|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [Minios-devel] [UNIKRAFT RFC PATCH 1/2] Implement gic-v2 library for Arm
This library has implemented basic GICv2 functions. We don't support
GICv2M and security extension in this library.
Signed-off-by: Wei Chen <wei.chen@xxxxxxx>
Signed-off-by: Jianyong Wu <jianyong.wu@xxxxxxx>
---
plat/common/arm/gic-v2.c | 394 +++++++++++++++++++++++++++++++++++++++
plat/common/include/arm/gic-v2.h | 380 +++++++++++++++++++++++++++++++++++++
plat/common/include/irq.h | 15 ++
plat/kvm/Makefile.uk | 1 +
plat/kvm/arm/setup.c | 61 +++---
5 files changed, 824 insertions(+), 27 deletions(-)
create mode 100644 plat/common/arm/gic-v2.c
create mode 100644 plat/common/include/arm/gic-v2.h
diff --git a/plat/common/arm/gic-v2.c b/plat/common/arm/gic-v2.c
new file mode 100644
index 0000000..d212cfa
--- /dev/null
+++ b/plat/common/arm/gic-v2.c
@@ -0,0 +1,394 @@
+/* SPDX-License-Identifier: BSD-3-Clause */
+/*
+ * Authors: Wei Chen <Wei.Chen@xxxxxxx>
+ * Jianyong Wu <Jianyong.Wu@xxxxxxx>
+ *
+ * Copyright (c) 2018, Arm Ltd. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the name of the copyright holder nor the names of its
+ * contributors may be used to endorse or promote products derived from
+ * this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ * THIS HEADER MAY NOT BE EXTRACTED OR MODIFIED IN ANY WAY.
+ */
+#include <string.h>
+#include <libfdt.h>
+#include <uk/essentials.h>
+#include <uk/print.h>
+#include <uk/assert.h>
+#include <uk/bitops.h>
+#include <uk/asm.h>
+#include <irq.h>
+#include <arm/cpu.h>
+#include <arm/gic-v2.h>
+
+static void *gic_dist_addr, *gic_cpuif_addr;
+static uint64_t gic_dist_size, gic_cpuif_size;
+
+#define GIC_DIST_REG(r) (gic_dist_addr + (r))
+#define GIC_CPU_REG(r) (gic_cpuif_addr + (r))
+
+static char *gic_device_list[] = {
+ "arm,cortex-a15-gic",
+ "arm,cortex-a7-gic",
+ "arm,cortex-a9-gic",
+ "arm,gic-400",
+ "arm,eb11mp-gic",
+ "arm,pl390",
+ "arm,arm1176jzf-devchip-gic",
+ "arm,arm11mp-gic",
+ "arm,tc11mp-gic",
+ "brcm,brahma-b15-gic",
+ "nvidia,tegra210-agic",
+ "qcom,msm-8660-qgic",
+ "qcom,msm-qgic2",
+};
+
+/* inline functions to access GICC & GICD registers */
+static inline void write_gicd8(uint64_t offset, uint8_t val)
+{
+ ioreg_write8(GIC_DIST_REG(offset), val);
+}
+
+static inline void write_gicd32(uint64_t offset, uint32_t val)
+{
+ ioreg_write32(GIC_DIST_REG(offset), val);
+}
+
+static inline uint32_t read_gicd32(uint64_t offset)
+{
+ return ioreg_read32(GIC_DIST_REG(offset));
+}
+
+static inline void write_gicc32(uint64_t offset, uint32_t val)
+{
+ ioreg_write32(GIC_CPU_REG(offset), val);
+}
+
+static inline uint32_t read_gicc32(uint64_t offset)
+{
+ return ioreg_read32(GIC_CPU_REG(offset));
+}
+
+/*
+ * Functions of GIC CPU interface
+ */
+
+/* Enable GIC cpu interface */
+static void gic_enable_cpuif(void)
+{
+ /* just set bit 0 to 1 to enable cpu interface */
+ write_gicc32(GICC_CTLR, GICC_CTLR_ENABLE);
+}
+
+/* Set priority threshold for processor */
+static void gic_set_threshold_priority(uint32_t threshold_prio)
+{
+ /* GICC_PMR allocate 1 byte for each irq */
+ UK_ASSERT(threshold_prio <= GICC_PMR_PRIO_MAX);
+ write_gicc32(GICC_PMR, threshold_prio);
+}
+
+/*
+ * Acknowledging irq equals reading GICC_IAR also
+ * get the interrupt ID as the side effect.
