range 0xffff0000-0xffffffff has been reserved [ 0.208172] system 00:09: iomem range 0x0-0x9ffff could not be reserved [ 0.208172] system 00:09: iomem range 0x100000-0xddedffff could not be reserved [ 0.208172] system 00:09: iomem range 0xddff0000-0xdffeffff has been reserved [ 0.208172] system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved [ 0.208172] system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.208172] system 00:09: iomem range 0xfff80000-0xfffeffff has been reserved [ 0.215470] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 [ 0.215541] pci 0000:00:01.0: IO window: 0xd000-0xdfff [ 0.215612] pci 0000:00:01.0: MEM window: 0xfda00000-0xfdbfffff [ 0.215683] pci 0000:00:01.0: PREFETCH window: 0x000000fa000000-0x000000fbffffff [ 0.215797] pci 0000:00:07.0: PCI bridge, secondary bus 0000:02 [ 0.215866] pci 0000:00:07.0: IO window: 0xe000-0xefff [ 0.215937] pci 0000:00:07.0: MEM window: 0xfdf00000-0xfdffffff [ 0.216002] pci 0000:00:07.0: PREFETCH window: 0x000000fdc00000-0x000000fdcfffff [ 0.216002] pci 0000:00:14.4: PCI bridge, secondary bus 0000:03 [ 0.216002] pci 0000:00:14.4: IO window: 0xc000-0xcfff [ 0.216002] pci 0000:00:14.4: MEM window: 0xfde00000-0xfdefffff [ 0.216002] pci 0000:00:14.4: PREFETCH window: 0xfdd00000-0xfddfffff [ 0.216002] pci 0000:00:07.0: setting latency timer to 64 [ 0.216002] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.216002] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] [ 0.216002] pci_bus 0000:01: resource 0 io: [0xd000-0xdfff] [ 0.216002] pci_bus 0000:01: resource 1 mem: [0xfda00000-0xfdbfffff] [ 0.216002] pci_bus 0000:01: resource 2 pref mem [0xfa000000-0xfbffffff] [ 0.216002] pci_bus 0000:02: resource 0 io: [0xe000-0xefff] [ 0.216002] pci_bus 0000:02: resource 1 mem: [0xfdf00000-0xfdffffff] [ 0.216002] pci_bus 0000:02: resource 2 pref mem [0xfdc00000-0xfdcfffff] [ 0.216002] pci_bus 0000:03: resource 0 io: [0xc000-0xcfff] [ 0.216002] pci_bus 0000:03: resource 1 mem: [0xfde00000-0xfdefffff] [ 0.216002] pci_bus 0000:03: resource 2 pref mem [0xfdd00000-0xfddfffff] [ 0.216002] pci_bus 0000:03: resource 3 io: [0x00-0xffff] [ 0.216002] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff] [ 0.217435] NET: Registered protocol family 2 [ 0.217636] IP route cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.218227] TCP established hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.218758] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.219365] TCP: Hash tables configured (established 65536 bind 65536) [ 0.219439] TCP reno registered [ 0.219662] NET: Registered protocol family 1 [ 0.219824] Trying to unpack rootfs image as initramfs... [ 0.230681] Freeing initrd memory: 6888k freed [ 0.237071] Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba [ 0.237185] Scanning for low memory corruption every 60 seconds [ 0.237776] audit: initializing netlink socket (disabled) [ 0.237864] type=2000 audit(1253609519.993:1): initialized [ 0.245445] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.251181] VFS: Disk quotas dquot_6.5.2 [ 0.251435] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.254044] msgmni has been set to 855 [ 0.254411] SELinux: Registering netfilter hooks [ 0.255264] alg: No test for stdrng (krng) [ 0.255568] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.255674] io scheduler noop registered [ 0.255740] io scheduler anticipatory registered [ 0.255807] io scheduler deadline registered [ 0.255886] io scheduler cfq registered (default) [ 0.472067] pci 0000:01:05.0: Boot video device [ 0.472476] alloc irq_desc for 37 on node 0 [ 0.472543] alloc kstat_irqs on node 0 [ 0.472639] pcieport-driver 0000:00:07.0: setting latency timer to 64 [ 0.473127] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.473758] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.473866] ACPI: Power Button [PWRF] [ 0.474094] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 0.474200] ACPI: Power Button [PWRB] [ 0.474490] fan PNP0C0B:00: registered as cooling_device0 [ 0.474566] ACPI: Fan [FAN] (on) [ 0.475022] processor LNXCPU:00: registered as cooling_device1 [ 0.475243] processor LNXCPU:01: registered as cooling_device2 [ 0.475451] processor LNXCPU:02: registered as cooling_device3 [ 0.475658] processor LNXCPU:03: registered as cooling_device4 [ 0.479944] ACPI Warning: \_TZ_.THRM._PSL: Return Package type mismatch at index 0 - found [NULL Object Descriptor], expected Reference 20090521 nspredef-946 [ 0.480003] ACPI: Expecting a [Reference] package element, found type 0 [ 0.480003] ACPI: Invalid passive threshold [ 0.480721] thermal LNXTHERM:01: registered as thermal_zone0 [ 0.480809] ACPI: Thermal Zone [THRM] (40 C) [ 0.481131] Event-channel device installed. [ 0.485298] registering netback [ 0.492220] alloc irq_desc for 38 on node 0 [ 0.492293] alloc kstat_irqs on node 0 [ 0.493427] hpet_acpi_add: no address or irqs in _CRS [ 0.493686] Non-volatile memory driver v1.3 [ 0.493955] Linux agpgart interface v0.103 [ 0.494281] [drm] Initialized drm 1.1.0 20060810 [ 0.494508] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.499373] brd: module loaded [ 0.501396] loop: module loaded [ 0.501689] input: Macintosh mouse button emulation as /devices/virtual/input/input2 [ 0.502407] ahci 0000:00:12.0: version 3.0 [ 0.502495] xen: registering gsi 22 triggering 0 polarity 1 [ 0.502565] alloc irq_desc for 22 on node 0 [ 0.503349] alloc kstat_irqs on node 0 [ 0.505513] xen: --> irq=22 [ 0.505580] xen_set_ioapic_routing: irq 22 gsi 22 vector 22 ioapic 0 pin 22 triggering 1 polarity 1 [ 0.505696] ahci 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 0.505885] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 0.505992] ahci 0000:00:12.