Re: [Xen-API] bnx2 driver failed in linux-2.6.18.8-xen-3.4.2, Dell R610

[Pasi Kärkkäinen <pasik@xxxxxx>]

On Sat, Nov 13, 2010 at 04:43:25AM +0800, Luwei Cheng wrote:
>    Hello Bruce,
>    Thanks for your reply. In my kernel, I did not
>    find CONFIG_FIRMWARE_IN_KERNEL.
>    There are only 4 options related to firmware in my kernel:
>    CONFIG_PREVENT_FIRMWARE_BUILD=y
>    CONFIG_HOSTAP_FIRMWARE=y
>    CONFIG_HOSTAP_FIRMWARE_NVRAM=y
>    CONFIG_FIRMWARE_EDID=y
>    Any idea?

http://wiki.xen.org/xenwiki/XenParavirtOps

especially read the troubleshooting section.
It has instructions how to build the kernel,
and also it has reference .config files with working kernel configuration.

-- Pasi


>    Best,
>    -Luwei
>    On Sat, Nov 13, 2010 at 4:26 AM, Bruce Edge <[1]bruce.edge@xxxxxxxxx>
>    wrote:
> 
>      On Fri, Nov 12, 2010 at 12:10 PM, Luwei Cheng <[2]chengluwei@xxxxxxxxx>
>      wrote:
>      > So many issues I did not expect to have... I think I need a 2.6.18
>      stable
>      > kernel to run.
>      > Actually I have only ONE step to succeed in 2.6.18.8. Any one who
>      knows how
>      > to patch bnx2 dirver?
>      > Deep thanks!
>      > --Luwei
>      >
>      > On Sat, Nov 13, 2010 at 2:05 AM, Luwei Cheng <[3]chengluwei@xxxxxxxxx>
>      wrote:
>      >>
>      >> Yes, I am already in progress to install 2.6.32 with long time to git
>      >> clone... hope not too much trouble shooting:-)
>      >> Anyway, if there's any patch to 2.6.18.8-bnx2 driver, I'd like it
>      more.
>      >> Regards,
>      >> Luwei
> 
>      Not sure if this is related to your specific problem, but to use a
>      BNX2 NIC I need to enable
>         CONFIG_FIRMWARE_IN_KERNEL=y
>      in order to pull the BNX2 firmware into the kernel, otherwise it
>      complains that it can't find the firmware at boot time.
> 
>      -Bruce
>      >>
>      >> On Sat, Nov 13, 2010 at 1:56 AM, Konrad Rzeszutek Wilk
>      >> <[4]konrad.wilk@xxxxxxxxxx> wrote:
>      >>>
>      >>> On Sat, Nov 13, 2010 at 01:19:03AM +0800, Luwei Cheng wrote:
>      >>> > Hello Konrad,
>      >>> >
>      >>> > Thanks for your reply to enlighten me.
>      >>> >
>      >>> > This is almost the first time that I compile XenLinux from source.
>      To
>      >>> > play
>      >>> > safe, I just downloaded the source code from [5]www.xen.org.
>      >>> > Is 2.6.32-PVOPS already stable kernel? Is there any document to
>      follow
>      >>> > so
>      >>> > that I won't miss some steps? Thanks!
>      >>>
>      >>> Look on Google for "Wiki PVOPS" and it will direct you the Wiki on
>      how to
>      >>> do it.
>      >>
>      >
>      >
>      > _______________________________________________
>      > xen-api mailing list
>      > [6]xen-api@xxxxxxxxxxxxxxxxxxx
>      > [7]http://lists.xensource.com/mailman/listinfo/xen-api
>      >
>      >
> 
> References
> 
>    Visible links
>    1. mailto:bruce.edge@xxxxxxxxx
>    2. mailto:chengluwei@xxxxxxxxx
>    3. mailto:chengluwei@xxxxxxxxx
>    4. mailto:konrad.wilk@xxxxxxxxxx
>    5. http://www.xen.org/
>    6. mailto:xen-api@xxxxxxxxxxxxxxxxxxx
>    7. http://lists.xensource.com/mailman/listinfo/xen-api

> _______________________________________________
> xen-api mailing list
> xen-api@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/mailman/listinfo/xen-api


_______________________________________________
xen-api mailing list
xen-api@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/mailman/listinfo/xen-api