+ */
+uint32_t gic_ack_irq(void)
+{
+ return read_gicc32(GICC_IAR);
+}
+
+/*
+ * write to GICC_EOIR to inform cpu interface completation
+ * of interrupt processing. If GICC_CTLR.EOImode sets to 1
+ * this func just gets priority drop.
+ */
+void gic_eoi_irq(uint32_t irq)
+{
+ write_gicc32(GICC_EOIR, irq);
+}
+
+/* Functions of GIC Distributor */
+
+/*
+ * @sgintid denotes the sgi ID;
+ * @targetfilter : this term is TargetListFilter
+ * 0 denotes forwarding interrupt to cpu specified in the
+ * target list; 1 denotes forwarding interrupt to cpu execpt the
+ * processor that request the intrrupt; 2 denotes forwarding the
+ * interrupt only to the cpu that requtest the interrupt.
+ * @targetlist is bitmask, which bit 1 denotes forwarding to and only low 8
+ * bit is in use.
+ */
+static void gic_sgi_gen(uint32_t sgintid, uint8_t targetfilter,
+ uint8_t targetlist)
+{
+ uint32_t val;
+
+ /* Only INTID 0-15 allocated to sgi */
+ UK_ASSERT(sgintid <= GICD_SGI_MAX_INITID);
+
+ /* Set SGI tagetfileter field */
+ val = (targetfilter & GICD_SGI_FILTER_MASK) << GICD_SGI_FILTER_SHIFT;
+
+ /* Set SGI targetlist field */
+ val |= (targetlist & GICD_SGI_TARGET_MASK) << GICD_SGI_TARGET_SHIFT;
+
+ /* Set SGI INITID field */
+ val |= sgintid;
+
+ /* Generate SGI */
+ write_gicd32(GICD_SGIR, val);
+}
+
+/*
+ * Forward the SIG to the CPU interfaces specified in the
+ * targetlist. Targetlist is a 8-bit bitmap for 0~7 CPU.
+ * TODO: this will not work untill SMP is supported
+ */
+void gic_sgi_gen_to_list(uint32_t sgintid, uint8_t targetlist)
+{
+ gic_sgi_gen(sgintid, GICD_SGI_FILTER_TO_LIST, targetlist);
+}
+
+/*
+ * Forward the SGI to all CPU interfaces except that of the
+ * processor that requested the interrupt.
+ * TODO: this will not work untill SMP is supported
+ */
+void gic_sgi_gen_to_others(uint32_t sgintid)
+{
+ gic_sgi_gen(sgintid, GICD_SGI_FILTER_TO_OTHERS, 0);
+}
+
+/*
+ * Forward the SGI only to the CPU interface of the processor
+ * that requested the interrupt.
+ */
+void gic_sgi_gen_to_self(uint32_t sgintid)
+{
+ gic_sgi_gen(sgintid, GICD_SGI_FILTER_TO_SELF, 0);
+}
+
+/*
+ * set target cpu for irq in distributor,
+ * @target: bitmask value, bit 1 indicates target to
+ * corresponding cpu interface
+ */
+void gic_set_irq_target(uint32_t irq, uint8_t target)
+{
+ write_gicd8(GICD_ITARGETSR(irq), target);
+}
+
+/* set priority for irq in distributor */
+void gic_set_irq_prio(uint32_t irq, uint8_t priority)
+{
+ write_gicd8(GICD_IPRIORITYR(irq), priority);
+}
+
+/*
+ * Enable an irq in distributor, each irq occupies one bit
+ * to configure in corresponding registor
+ */
+void gic_enable_irq(uint32_t irq)
+{
+ write_gicd32(GICD_ISENABLER(irq),
+ UK_BIT(irq % GICD_I_PER_ISENABLERn));
+}
+
+/*
+ * Disable an irq in distributor, one bit reserved for an irq
+ * to configure in corresponding register
+ */
+void gic_disable_irq(uint32_t irq)
+{
+ write_gicd32(GICD_ICENABLER(irq),
+ UK_BIT(irq % GICD_I_PER_ICENABLERn));
+}
+
+/* Enable distributor */
+static void gic_enable_dist(void)
+{
+ /* just set bit 0 to 1 to enable distributor */
+ write_gicd32(GICD_CTLR, read_gicd32(GICD_CTLR) | GICD_CTLR_ENABLE);
+}
+
+/* disable distributor */
+static void gic_disable_dist(void)
+{