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part [ 0.506973] scsi0 : ahci [ 0.507523] scsi1 : ahci [ 0.507822] scsi2 : ahci [ 0.508132] scsi3 : ahci [ 0.508634] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22 [ 0.508745] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22 [ 0.508856] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22 [ 0.508965] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22 [ 0.509326] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 0.509421] xen: registering gsi 19 triggering 0 polarity 1 [ 0.509495] alloc irq_desc for 19 on node 0 [ 0.509564] alloc kstat_irqs on node 0 [ 0.509635] xen: --> irq=19 [ 0.509704] xen_set_ioapic_routing: irq 19 gsi 19 vector 19 ioapic 0 pin 19 triggering 1 polarity 1 [ 0.509824] r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.509964] r8169 0000:02:00.0: setting latency timer to 64 [ 0.510100] alloc irq_desc for 39 on node 0 [ 0.510100] alloc kstat_irqs on node 0 [ 0.510834] eth0: RTL8168b/8111b at 0xffffc9000007e000, 00:1b:fc:86:73:27, XID 38000000 IRQ 39 [ 0.512532] netconsole: local port 4444 [ 0.512600] netconsole: local IP 1.2.3.4 [ 0.512666] netconsole: interface eth0 [ 0.512732] netconsole: remote port 6666 [ 0.512798] netconsole: remote IP 1.2.3.5 [ 0.512864] netconsole: remote ethernet address 00:12:1e:19:d0:bc [ 0.512932] netconsole: device eth0 not up yet, forcing it [ 0.513449] r8169: eth0: link down [ 0.513637] r8169: eth0: link down [ 0.814306] ata2: SATA link down (SStatus 0 SControl 300) [ 0.966026] ata1: softreset failed (device not ready) [ 0.966095] ata1: applying SB600 PMP SRST workaround and retrying [ 0.967268] ata3: softreset failed (device not ready) [ 0.967336] ata3: applying SB600 PMP SRST workaround and retrying [ 0.968269] ata4: softreset failed (device not ready) [ 0.968337] ata4: applying SB600 PMP SRST workaround and retrying [ 1.119035] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.120278] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.121280] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.148058] ata1.00: ATA-8: ST3500320NS, SN06, max UDMA/133 [ 1.148129] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32) [ 1.148211] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1.149321] ata3.00: ATA-8: ST3500320NS, SN06, max UDMA/133 [ 1.149389] ata3.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32) [ 1.149470] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1.150260] ata4.00: ATA-8: ST3500320NS, SN06, max UDMA/133 [ 1.150327] ata4.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32) [ 1.150408] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1.190547] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1.190616] ata1.00: configured for UDMA/133 [ 1.191801] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1.191870] ata3.00: configured for UDMA/133 [ 1.192677] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd [ 1.192745] ata4.00: configured for UDMA/133 [ 1.201164] scsi 0:0:0:0: Direct-Access ATA ST3500320NS SN06 PQ: 0 ANSI: 5 [ 1.201799] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 1.201866] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.202146] scsi 2:0:0:0: Direct-Access ATA ST3500320NS SN06 PQ: 0 ANSI: 5 [ 1.202149] sd 0:0:0:0: [sda] Write Protect is off [ 1.202155] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.202211] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.202485] sda: [ 1.202913] sd 2:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 1.203185] sd 2:0:0:0: [sdb] Write Protect is off [ 1.203255] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1.203382] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.203755] sdb: [ 1.203994] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 1.204355] scsi 3:0:0:0: Direct-Access ATA ST3500320NS SN06 PQ: 0 ANSI: 5 [ 1.204879] sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 1.205091] sd 3:0:0:0: [sdc] Write Protect is off [ 1.205159] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 1.205313] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.205660] sdc: [ 1.205918] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 1.216527] sda1 sda4 [ 1.217357] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.219995] sdb1 sdb4 [ 1.220772] sd 2:0:0:0: [sdb] Attached SCSI disk [ 1.223383] sdc1 sdc4 [ 1.224200] sd 3:0:0:0: [sdc] Attached SCSI disk [ 2.147642] r8169: eth0: link up [ 2.153019] console [netcon0] enabled [ 2.154004] netconsole: network logging started [ 2.207689] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.207767] ehci_hcd: block sizes: qh 192 qtd 96 itd 192 sitd 96 [ 2.207891] xen: registering gsi 19 triggering 0 polarity 1 [ 2.207963] xen_allocate_pirq: returning irq 19 for gsi 19 [ 2.208035] xen: --> irq=19 [ 2.208106] xen_set_ioapic_routing: irq 19 gsi 19 vector 19 ioapic 0 pin 19 triggering 1 polarity 1 [ 2.208227] ehci_hcd 0000:00:13.5: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 2.208328] ehci_hcd 0000:00:13.5: EHCI Host Controller [ 2.208454] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file 'devices' [ 2.208580] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001' [ 2.208817] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1 [ 2.208945] ehci_hcd 0000:00:13.5: reset hcs_params 0x10520a dbg=1 cc=5 pcc=2 ordered !ppc ports=10 [ 2.209059] ehci_hcd 0000:00:13.5: reset hcc_params a072 thresh 7 uframes 256/512/1024 [ 2.209240] ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround [ 2.209366] ehci_hcd 0000:00:13.5: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 2.209497] ehci_hcd 0000:00:13.5: debug port 1 [ 