Re: [UNIKRAFT/LIBLWIP PATCH v3 00/16] Introduce a tap driver for Unikraft

[Sharan Santhanam <sharan.santhanam@xxxxxxxxx>]

Please ignore this patch series. The patch series is intended for the 
Unikraft and not lwip.
Thanks & Regards
Sharan

On 7/22/20 12:03 PM, Sharan Santhanam wrote:
> The patch series introduces a tap driver for the linuxu platform. The series is
> structured as follows:
> - Introduce the uk_netdev interface implemented by the tap driver
> - Introduce pseudo tap bus to initialize the driver and probe a tap device.
> - The tap device discovered are registered with the uk_netdev.
> - Configure the netdevice by creating tap network interface.
> - Configure the hw address on the tap device.
> - Attach the tap device to a bridge interface.
> - Fetch and configure the MTU.
> - Check if the promiscuous mode is set
> - Fetch the txq/rxq information.
> - Configure the tx queue.
> - Configure the rx queue.
> - Start the tap interface.
> - Implement packet receive on the tap interface
> - Implement packet send on the tap interface
> - Fix the error code difference between Unikraft and linux.
>
> Changes since v2:
> - Fix the tap_write implementation
> - Change the mac generate implementation
> - Minor fixes
> - Make feature independent from the poll patch
>
> Changes since v1:
> - Complete the sys_open implementation with support for flags
> - Fix bug in calloc usage.
> - Move definitions into the required patches
> - Add some comments for the library parameters
> - Add descriptions to the struct definitions
> - Fix some typos.
>
>
> Sharan Santhanam (16):
>    plat/linuxu/tap: Introduce tap driver
>    plat/tap: Bus interface for the tap device
>    plat/driver: Add tap device to the uk_netdev
>    plat/driver: Create a tap dev during configuration
>    plat/driver: Set features supported on tap device
>    plat/tap: Get/Set hw_addr
>    plat/tap: Add tap to the bridge
>    plat/tap: Get/Set MTU
>    plat/tap: Get promiscuous mode
>    plat/tap: Fetch txq and rxq info
>    plat/tap: Setup txq
>    plat/tap: Setup rxq
>    plat/tap: Start a tap device
>    plat/tap: Support tap_netdev_recv
>    plat/tap: Support tap_netdev_xmit
>    plat/linuxu: Convert linux errno to unikraft errno
>
>   plat/drivers/include/tap/tap.h              |  51 ++
>   plat/drivers/tap/tap.c                      | 868 ++++++++++++++++++++
>   plat/linuxu/Config.uk                       |  18 +
>   plat/linuxu/Makefile.uk                     |  15 +
>   plat/linuxu/include/linuxu/syscall-arm_32.h |   6 +
>   plat/linuxu/include/linuxu/syscall-x86_64.h |   7 +
>   plat/linuxu/include/linuxu/syscall.h        |  86 ++
>   plat/linuxu/include/linuxu/tap.h            | 152 ++++
>   plat/linuxu/tap_io.c                        | 160 ++++
>   9 files changed, 1363 insertions(+)
>   create mode 100644 plat/drivers/include/tap/tap.h
>   create mode 100644 plat/drivers/tap/tap.c
>   create mode 100644 plat/linuxu/include/linuxu/tap.h
>   create mode 100644 plat/linuxu/tap_io.c