+ /* just clear bit 0 to 0 to enable distributor */
+ write_gicd32(GICD_CTLR, read_gicd32(GICD_CTLR) & (~GICD_CTLR_ENABLE));
+}
+
+/* Config intrrupt trigger type and polarity */
+void gic_set_irq_type(uint32_t irq, int trigger, int polarity)
+{
+ uint32_t val, mask, oldmask;
+
+ if ((trigger >= UK_IRQ_TRIGGER_MAX) ||
+ (polarity >= UK_IRQ_POLARITY_MAX))
+ return;
+
+ val = read_gicd32(GICD_ICFGR(irq));
+ mask = oldmask = (val >> ((irq % GICD_I_PER_ICFGRn) * 2)) &
+ GICD_ICFGR_MASK;
+
+ if (trigger == UK_IRQ_TRIGGER_LEVEL) {
+ mask &= ~GICD_ICFGR_TRIG_MASK;
+ mask |= GICD_ICFGR_TRIG_LVL;
+ } else if (trigger == UK_IRQ_TRIGGER_EDGE) {
+ mask &= ~GICD_ICFGR_TRIG_MASK;
+ mask |= GICD_ICFGR_TRIG_EDGE;
+ }
+
+ if (polarity == UK_IRQ_POLARITY_LOW) {
+ mask &= ~GICD_ICFGR_POL_MASK;
+ mask |= GICD_ICFGR_POL_LOW;
+ } else if (polarity == UK_IRQ_POLARITY_HIGH) {
+ mask &= ~GICD_ICFGR_POL_MASK;
+ mask |= GICD_ICFGR_POL_HIGH;
+ }
+
+ /* Check if nothing changed */
+ if (mask == oldmask)
+ return;
+
+ /* Update new interrupt type */
+ val &= (~(GICD_ICFGR_MASK << (irq % GICD_I_PER_ICFGRn) * 2));
+ val |= (mask << (irq % GICD_I_PER_ICFGRn) * 2);
+ write_gicd32(GICD_ICFGR(irq), val);
+}
+
+static void gic_init_dist(void)
+{
+ uint32_t val, cpuif_number, irq_number;
+ uint32_t i;
+
+ /* Turn down distributor */
+ gic_disable_dist();
+
+ /* Get GIC CPU interface */
+ val = read_gicd32(GICD_TYPER);
+ cpuif_number = GICD_TYPER_CPUI_NUM(val);
+ if (cpuif_number > GIC_MAX_CPUIF)
+ cpuif_number = GIC_MAX_CPUIF;
+ uk_printd(DLVL_INFO, "GICv2 Max CPU interface:%d\n", cpuif_number);
+
+ /* Get the maximum number of interrupts that the GIC supports */
+ irq_number = GICD_TYPER_LINE_NUM(val);
+ if (irq_number > GIC_MAX_IRQ)
+ irq_number = GIC_MAX_IRQ;
+ uk_printd(DLVL_INFO, "GICv2 Max interrupt lines:%d\n", irq_number);
+ /*
+ * Set all SPI interrupts targets to all CPU.
+ */
+ for (i = GIC_SPI_BASE; i < irq_number; i += GICD_I_PER_ITARGETSRn)
+ write_gicd32(GICD_ITARGETSR(i), GICD_ITARGETSR_DEF);
+
+ /*
+ * Set all SPI interrupts type to be polarity low level triggered
+ */
+ for (i = GIC_SPI_BASE; i < irq_number; i += GICD_I_PER_ICFGRn)
+ write_gicd32(GICD_ICFGR(i), GICD_ICFGR_DEF_TYPE);
+
+ /*
+ * Set all SPI priority to a default value.
+ */
+ for (i = GIC_SPI_BASE; i < irq_number; i += GICD_I_PER_IPRIORITYn)
+ write_gicd32(GICD_IPRIORITYR(i), GICD_IPRIORITY_DEF);
+
+ /*
+ * Deactivate and disable all SPIs.
+ */
+ for (i = GIC_SPI_BASE; i < irq_number; i += GICD_I_PER_ICACTIVERn) {
+ write_gicd32(GICD_ICACTIVER(i), GICD_DEF_ICACTIVERn);
+ write_gicd32(GICD_ICENABLER(i), GICD_DEF_ICENABLERn);
+ }
+
+ /* turn on distributor */
+ gic_enable_dist();
+}
+
+static void gic_init_cpuif(void)
+{
+ uint32_t i;
+ /* set priority mask to the lowest priority to let all irq visible to
cpu interface */
+ gic_set_threshold_priority(GICC_PMR_PRIO_MAX);
+
+ /* set PPI and SGI to polarity low level triggered */
+ for (i = 0; i < GIC_SPI_BASE; i += GICD_I_PER_ICFGRn)
+ write_gicd32(GICD_ICFGR(i), GICD_ICFGR_DEF_TYPE);
+
+ /* set PPI and SGI to a default value */
+ for (i = 0; i < GIC_SPI_BASE; i += GICD_I_PER_IPRIORITYn)
+ write_gicd32(GICD_IPRIORITYR(i), GICD_IPRIORITY_DEF);
+ /*
+ * Deactivate and disable all PPIs.