2.209581] ehci_hcd 0000:00:13.5: MWI active [ 2.209652] ehci_hcd 0000:00:13.5: supports USB remote wakeup [ 2.209754] ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000 [ 2.209805] ehci_hcd 0000:00:13.5: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 2.209805] ehci_hcd 0000:00:13.5: init command 010009 (park)=0 ithresh=1 period=256 RUN [ 2.216018] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00 [ 2.216162] usb usb1: default language 0x0409 [ 2.216253] usb usb1: udev 1, busnum 1, minor = 0 [ 2.216324] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.216395] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.216501] usb usb1: Product: EHCI Host Controller [ 2.216571] usb usb1: Manufacturer: Linux 2.6.31 ehci_hcd [ 2.216640] usb usb1: SerialNumber: 0000:00:13.5 [ 2.216781] usb usb1: uevent [ 2.216959] usb usb1: usb_probe_device [ 2.217032] usb usb1: configuration #1 chosen from 1 choice [ 2.217131] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 2.217233] usb 1-0:1.0: uevent [ 2.217394] hub 1-0:1.0: usb_probe_interface [ 2.217465] hub 1-0:1.0: usb_probe_interface - got id [ 2.217536] hub 1-0:1.0: USB hub found [ 2.217641] hub 1-0:1.0: 10 ports detected [ 2.217712] hub 1-0:1.0: standalone hub [ 2.217781] hub 1-0:1.0: no power switching (usb 1.0) [ 2.217850] hub 1-0:1.0: individual port over-current protection [ 2.217920] hub 1-0:1.0: power on to power good time: 20ms [ 2.218018] hub 1-0:1.0: local power source is good [ 2.218090] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 2.218245] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001' [ 2.218492] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.218563] ohci_hcd: block sizes: ed 80 td 96 [ 2.218671] xen: registering gsi 16 triggering 0 polarity 1 [ 2.218745] alloc irq_desc for 16 on node 0 [ 2.218815] alloc kstat_irqs on node 0 [ 2.218894] xen: --> irq=16 [ 2.218964] xen_set_ioapic_routing: irq 16 gsi 16 vector 16 ioapic 0 pin 16 triggering 1 polarity 1 [ 2.219081] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 2.219170] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 2.219276] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002' [ 2.219512] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 [ 2.219666] ohci_hcd 0000:00:13.0: created debug files [ 2.219739] ohci_hcd 0000:00:13.0: supports USB remote wakeup [ 2.219836] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000 [ 2.274046] ohci_hcd 0000:00:13.0: OHCI controller state [ 2.274119] ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers [ 2.274193] ohci_hcd 0000:00:13.0: control 0x283 RWC HCFS=operational CBSR=3 [ 2.274265] ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0 [ 2.274336] ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF [ 2.274408] ohci_hcd 0000:00:13.0: intrenable 0x8000001a MIE UE RD WDH [ 2.274486] ohci_hcd 0000:00:13.0: hcca frame #0005 [ 2.274557] ohci_hcd 0000:00:13.0: roothub.a 02000202 POTPGT=2 NPS NDP=2(2) [ 2.274628] ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000 [ 2.274700] ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE [ 2.274772] ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS [ 2.274845] ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00000100 PPS [ 2.274952] usb usb2: default language 0x0409 [ 2.275050] usb usb2: udev 1, busnum 2, minor = 128 [ 2.275121] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.275192] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.275300] usb usb2: Product: OHCI Host Controller [ 2.275370] usb usb2: Manufacturer: Linux 2.6.31 ohci_hcd [ 2.275439] usb usb2: SerialNumber: 0000:00:13.0 [ 2.275575] usb usb2: uevent [ 2.275739] usb usb2: usb_probe_device [ 2.275810] usb usb2: configuration #1 chosen from 1 choice [ 2.275896] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 2.275995] usb 2-0:1.0: uevent [ 2.276159] hub 2-0:1.0: usb_probe_interface [ 2.276230] hub 2-0:1.0: usb_probe_interface - got id [ 2.276300] hub 2-0:1.0: USB hub found [ 2.276408] hub 2-0:1.0: 2 ports detected [ 2.276479] hub 2-0:1.0: standalone hub [ 2.276548] hub 2-0:1.0: no power switching (usb 1.0) [ 2.276617] hub 2-0:1.0: global over-current protection [ 2.276686] hub 2-0:1.0: power on to power good time: 4ms [ 2.276775] hub 2-0:1.0: local power source is good [ 2.276844] hub 2-0:1.0: no over-current condition exists [ 2.276915] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 2.277031] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001' [ 2.277205] xen: registering gsi 17 triggering 0 polarity 1 [ 2.277280] alloc irq_desc for 17 on node 0 [ 2.277350] alloc kstat_irqs on node 0 [ 2.277429] xen: --> irq=17 [ 2.277499] xen_set_ioapic_routing: irq 17 gsi 17 vector 17 ioapic 0 pin 17 triggering 1 polarity 1 [ 2.277615] ohci_hcd 0000:00:13.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 2.277702] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 2.277786] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '003' [ 2.278034] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 [ 2.280993] ohci_hcd 0000:00:13.1: created debug files [ 2.281069] ohci_hcd 0000:00:13.1: supports USB remote wakeup [ 2.281164] ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000 [ 2.318029] ehci_hcd 0000:00:13.5: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT [ 2.318142] hub 1-0:1.0: port 1: status 0501 change 0001 [ 2.318229] ehci_hcd 0000:00:13.5: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT [ 2.318340] hub 1-0:1.0: port 2: status 0501 change 0001 [ 2.335045] ohci_hcd 0000:00:13.1: OHCI controller state [ 2.335118] ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers [ 2.335191] ohci_hcd 0000:00:13.1: control 0x283 