+ */
+ for (i = 0; i < GICD_SGI_MAX_INITID; i += GICD_I_PER_ICACTIVERn) {
+ write_gicd32(GICD_ICACTIVER(i), GICD_DEF_ICACTIVERn);
+ write_gicd32(GICD_ICENABLER(i), GICD_DEF_PPI_ICENABLERn);
+ }
+ /* Deactivate and enable all SGIs */
+ for (i = 0; i < GIC_PPI_BASE; i += GICD_I_PER_ICACTIVERn)
+ {
+ write_gicd32(GICD_ICACTIVER(i), GICD_DEF_ICACTIVERn);
+ write_gicd32(GICD_ISENABLER(i), GICD_DEF_SGI_ISENABLERn);
+ }
+
+ /* enable cpu interface */
+ gic_enable_cpuif();
+}
+
+int _dtb_init_gic(void *dtb)
+{
+ uint32_t idx;
+ int fdt_gic;
+ uint32_t naddr, nsize;
+ const uint64_t *regs;
+
+ uk_printd(DLVL_INFO, "Probing GICv2...\n");
+ /* Currently, we only support 1 GIC per system */
+ fdt_gic = uk_dtb_find_device(dtb, gic_device_list,
sizeof(gic_device_list));
+
+ /* Get region size at regs region in dtb */
+ naddr = uk_dtb_read_region(dtb, fdt_gic, &nsize, ®s);
+
+ /* Get device address and size at regs region */
+ gic_dist_addr = (void *)uk_dtb_read_term(regs, 0, naddr, nsize,
&gic_dist_size);
+ gic_cpuif_addr = (void *)uk_dtb_read_term(regs, 1, naddr, nsize,
&gic_cpuif_size);
+
+ uk_printd(DLVL_INFO, "Found GICv2 on:\n");
+ uk_printd(DLVL_INFO, "\tCPU interface address: %p\n", gic_cpuif_addr);
+ uk_printd(DLVL_INFO, "\tDistributor address: %p\n", gic_dist_addr);
+
+
+ /* Initialize GICv2 distributor */
+ gic_init_dist();
+
+ /* Initialize GICv2 CPU interface */
+ gic_init_cpuif();
+
+ return 0;
+}
diff --git a/plat/common/include/arm/gic-v2.h b/plat/common/include/arm/gic-v2.h
new file mode 100644
index 0000000..dfee6a8
--- /dev/null
+++ b/plat/common/include/arm/gic-v2.h
@@ -0,0 +1,380 @@
+/* SPDX-License-Identifier: BSD-3-Clause */
+/*
+ * Authors: Wei Chen <Wei.Chen@xxxxxxx>
+ * Jianyong Wu <Jianyong.Wu@xxxxxxx>
+ *
+ * Copyright (c) 2018, Arm Ltd. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the name of the copyright holder nor the names of its
+ * contributors may be used to endorse or promote products derived from
+ * this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ * THIS HEADER MAY NOT BE EXTRACTED OR MODIFIED IN ANY WAY.
+ */
+#ifndef __PLAT_CMN_ARM_GIC_H__
+#define __PLAT_CMN_ARM_GIC_H__
+
+/*
+ * Distributor registers. Unikraft only support run on non-secure
+ * so we just describe non-secure registers.
+ */
+
+/*
+ * Distributor Control Register, GICD_CTLR.
+ * Enables the forwarding of pending interrupts from the
+ * Distributor to the CPU interfaces
+ */
+#define GICD_CTLR 0x0000
+#define GICD_CTLR_ENABLE 0x1
+
+/*
+ * Interrupt Controller Type Register, GICD_TYPER.
+ * Provides information about the configuration of the GIC.
+ */
+#define GICD_TYPER 0x0004
+#define GICD_TYPER_LINE_NUM(r) ((((r) & 0x1f) + 1) << 5)
+#define GICD_TYPER_CPUI_NUM(r) ((((r) >> 5) & 0x3) + 1)
+
+/*
+ * Distributor Implementer Identification Register, GICD_IIDR.
+ * Provides information about the implementer and revision of the Distributor.