RWC HCFS=operational CBSR=3 [ 2.335264] ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0 [ 2.335335] ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF [ 2.335405] ohci_hcd 0000:00:13.1: intrenable 0x8000001a MIE UE RD WDH [ 2.335483] ohci_hcd 0000:00:13.1: hcca frame #0005 [ 2.335553] ohci_hcd 0000:00:13.1: roothub.a 02000202 POTPGT=2 NPS NDP=2(2) [ 2.335624] ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000 [ 2.335695] ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE [ 2.335766] ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00000100 PPS [ 2.335838] ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS [ 2.335943] usb usb3: default language 0x0409 [ 2.336041] usb usb3: udev 1, busnum 3, minor = 256 [ 2.336111] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.336182] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.336292] usb usb3: Product: OHCI Host Controller [ 2.336365] usb usb3: Manufacturer: Linux 2.6.31 ohci_hcd [ 2.336436] usb usb3: SerialNumber: 0000:00:13.1 [ 2.336572] usb usb3: uevent [ 2.336736] usb usb3: usb_probe_device [ 2.336811] usb usb3: configuration #1 chosen from 1 choice [ 2.336900] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 2.337014] usb 3-0:1.0: uevent [ 2.337175] hub 3-0:1.0: usb_probe_interface [ 2.337249] hub 3-0:1.0: usb_probe_interface - got id [ 2.337325] hub 3-0:1.0: USB hub found [ 2.337440] hub 3-0:1.0: 2 ports detected [ 2.337513] hub 3-0:1.0: standalone hub [ 2.337585] hub 3-0:1.0: no power switching (usb 1.0) [ 2.337656] hub 3-0:1.0: global over-current protection [ 2.337727] hub 3-0:1.0: power on to power good time: 4ms [ 2.337818] hub 3-0:1.0: local power source is good [ 2.337892] hub 3-0:1.0: no over-current condition exists [ 2.337964] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 2.338083] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001' [ 2.338259] xen: registering gsi 18 triggering 0 polarity 1 [ 2.338335] alloc irq_desc for 18 on node 0 [ 2.338403] alloc kstat_irqs on node 0 [ 2.338483] xen: --> irq=18 [ 2.338552] xen_set_ioapic_routing: irq 18 gsi 18 vector 18 ioapic 0 pin 18 triggering 1 polarity 1 [ 2.338668] ohci_hcd 0000:00:13.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 2.338755] ohci_hcd 0000:00:13.2: OHCI Host Controller [ 2.338839] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '004' [ 2.339091] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4 [ 2.339251] ohci_hcd 0000:00:13.2: created debug files [ 2.339324] ohci_hcd 0000:00:13.2: supports USB remote wakeup [ 2.339420] ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000 [ 2.376052] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 2.394045] ohci_hcd 0000:00:13.2: OHCI controller state [ 2.394118] ohci_hcd 0000:00:13.2: OHCI 1.0, NO legacy support registers [ 2.394191] ohci_hcd 0000:00:13.2: control 0x283 RWC HCFS=operational CBSR=3 [ 2.394263] ohci_hcd 0000:00:13.2: cmdstatus 0x00000 SOC=0 [ 2.394334] ohci_hcd 0000:00:13.2: intrstatus 0x00000004 SF [ 2.394405] ohci_hcd 0000:00:13.2: intrenable 0x8000001a MIE UE RD WDH [ 2.394483] ohci_hcd 0000:00:13.2: hcca frame #0005 [ 2.394554] ohci_hcd 0000:00:13.2: roothub.a 02000202 POTPGT=2 NPS NDP=2(2) [ 2.394626] ohci_hcd 0000:00:13.2: roothub.b 00000000 PPCM=0000 DR=0000 [ 2.394697] ohci_hcd 0000:00:13.2: roothub.status 00008000 DRWE [ 2.394769] ohci_hcd 0000:00:13.2: roothub.portstatus [0] 0x00000100 PPS [ 2.394841] ohci_hcd 0000:00:13.2: roothub.portstatus [1] 0x00000100 PPS [ 2.394951] usb usb4: default language 0x0409 [ 2.395050] usb usb4: udev 1, busnum 4, minor = 384 [ 2.395122] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.395193] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.395301] usb usb4: Product: OHCI Host Controller [ 2.395370] usb usb4: Manufacturer: Linux 2.6.31 ohci_hcd [ 2.395439] usb usb4: SerialNumber: 0000:00:13.2 [ 2.395579] usb usb4: uevent [ 2.395737] usb usb4: usb_probe_device [ 2.395807] usb usb4: configuration #1 chosen from 1 choice [ 2.395893] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 2.395992] usb 4-0:1.0: uevent [ 2.396156] hub 4-0:1.0: usb_probe_interface [ 2.396226] hub 4-0:1.0: usb_probe_interface - got id [ 2.396297] hub 4-0:1.0: USB hub found [ 2.396401] hub 4-0:1.0: 2 ports detected [ 2.396472] hub 4-0:1.0: standalone hub [ 2.396542] hub 4-0:1.0: no power switching (usb 1.0) [ 2.396611] hub 4-0:1.0: global over-current protection [ 2.396681] hub 4-0:1.0: power on to power good time: 4ms [ 2.396767] hub 4-0:1.0: local power source is good [ 2.396836] hub 4-0:1.0: no over-current condition exists [ 2.396906] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 2.397026] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001' [ 2.397197] xen: registering gsi 17 triggering 0 polarity 1 [ 2.397269] xen_allocate_pirq: returning irq 17 for gsi 17 [ 2.397340] xen: --> irq=17 [ 2.397409] xen_set_ioapic_routing: irq 17 gsi 17 vector 17 ioapic 0 pin 17 triggering 1 polarity 1 [ 2.397529] ohci_hcd 0000:00:13.