+ */
+#define GICD_IIDR 0x0008
+#define GICD_IIDR_PROD(r) (((r) >> 24) & 0xff)
+#define GICD_IIDR_VAR(r) (((r) >> 16) & 0xf)
+#define GICD_IIDR_REV(r) (((r) >> 12) & 0xf)
+#define GICD_IIDR_IMPL(r) ((r) & 0xfff)
+
+/*
+ * Interrupt Group Registers, GICD_IGROUPRn
+ * These registers provide a status bit for each interrupt supported by
+ * the GIC. Each bit controls whether the corresponding interrupt is in
+ * Group 0 or Group 1
+ */
+#define GICD_IGROUPR(n) (0x0080 + 4 * ((n) >> 5))
+#define GICD_I_PER_IGROUPRn 32
+
+/*
+ * Interrupt Set-Enable Registers, GICD_ISENABLERn.
+ * These registers provide a Set-enable bit for each interrupt supported
+ * by the GIC. Writing 1 to a Set-enable bit enables forwarding of the
+ * corresponding interrupt from the Distributor to the CPU interfaces.
+ * Reading a bit identifies whether the interrupt is enabled.
+ */
+#define GICD_ISENABLER(n) (0x0100 + 4 * ((n) >> 5))
+#define GICD_I_PER_ISENABLERn 32
+#define GICD_DEF_SGI_ISENABLERn 0xffff
+
+/*
+ * Interrupt Clear-Enable Registers, GICD_ICENABLERn.
+ * Provide a Clear-enable bit for each interrupt supported by the GIC.
+ * Writing 1 to a Clear-enable bit disables forwarding of the
+ * corresponding interrupt from the Distributor to the CPU interfaces.
+ * Reading a bit identifies whether the interrupt is enabled.
+ */
+#define GICD_ICENABLER(n) (0x0180 + 4 * ((n) >> 5))
+#define GICD_I_PER_ICENABLERn 32
+#define GICD_DEF_ICENABLERn 0xffffffff
+#define GICD_DEF_PPI_ICENABLERn 0xffff0000
+
+/*
+ * Interrupt Set-Pending Registers, GICD_ISPENDRn.
+ * Provide a Set-pending bit for each interrupt supported by the GIC.
+ * Writing 1 to a Set-pending bit sets the status of the corresponding
+ * peripheral interrupt to pending. Reading a bit identifies whether
+ * the interrupt is pending.
+ */
+#define GICD_ISPENDR(n) (0x0200 + 4 * ((n) >> 5))
+#define GICD_I_PER_ISPENDRn 32
+/*
+ * Interrupt Clear-Pending Registers, GICD_ICPENDRn
+ * Provide a Clear-pending bit for each interrupt supported by the GIC.
+ * Writing 1 to a Clear-pending bit clears the pending state of the
+ * corresponding peripheral interrupt. Reading a bit identifies whether
+ * the interrupt is pending.
+ */
+#define GICD_ICPENDR(n) (0x0280 + 4 * ((n) >> 5))
+#define GICD_I_PER_ICPENDRn 32
+
+/*
+ * Interrupt Set-Active Registers, GICD_ISACTIVERn
+ * Provide a Set-active bit for each interrupt that the GIC supports.
+ * Writing to a Set-active bit Activates the corresponding interrupt.
+ * These registers are used when preserving and restoring GIC state.
+ */
+#define GICD_ISACTIVER(n) (0x0300 + 4 * ((n) >> 5))
+#define GICD_I_PER_ISACTIVERn 32
+/*
+ * Interrupt Clear-Active Registers, GICD_ICACTIVERn
+ * Provide a Clear-active bit for each interrupt that the GIC supports.
+ * Writing to a Clear-active bit Deactivates the corresponding interrupt.
+ * These registers are used when preserving and restoring GIC state.
+ */
+#define GICD_ICACTIVER(n) (0x0380 + 4 * ((n) >> 5))
+#define GICD_I_PER_ICACTIVERn 32
+#define GICD_DEF_ICACTIVERn 0xffffffff
+
+/*
+ * Interrupt ID mask for GICD_ISENABLER, GICD_ICENABLER, GICD_ISPENDR,
+ * GICD_ICPENDR, GICD_ISACTIVER and GICD_ICACTIVER
+ */
+#define GICD_I_MASK(n) (1ul << ((n) & 0x1f))
+
+/*
+ * Interrupt Priority Registers, GICD_IPRIORITYRn
+ * Provide an 8-bit priority field for each interrupt supported by the
+ * GIC.
+ *
+ * These registers are byte-accessible, so we define this macro
+ * for byte-access.
+ */
+#define GICD_IPRIORITYR(n) (0x0400 + (n))
+#define GICD_I_PER_IPRIORITYn 4
+#define GICD_IPRIORITY_DEF 0xa0a0a0a0
+
+/*
+ * Interrupt Processor Targets Registers, GICD_ITARGETSRn
+ * Provide an 8-bit CPU targets field for each interrupt supported by
+ * the GIC.