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 2.397615] ohci_hcd 0000:00:13.3: OHCI Host Controller [ 2.397700] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '005' [ 2.397938] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5 [ 2.398099] ohci_hcd 0000:00:13.3: created debug files [ 2.398171] ohci_hcd 0000:00:13.3: supports USB remote wakeup [ 2.398248] ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000 [ 2.418038] hub 1-0:1.0: state 7 ports 10 chg 0006 evt 0000 [ 2.418124] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 2.453047] ohci_hcd 0000:00:13.3: OHCI controller state [ 2.453122] ohci_hcd 0000:00:13.3: OHCI 1.0, NO legacy support registers [ 2.453194] ohci_hcd 0000:00:13.3: control 0x283 RWC HCFS=operational CBSR=3 [ 2.453266] ohci_hcd 0000:00:13.3: cmdstatus 0x00000 SOC=0 [ 2.453337] ohci_hcd 0000:00:13.3: intrstatus 0x00000004 SF [ 2.453409] ohci_hcd 0000:00:13.3: intrenable 0x8000001a MIE UE RD WDH [ 2.453487] ohci_hcd 0000:00:13.3: hcca frame #0005 [ 2.453559] ohci_hcd 0000:00:13.3: roothub.a 02000202 POTPGT=2 NPS NDP=2(2) [ 2.453630] ohci_hcd 0000:00:13.3: roothub.b 00000000 PPCM=0000 DR=0000 [ 2.453701] ohci_hcd 0000:00:13.3: roothub.status 00008000 DRWE [ 2.453774] ohci_hcd 0000:00:13.3: roothub.portstatus [0] 0x00000100 PPS [ 2.453846] ohci_hcd 0000:00:13.3: roothub.portstatus [1] 0x00000100 PPS [ 2.453951] usb usb5: default language 0x0409 [ 2.454075] usb usb5: udev 1, busnum 5, minor = 512 [ 2.454146] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.454217] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.454324] usb usb5: Product: OHCI Host Controller [ 2.454393] usb usb5: Manufacturer: Linux 2.6.31 ohci_hcd [ 2.454462] usb usb5: SerialNumber: 0000:00:13.3 [ 2.454599] usb usb5: uevent [ 2.454759] usb usb5: usb_probe_device [ 2.454830] usb usb5: configuration #1 chosen from 1 choice [ 2.454915] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 2.455024] usb 5-0:1.0: uevent [ 2.455181] hub 5-0:1.0: usb_probe_interface [ 2.455252] hub 5-0:1.0: usb_probe_interface - got id [ 2.455323] hub 5-0:1.0: USB hub found [ 2.455427] hub 5-0:1.0: 2 ports detected [ 2.455498] hub 5-0:1.0: standalone hub [ 2.455568] hub 5-0:1.0: no power switching (usb 1.0) [ 2.455637] hub 5-0:1.0: global over-current protection [ 2.455706] hub 5-0:1.0: power on to power good time: 4ms [ 2.455793] hub 5-0:1.0: local power source is good [ 2.455862] hub 5-0:1.0: no over-current condition exists [ 2.455932] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 2.456053] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001' [ 2.456222] xen: registering gsi 18 triggering 0 polarity 1 [ 2.456293] xen_allocate_pirq: returning irq 18 for gsi 18 [ 2.456363] xen: --> irq=18 [ 2.456432] xen_set_ioapic_routing: irq 18 gsi 18 vector 18 ioapic 0 pin 18 triggering 1 polarity 1 [ 2.456550] ohci_hcd 0000:00:13.4: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 2.456637] ohci_hcd 0000:00:13.4: OHCI Host Controller [ 2.456724] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '006' [ 2.456966] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6 [ 2.457127] ohci_hcd 0000:00:13.4: created debug files [ 2.457199] ohci_hcd 0000:00:13.4: supports USB remote wakeup [ 2.457277] ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000 [ 2.469285] ehci_hcd 0000:00:13.5: port 1 high speed [ 2.469360] ehci_hcd 0000:00:13.5: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT [ 2.512048] ohci_hcd 0000:00:13.4: OHCI controller state [ 2.512121] ohci_hcd 0000:00:13.4: OHCI 1.0, NO legacy support registers [ 2.512194] ohci_hcd 0000:00:13.4: control 0x283 RWC HCFS=operational CBSR=3 [ 2.512265] ohci_hcd 0000:00:13.4: cmdstatus 0x00000 SOC=0 [ 2.512337] ohci_hcd 0000:00:13.4: intrstatus 0x00000004 SF [ 2.512408] ohci_hcd 0000:00:13.4: intrenable 0x8000001a MIE UE RD WDH [ 2.512486] ohci_hcd 0000:00:13.4: hcca frame #0005 [ 2.513003] ohci_hcd 0000:00:13.4: roothub.a 02000202 POTPGT=2 NPS NDP=2(2) [ 2.513003] ohci_hcd 0000:00:13.4: roothub.b 00000000 PPCM=0000 DR=0000 [ 2.513003] ohci_hcd 0000:00:13.4: roothub.status 00008000 DRWE [ 2.513003] ohci_hcd 0000:00:13.4: roothub.portstatus [0] 0x00000100 PPS [ 2.513003] ohci_hcd 0000:00:13.4: roothub.portstatus [1] 0x00000100 PPS [ 2.515753] usb usb6: default language 0x0409 [ 2.515843] usb usb6: udev 1, busnum 6, minor = 640 [ 2.515912] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.515984] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.516091] usb usb6: Product: OHCI Host Controller [ 2.516160] usb usb6: Manufacturer: Linux 2.6.31 ohci_hcd [ 2.516230] usb usb6: SerialNumber: 0000:00:13.4 [ 2.516377] usb usb6: uevent [ 2.516537] usb usb6: usb_probe_device [ 2.516608] usb usb6: configuration #1 chosen from 1 choice [ 2.516693] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 2.516792] usb 6-0:1.0: uevent [ 2.516948] hub 6-0:1.0: usb_probe_interface [ 2.517019] hub 6-0:1.0: usb_probe_interface - got id [ 2.517089] hub 6-0:1.0: USB hub found [ 2.517201] hub 6-0:1.0: 2 ports detected [ 2.517273] hub 6-0:1.0: standalone hub [ 2.517343] hub 6-0:1.0: no power switching (usb 1.0) [ 2.517412] hub 6-0:1.0: global over-current protection [ 2.517481] hub 6-0:1.0: power on to power good time: 4ms [ 2.517569] hub 6-0:1.0: local power source is good [ 2.517638] hub 6-0:1.0: no over-current condition exists [ 2.517709] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 2.517815] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001' [ 2.518072] uhci_hcd: USB Universal Host Controller Interface driver [ 2.518548] usbcore: registered new interface driver usblp [ 2.518621] Initializing USB Mass Storage driver... [ 2.518801] usbcore: registered new interface driver usb-storage [ 2.518874] USB Mass Storage support registered. [ 2.519059] usbcore: registered new interface driver libusual [ 2.519508] PNP: No PS/2 controller found. Probing ports directly. [ 2.520155] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.520232] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.520291] usb 1-1: new high speed USB device using ehci_hcd and address 2 [ 2.520579] mice: PS/2 mouse device common for all mice [ 2.521250] rtc_cmos 00:04: RTC can wake from S4 [ 2.521460] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 [ 2.521580] rtc0: alarms up to one month, 242 bytes nvram [ 2.521896] it87: Found IT8716F chip at 0x228, revision 1 [ 2.521989] it87: in3 is VCC (+5V) [ 2.522062] it87: in7 is VCCH (+5V Stand-By) [ 2.522321] ACPI: I/O resource it87 [0x22d-0x22e] conflicts with ACPI region IP__ [0x22d-0x22e] [ 2.522434] ACPI: Device needs an ACPI driver [ 2.522617] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141 [ 2.522959] md: raid1 personality registered for level 1 [ 2.523504] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@xxxxxxxxxx [ 2.523857] cpuidle: using governor ladder [ 2.523930] cpuidle: using governor menu [ 2.526630] usbcore: registered new interface driver hiddev [ 2.526804] usbcore: registered new interface driver usbhid [ 2.526876] usbhid: v2.6:USB HID core driver [ 2.527177] Netfilter messages via NETLINK v0.30. [ 2.527282] nf_conntrack version 0.5.0 (4096 buckets, 16384 max) [ 2.527782] ctnetlink v0.93: registering with nfnetlink. [ 2.529421] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.529530] TCP cubic registered [ 2.529599] Initializing XFRM netlink socket [ 2.530174] NET: Registered protocol family 10 [ 2.533243] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2.533431] IPv6 over IPv4 tunneling driver [ 2.535164] NET: Registered protocol family 17 [ 2.535710] RPC: Registered udp transport module. [ 2.535781] RPC: Registered tcp transport module. [ 2.536254] PM: Resume from disk failed. [ 2.536367] registered taskstats version 1 [ 2.536602] Magic number: 9:856:877 [ 2.536915] Freeing unused kernel memory: 568k freed [ 2.537304] Write protecting the kernel read-only data: 7344k [ 2.571303] ehci_hcd 0000:00:13.5: port 1 high speed [ 2.571390] ehci_hcd 0000:00:13.5: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT [ 2.636518] usb 1-1: default language 0x0409 [ 2.638893] usb 1-1: udev 2, busnum 1, minor = 1 [ 2.638964] usb 1-1: New USB device found, idVendor=1005, idProduct=b113 [ 2.639038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.639114] usb 1-1: Product: USB FLASH DRIVE [ 2.639117] usb 1-1: Manufacturer: [ 2.639120] usb 1-1: SerialNumber: 1968050104CA [ 2.639231] usb 1-1: uevent [ 2.639532] usb 1-1: usb_probe_device [ 2.639607] usb 1-1: configuration #1 chosen from 1 choice [ 2.639897] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 2.640016] usb 1-1:1.0: uevent [ 2.640198] usb-storage 1-1:1.0: usb_probe_interface [ 2.640282] usb-storage 1-1:1.0: usb_probe_interface - got id [ 2.647884] scsi4 : SCSI emulation for USB Mass Storage devices [ 2.656535] usb-storage: device found at 2 [ 2.656582] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002' [ 2.656654] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 2.656821] usb-storage: waiting for device to settle before scanning [ 2.708046] ehci_hcd 0000:00:13.5: port 2 full speed --> companion [ 2.708137] ehci_hcd 0000:00:13.5: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT [ 2.708318] hub 1-0:1.0: port 2 not reset yet, waiting 50ms [ 2.760038] ehci_hcd 0000:00:13.5: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC [ 2.760224] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 2.760319] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 2.760408] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 2.760494] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 2.760570] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0004 [ 2.760657] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 2.760742] ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS [ 2.760873] hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s [ 2.861139] usb usb2: uevent [ 2.861175] usb 2-0:1.0: uevent [ 2.861277] usb usb3: uevent [ 2.861314] usb 3-0:1.0: uevent [ 2.861415] usb usb4: uevent [ 2.861450] usb 4-0:1.0: uevent [ 2.861549] usb usb5: uevent [ 2.861583] usb 5-0:1.0: uevent [ 2.861687] usb usb6: uevent [ 2.861722] usb 6-0:1.0: uevent [ 2.861822] usb usb1: uevent [ 2.861858] usb 1-0:1.0: uevent [ 2.861897] usb 1-1: uevent [ 2.861933] usb 1-1:1.0: uevent [ 2.864048] hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 [ 2.885134] ohci_hcd 0000:00:13.0: port[1] reset timeout, stat 00000111 [ 2.936150] ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS [ 2.987064] usb 2-2: new full speed USB device using ohci_hcd and address 2 [ 3.009070] ohci_hcd 0000:00:13.0: port[1] reset timeout, stat 00000113 [ 3.060049] ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS [ 3.130077] usb 2-2: skipped 1 descriptor after interface [ 3.130082] usb 2-2: skipped 1 descriptor after interface [ 3.134823] usb 2-2: default language 0x0409 [ 3.140083] usb 2-2: udev 2, busnum 2, minor = 129 [ 3.140164] usb 2-2: New USB device found, idVendor=14dd, idProduct=0002 [ 3.140246] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.140249] usb 2-2: Product: MultiDevice [ 3.140252] usb 2-2: Manufacturer: Peppercon AG [ 3.140255] usb 2-2: SerialNumber: 768E1175CA002E778E2336515C01B222 [ 3.140390] usb 2-2: uevent [ 3.140410] usb 2-2: usb_probe_device [ 3.140414] usb 2-2: configuration #1 chosen from 1 choice [ 3.142084] usb 2-2: adding 2-2:1.0 (config #1, interface 0) [ 3.142125] usb 2-2:1.0: uevent [ 3.142157] usbhid 2-2:1.0: usb_probe_interface [ 3.142161] usbhid 2-2:1.0: usb_probe_interface - got id [ 3.148471] input: Peppercon AG MultiDevice as /devices/pci0000:00/0000:00:13.0/usb2/2-2/2-2:1.0/input/input3 [ 3.148709] generic-usb 0003:14DD:0002.0001: input,hidraw0: USB HID v1.01 Keyboard [Peppercon AG MultiDevice] on usb-0000:00:13.0-2/input0 [ 3.148875] usb 2-2: adding 2-2:1.1 (config #1, interface 1) [ 3.148983] usb 2-2:1.1: uevent [ 3.149011] usbhid 2-2:1.1: usb_probe_interface [ 3.149116] usbhid 2-2:1.1: usb_probe_interface - got id [ 3.156179] input: Peppercon AG MultiDevice as /devices/pci0000:00/0000:00:13.0/usb2/2-2/2-2:1.1/input/input4 [ 3.156442] generic-usb 0003:14DD:0002.0002: input,hidraw1: USB HID v1.01 Mouse [Peppercon AG MultiDevice] on usb-0000:00:13.0-2/input1 [ 3.156600] /usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002' [ 3.156757] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 3.455023] ohci_hcd 0000:00:13.1: auto-stop root hub [ 3.455041] ohci_hcd 0000:00:13.2: auto-stop root hub [ 3.704027] ohci_hcd 0000:00:13.3: auto-stop root hub [ 3.704043] ohci_hcd 0000:00:13.4: auto-stop root hub [ 5.181123] md: md1 stopped. [ 5.192108] md: bind<sdb4> [ 5.192562] md: bind<sda4> [ 5.192995] md: bind<sdc4> [ 5.196365] raid1: raid set md1 active with 3 out of 3 mirrors [ 5.196482] md1: detected capacity change from 0 to 499586957312 [ 5.198531] md1: unknown partition table [ 5.705038] hub 4-0:1.0: hub_suspend [ 5.705127] usb usb4: bus auto-suspend [ 5.705202] ohci_hcd 0000:00:13.2: suspend root hub [ 5.705296] hub 5-0:1.0: hub_suspend [ 5.705373] usb usb5: bus auto-suspend [ 5.705447] ohci_hcd 0000:00:13.3: suspend root hub [ 5.705527] hub 6-0:1.0: hub_suspend [ 5.705604] usb usb6: bus auto-suspend [ 5.705678] ohci_hcd 0000:00:13.4: suspend root hub [ 5.706023] hub 3-0:1.0: hub_suspend [ 5.706101] usb usb3: bus auto-suspend [ 5.706174] ohci_hcd 0000:00:13.1: suspend root hub [ 7.657119] scsi 4:0:0:0: Direct-Access USB FLASH DRIVE 34CE PQ: 0 ANSI: 0 CCS [ 7.657361] sd 4:0:0:0: Attached scsi generic sg3 type 0 [ 7.658235] sd 4:0:0:0: [sdd] 2015232 512-byte logical blocks: (1.03 GB/984 MiB) [ 7.659030] usb-storage: device scan complete [ 7.659462] sd 4:0:0:0: [sdd] Write Protect is off [ 7.659467] sd 4:0:0:0: [sdd] Mode Sense: 23 00 00 00 [ 7.659471] sd 4:0:0:0: [sdd] Assuming drive cache: write through [ 7.662974] sd 4:0:0:0: [sdd] Assuming drive cache: write through [ 7.662980] sdd: sdd1 sdd2 sdd3 [ 7.665259] sd 4:0:0:0: [sdd] Assuming drive cache: write through [ 7.665263] sd 4:0:0:0: [sdd] Attached SCSI removable disk [ 12.131313] kjournald starting. Commit interval 5 seconds [ 12.131332] EXT3-fs: mounted filesystem with writeback data mode. [ 12.852010] eth0: no IPv6 routers present [ 13.381651] udevd version 125 started [ 13.517401] usb usb2: uevent [ 13.517438] usb 2-0:1.0: uevent [ 13.517480] usb 2-2: uevent [ 13.517539] usb 2-2:1.0: uevent [ 13.517788] usb 2-2:1.1: uevent [ 13.518236] usb usb3: uevent [ 13.518273] usb 3-0:1.0: uevent [ 13.518387] usb usb4: uevent [ 13.518424] usb 4-0:1.0: uevent [ 13.518550] usb usb5: uevent [ 13.518598] usb 5-0:1.0: uevent [ 13.518730] usb usb6: uevent [ 13.518767] usb 6-0:1.0: uevent [ 13.518886] usb usb1: uevent [ 13.518937] usb 1-0:1.0

__ __ _____ ____ _ _ _ \ \/ /___ _ __ |___ / | ___| _ _ _ __ ___| |_ __ _| |__ | | ___ \ // _ \ \047_ \ |_ \ |___ \ __| | | | \047_ \/ __| __/ _` | \047_ \| |/ _ \ / \ __/ | | | ___) | ___) |__| |_| | | | \__ \ || (_| | |_) | | __/ /_/\_\___|_| |_| |____(_)____/ \__,_|_| |_|___/\__\__,_|_.__/|_|\___| (XEN) Xen version 3.5-unstable (root@xxxxxxxxxxxxxxxx) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) Sat Sep 19 12:38:39 CEST 2009 (XEN) Latest ChangeSet: Fri Sep 18 14:45:40 2009 +0100 20228:3a71e070e3c5 (XEN) Command line: (XEN) Video information: (XEN) VGA is text mode 80x25, font 8x16 (XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds (XEN) EDID info not retrieved because of reasons unknown (XEN) Disc information: (XEN) Found 4 MBR signatures (XEN) Found 4 EDD information structures (XEN) Xen-e820 RAM map: (XEN) 0000000000000000 - 000000000009f000 (usable) (XEN) 000000000009f000 - 00000000000a0000 (reserved) (XEN) 00000000000f0000 - 0000000000100000 (reserved) (XEN) 0000000000100000 - 00000000ddee0000 (usable) (XEN) 00000000ddee0000 - 00000000ddee3000 (ACPI NVS) (XEN) 00000000ddee3000 - 00000000ddef0000 (ACPI data) (XEN) 00000000ddef0000 - 00000000ddf00000 (reserved) (XEN) 00000000e0000000 - 00000000f0000000 (reserved) (XEN) 00000000fec00000 - 0000000100000000 (reserved) (XEN) 0000000100000000 - 0000000220000000 (usable) (XEN) System RAM: 8158MB (8354300kB) (XEN) ACPI: RSDP 000F8210, 0024 (r2 ATI ) (XEN) ACPI: XSDT DDEE3100, 0044 (r1 ATI ASUSACPI 42302E31 AWRD 0) (XEN) ACPI: FACP DDEE8500, 00F4 (r3 ATI ASUSACPI 42302E31 AWRD 0) (XEN) ACPI: DSDT DDEE3280, 5210 (r1 ATI ASUSACPI 1000 MSFT 3000000) (XEN) ACPI: FACS DDEE0000, 0040 (XEN) ACPI: HPET DDEE8740, 0038 (r1 ATI ASUSACPI 42302E31 AWRD 98) (XEN) ACPI: MCFG DDEE87C0, 003C (r1 ATI ASUSACPI 42302E31 AWRD 0) (XEN) ACPI: APIC DDEE8640, 0084 (r1 ATI ASUSACPI 42302E31 AWRD 0) (XEN) NUMA turned off (XEN) Faking a node at 0000000000000000-0000000220000000 (XEN) Domain heap initialised (XEN) found SMP MP-table at 000f6560 (XEN) DMI 2.4 present. (XEN) Using APIC driver default (XEN) ACPI: PM-Timer IO Port: 0x4008 (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[4004,0], pm1x_evt[4000,0] (XEN) ACPI: wakeup_vec[ddee000c], vec_size[20] (XEN) ACPI: Local APIC address 0xfee00000 (XEN) ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) (XEN) Processor #0 15:11 APIC version 16 (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) (XEN) Processor #1 15:11 APIC version 16 (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) (XEN) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) (XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) (XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) (XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) (XEN) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) (XEN) IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23 (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) (XEN) ACPI: IRQ0 used by