+ *
+ * These registers are byte-accessible, so we define this macro
+ * for byte-access.
+ */
+#define GICD_ITARGETSR(n) (0x0800 + (n))
+#define GICD_I_PER_ITARGETSRn 4
+#define GICD_ITARGETSR_DEF 0xffffffff
+
+/*
+ * Interrupt Configuration Registers, GICD_ICFGRn
+ * The GICD_ICFGRs provide a 2-bit Int_config field for each interrupt
+ * supported by the GIC. This field identifies whether the corresponding
+ * interrupt is edge-triggered or level-sensitive.
+ */
+#define GICD_ICFGR(n) (0x0C00 + 4 * ((n) >> 4))
+#define GICD_I_PER_ICFGRn 16
+#define GICD_ICFGR_DEF_TYPE 0
+#define GICD_ICFGR_MASK 0x3
+/* First bit is a polarity bit (0 - low, 1 - high) */
+#define GICD_ICFGR_POL_LOW (0 << 0)
+#define GICD_ICFGR_POL_HIGH (1 << 0)
+#define GICD_ICFGR_POL_MASK 0x1
+/* Second bit is a trigger bit (0 - level, 1 - edge) */
+#define GICD_ICFGR_TRIG_LVL (0 << 1)
+#define GICD_ICFGR_TRIG_EDGE (1 << 1)
+#define GICD_ICFGR_TRIG_MASK 0x2
+
+/*
+ * Software Generated Interrupt Register, GICD_SGIR
+ */
+#define GICD_SGIR 0x0F00
+#define GICD_SGI_TARGET_SHIFT 16
+#define GICD_SGI_TARGET_MASK 0xff
+#define GICD_SGI_FILTER_SHIFT 24
+#define GICD_SGI_FILTER_MASK 0x3
+#define GICD_SGI_MAX_INITID 15
+#define GICD_PPI_START
+
+/*
+ * Forward the interrupt to the CPU interfaces specified in the
+ * CPUTargetList field
+ */
+#define GICD_SGI_FILTER_TO_LIST 0x0
+/*
+ * Forward the interrupt to all CPU interfaces except that of the
+ * processor that requested the interrupt.
+ */
+#define GICD_SGI_FILTER_TO_OTHERS 0x1
+/*
+ * Forward the interrupt only to the CPU interface of the processor
+ * that requested the interrupt.
+ */
+#define GICD_SGI_FILTER_TO_SELF 0x2
+
+/*
+ * SGI Clear-Pending Registers, GICD_CPENDSGIRn
+ * Provide a clear-pending bit for each supported SGI and source
+ * processor combination. When a processor writes a 1 to a clear-pending
+ * bit, the pending state of the corresponding SGI for the corresponding
+ * source processor is removed, and no longer targets the processor
+ * performing the write. Writing a 0 has no effect. Reading a bit identifies
+ * whether the SGI is pending, from the corresponding source processor, on
+ * the reading processor.
+ */
+#define GICD_CPENDSGIRn (0x0F10 + 4 *((n) >> 2))
+#define GICD_I_PER_CPENDSGIRn 4
+
+/*
+ * SGI Set-Pending Registers, GICD_SPENDSGIRn
+ * Provide a set-pending bit for each supported SGI and source processor
+ * combination. When a processor writes a 1 to a set-pending bit, the pending
+ * state is applied to the corresponding SGI for the corresponding source
+ * processor. Writing a 0 has no effect. Reading a bit identifies whether
+ * the SGI is pending, from the corresponding source processor, on the
+ * reading processor.
+ */
+#define GICD_SPENDSGIRn (0x0F20 + 4 *((n) >> 2))
+#define GICD_I_PER_SPENDSGIRn 4
+
+
+/*
+ * CPU interface registers. Unikraft only support run on non-secure
+ * so we just describe non-secure registers.
+ */
+
+/* CPU Interface Control Register */
+#define GICC_CTLR 0x0000
+#define GICC_CTLR_ENABLE 0x1
+
+/* Interrupt Priority Mask Register */
+#define GICC_PMR 0x0004
+#define GICC_PMR_PRIO_MAX 255
+
+/* Binary Point Register */
+#define GICC_BPR 0x0008
+
+/* Interrupt Acknowledge Register */
+#define GICC_IAR 0x000C
+#define GICC_IAR_INTID_MASK 0x3FF
+#define GICC_IAR_INTID_SPURIOUS 1023
+
+/* End of Interrupt Register */
+#define GICC_EOIR 0x0010
+
+/* Running Priority Register */
+#define GICC_RPR 0x0014
+
+/* Highest Priority Pending Interrupt Register */
+#define GICC_HPPIR 0x0018
+
+/* Aliased Binary Point Register */
+#define GICC_ABPR 0x001C
+
+/* CPU Interface Identification Register */
+#define GICC_IIDR 0x00FC
+
+/* Deactivate Interrupt Register */
+#define GICC_DIR 0x1000
+
+/*
+ * Acknowledging irq equals reading GICC_IAR also
+ * get the intrrupt ID as the side effect.
+ */
+uint32_t gic_ack_irq(void);
+
+/*
+ * write to GICC_EOIR to inform cpu interface completation
+ * of interrupt processing. If GICC_CTLR.EOImode sets to 1
+ * this func just gets priority drop.
+ */
+void gic_eoi_irq(uint32_t irq);
+
+/*
+ * Forward the SIG to the CPU interfaces specified in the
+ * targetlist. Targetlist is a 8-bit bitmap for 0~7 CPU.
+ */
+void gic_sgi_gen_to_list(uint32_t sgintid, uint8_t targetlist);
+
+/*
+ * Forward the SGI to all CPU interfaces except that of the
+ * processor that requested the interrupt.
+ */
+void gic_sgi_gen_to_others(uint32_t sgintid);
+
+/*
+ * Forward the SGI only to the CPU interface of the processor
+ * that requested the interrupt.
+ */
+void gic_sgi_gen_to_self(uint32_t sgintid);
+
+/*
+ * set target cpu for irq in distributor,
+ * @target: bitmask value, bit 1 indicates target to
+ * corresponding cpu interface
+ */
+void gic_set_irq_target(uint32_t irq, uint8_t target);
+
+/* set priority for irq in distributor */
+void gic_set_irq_prio(uint32_t irq, uint8_t priority);
+
+/*
+ * Enable an irq in distributor, each irq occupies one bit
+ * to configure in corresponding registor
+ */
+void gic_enable_irq(uint32_t irq);
+
+/*
+ * Disable an irq in distributor, one bit reserved for an irq
+ * to configure in corresponding register
+ */
+void gic_disable_irq(uint32_t irq);
+
+/*
+ * set pending state for an irq in distributor, one bit
+ * reserved for an irq to configure in corresponding register
+ */
+void gic_set_irq_pending(uint32_t irq);
+
+/*
+ * clear pending state for an irq in distributor, one bit
+ * reserved for an irq to configure in corresponding register
+ */
+void gic_clear_irq_pending(uint32_t irq);
+
+/*
+ * inspect that if an irq is in pending state, every bit
+ * holds the value for the corresponding irq
+ */
+int gic_is_irq_pending(uint32_t irq);
+
+/* set active state for an irq in distributor */
+void gic_set_irq_active(uint32_t irq);
+
+/* clear active state for an irq in distributor */
+void gic_clear_irq_active(uint32_t irq);
+
+/*
+ * inspect that if an irq is in active state,
+ * every bit holds the value for an irq
+ */
+int gic_is_irq_active(uint32_t irq);
+
+/* Config intrrupt trigger type and polarity */
+void gic_set_irq_type(uint32_t irq, int trigger, int polarity);
+
+/* Initialize GICv2 from device tree */
+int _dtb_init_gic(void *dtb);
+
+/* Max CPU interface for GICv2 */
+#define GIC_MAX_CPUIF 8
+
+/* SPI interrupt base ID */
+#define GIC_SPI_BASE 32
+
+/* PPI interrupt base ID */
+#define GIC_PPI_BASE 16
+
+/* Max support interrupt number for GICv2 */
+#define GIC_MAX_IRQ 1020
+
+#endif //__PLAT_CMN_ARM_GICV2_H__
diff --git a/plat/common/include/irq.h b/plat/common/include/irq.h
index edaccfe..c36d004 100644
--- a/plat/common/include/irq.h
+++ b/plat/common/include/irq.h
@@ -43,5 +43,20 @@
#error "Add irq.h for current architecture."