override. (XEN) ACPI: IRQ2 used by override. (XEN) ACPI: IRQ9 used by override. (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs (XEN) ACPI: HPET id: 0x8200 base: 0xfed00000 (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 (XEN) PCI: MCFG area at e0000000 reserved in E820 (XEN) Using ACPI (MADT) for SMP configuration information (XEN) Using scheduler: SMP Credit Scheduler (credit) (XEN) Initializing CPU#0 (XEN) Detected 2400.019 MHz processor. (XEN) CPU0: AMD Flush Filter disabled (XEN) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) (XEN) CPU: L2 Cache: 512K (64 bytes/line) (XEN) CPU 0(2) -> Core 0 (XEN) AMD SVM: ASIDs disabled. (XEN) HVM: SVM enabled (XEN) CPU0: AMD K8 machine check reporting enabled (XEN) I/O virtualisation disabled (XEN) CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 02 (XEN) Booting processor 1/1 eip 8c000 (XEN) Initializing CPU#1 (XEN) CPU1: AMD Flush Filter disabled (XEN) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) (XEN) CPU: L2 Cache: 512K (64 bytes/line) (XEN) CPU 1(2) -> Core 1 (XEN) AMD: Disabling C1 Clock Ramping Node #0 (XEN) AMD SVM: ASIDs disabled. (XEN) CPU1: AMD K8 machine check reporting enabled (XEN) CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 02 (XEN) Total of 2 processors activated. (XEN) ENABLING IO-APIC IRQs (XEN) -> Using new ACK method (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 (XEN) checking TSC synchronization across 2 CPUs: (XEN) CPU#0 had -662 usecs TSC skew, fixed it up. (XEN) CPU#1 had 662 usecs TSC skew, fixed it up. (XEN) Platform timer is 14.318MHz HPET (XEN) Brought up 2 CPUs (XEN) do_IRQ: 1.231 No irq handler for vector (irq -1) (XEN) microcode.c:73:d32767 microcode: CPU1 resumed (XEN) HPET: 4 timers in total, 0 timers will be used for broadcast (XEN) ACPI sleep modes: S3 (XEN) MCA: Use hw thresholding to adjust polling frequency (XEN) mcheck_poll: Machine check polling timer started. (XEN) *** LOADING DOMAIN 0 *** (XEN) elf_parse_binary: phdr: paddr=0xffffffff80200000 memsz=0x26a870 (XEN) elf_parse_binary: phdr: paddr=0xffffffff8046b000 memsz=0x868e8 (XEN) elf_parse_binary: phdr: paddr=0xffffffff804f2000 memsz=0xc08 (XEN) elf_parse_binary: phdr: paddr=0xffffffff804f4000 memsz=0xccc1c (XEN) elf_parse_binary: memory: 0xffffffff80200000 -> 0xffffffff805c0c1c (XEN) elf_xen_parse_note: GUEST_OS = "linux" (XEN) elf_xen_parse_note: GUEST_VERSION = "2.6" (XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0" (XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 (XEN) elf_xen_parse_note: PADDR_OFFSET = 0xffffffff80000000 (XEN) elf_xen_parse_note: ENTRY = 0xffffffff80200000 (XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80206000 (XEN) elf_xen_parse_note: unknown xen elf note (0xd) (XEN) elf_xen_parse_note: FEATURES = "writable_page_tables|writable_descriptor_tables|auto_translated_physmap|pae_pgdir_above_4gb|supervisor_mode_kernel" (XEN) elf_xen_parse_note: LOADER = "generic" (XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1 (XEN) elf_xen_addr_calc_check: addresses: (XEN) virt_base = 0xffffffff80000000 (XEN) elf_paddr_offset = 0xffffffff80000000 (XEN) virt_offset = 0x0 (XEN) virt_kstart = 0xffffffff80200000 (XEN) virt_kend = 0xffffffff805c0c1c (XEN) virt_entry = 0xffffffff80200000 (XEN) p2m_base = 0xffffffffffffffff (XEN) Xen kernel: 64-bit, lsb, compat32 (XEN) Dom0 kernel: 64-bit, lsb, paddr 0xffffffff80200000 -> 0xffffffff805c0c1c (XEN) PHYSICAL MEMORY ARRANGEMENT: (XEN) Dom0 alloc.: 0000000214000000->0000000218000000 (2014025 pages to be allocated) (XEN) VIRTUAL MEMORY ARRANGEMENT: (XEN) Loaded kernel: ffffffff80200000->ffffffff805c0c1c (XEN) Init. ramdisk: ffffffff805c1000->ffffffff817ec800 (XEN) Phys-Mach map: ffffffff817ed000->ffffffff8276aa48 (XEN) Start info: ffffffff8276b000->ffffffff8276b4b4 (XEN) Page tables: ffffffff8276c000->ffffffff82785000 (XEN) Boot stack: ffffffff82785000->ffffffff82786000 (XEN) TOTAL: ffffffff80000000->ffffffff82c00000 (XEN) ENTRY ADDRESS: ffffffff80200000 (XEN) Dom0 has maximum 2 VCPUs (XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 -> 0xffffffff8046a870 (XEN) elf_load_binary: phdr 1 at 0xffffffff8046b000 -> 0xffffffff804f18e8 (XEN) elf_load_binary: phdr 2 at 0xffffffff804f2000 -> 0xffffffff804f2c08 (XEN) elf_load_binary: phdr 3 at 0xffffffff804f4000 -> 0xffffffff8052dff8 (XEN) Scrubbing Free RAM: .done. (XEN) Xen trace buffers: disabled (XEN) Std. Loglevel: All (XEN) Guest Loglevel: All (XEN) Xen is relinquishing VGA console. (XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to switch input to Xen) (XEN) Freed 140kB init memory. (XEN) io_apic.c:2206: (XEN) ioapic_guest_write: apic=0, pin=2, irq=0 (XEN) ioapic_guest_write: new_entry=00000900 (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! (XEN) PCI add device 00:14.1 (XEN) Set CPU acpi_id(0) cpuid(0) Px State info: (XEN) _PPC: 0 (XEN) Set CPU acpi_id(1) cpuid(1) Px State info: (XEN) _PPC: 0 (XEN) no cpu_id for acpi_id 2 (XEN) no cpu_id for acpi_id 3 (XEN) PCI add device 00:13.0 (XEN) allocated vector for irq:16 (XEN) PCI add device 00:13.1 (XEN) allocated vector for irq:17 (XEN) PCI add device 00:13.2 (XEN) allocated vector for irq:18 (XEN) PCI add device 00:13.3 (XEN) PCI add device 00:13.4 (XEN) PCI add device 00:13.5 (XEN) allocated vector for irq:19 (XEN) PCI add device 00:14.1 (XEN) PCI add device 02:00.0 (XEN) PCI add device 00:12.0 (XEN) allocated vector for irq:22

_______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-devel

©2013 Xen Project, A Linux Foundation Collaborative Project. All Rights Reserved.
Linux Foundation is a registered trademark of The Linux Foundation.
Xen Project is a trademark of The Linux Foundation.