#endif
+/* define IRQ trigger types */
+enum uk_irq_trigger {
+ UK_IRQ_TRIGGER_NONE = 0,
+ UK_IRQ_TRIGGER_EDGE = 1,
+ UK_IRQ_TRIGGER_LEVEL = 2,
+ UK_IRQ_TRIGGER_MAX
+};
+
+/* define IRQ trigger polarities */
+enum uk_irq_polarity {
+ UK_IRQ_POLARITY_NONE = 0,
+ UK_IRQ_POLARITY_HIGH = 1,
+ UK_IRQ_POLARITY_LOW = 2,
+ UK_IRQ_POLARITY_MAX
+};
#endif /* __PLAT_CMN_IRQ_H__ */
diff --git a/plat/kvm/Makefile.uk b/plat/kvm/Makefile.uk
index 197175a..572f4c3 100644
--- a/plat/kvm/Makefile.uk
+++ b/plat/kvm/Makefile.uk
@@ -61,6 +61,7 @@ LIBKVMPLAT_SRCS-$(CONFIG_ARCH_ARM_64) +=
$(UK_PLAT_COMMON_BASE)/arm/time.c|commo
LIBKVMPLAT_SRCS-$(CONFIG_ARCH_ARM_64) +=
$(UK_PLAT_COMMON_BASE)/arm/traps.c|common
LIBKVMPLAT_SRCS-$(CONFIG_ARCH_ARM_64) +=
$(UK_PLAT_COMMON_BASE)/arm/fdt.c|common
LIBKVMPLAT_SRCS-$(CONFIG_ARCH_ARM_64) +=
$(UK_PLAT_COMMON_BASE)/arm/rtc.c|common
+LIBKVMPLAT_SRCS-$(CONFIG_ARCH_ARM_64) +=
$(UK_PLAT_COMMON_BASE)/arm/gic-v2.c|common
LIBKVMPLAT_SRCS-$(CONFIG_ARCH_ARM_64) += $(LIBKVMPLAT_BASE)/arm/entry64.S
LIBKVMPLAT_SRCS-$(CONFIG_ARCH_ARM_64) += $(LIBKVMPLAT_BASE)/arm/exceptions.S
LIBKVMPLAT_SRCS-$(CONFIG_ARCH_ARM_64) += $(LIBKVMPLAT_BASE)/arm/pagetable.S
diff --git a/plat/kvm/arm/setup.c b/plat/kvm/arm/setup.c
index 09530bb..14e64ad 100644
--- a/plat/kvm/arm/setup.c
+++ b/plat/kvm/arm/setup.c
@@ -18,18 +18,16 @@
* NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
+#include <limits.h>
#include <libfdt.h>
-#include <kvm/console.h>
+#include <uk/essentials.h>
#include <uk/assert.h>
+#include <kvm/console.h>
#include <kvm-arm/mm.h>
#include <arm/cpu.h>
-#include <uk/arch/limits.h>
-
-void *_libkvmplat_pagetable;
-void *_libkvmplat_heap_start;
-void *_libkvmplat_stack_top;
-void *_libkvmplat_mem_end;
-void *_libkvmplat_dtb;
+#include <arm/rtc.h>
+#include <arm/gic-v2.h>
+#include <arm/fdt.h>
#define MAX_CMDLINE_SIZE 1024
static char cmdline[MAX_CMDLINE_SIZE];
@@ -47,7 +45,7 @@ static void _init_dtb(void *dtb_pointer)
UK_CRASH("Invalid DTB: %s\n", fdt_strerror(ret));
_libkvmplat_dtb = dtb_pointer;
- uk_pr_info("Found device tree on: %p\n", dtb_pointer);
+ uk_printd(DLVL_INFO, "Found device tree on: %p\n", dtb_pointer);
}
static void _dtb_get_psci_method(void)
@@ -65,13 +63,13 @@ static void _dtb_get_psci_method(void)
fdtpsci = fdt_node_offset_by_compatible(_libkvmplat_dtb,
-1, "arm,psci-0.2");
if (fdtpsci < 0) {
- uk_pr_info("No PSCI conduit found in DTB\n");
+ uk_printd(DLVL_INFO, "No PSCI conduit found in DTB\n");
goto enomethod;
}
fdtmethod = fdt_getprop(_libkvmplat_dtb, fdtpsci, "method", &len);
if (!fdtmethod || (len <= 0)) {
- uk_pr_info("No PSCI method found\n");
+ uk_printd(DLVL_INFO, "No PSCI method found\n");
goto enomethod;
}
@@ -80,16 +78,16 @@ static void _dtb_get_psci_method(void)
else if (!strcmp(fdtmethod, "smc"))
smcc_psci_call = smcc_psci_smc_call;
else {
- uk_pr_info("Invalid PSCI conduit method: %s\n",
- fdtmethod);
+ uk_printd(DLVL_INFO,
+ "Invalid PSCI conduit method: %s\n", fdtmethod);
goto enomethod;
}
- uk_pr_info("PSCI method: %s\n", fdtmethod);
+ uk_printd(DLVL_INFO, "PSCI method: %s\n", fdtmethod);
return;
enomethod:
- uk_pr_info("Support PSCI from PSCI-0.2\n");
+ uk_printd(DLVL_INFO, "Support PSCI from PSCI-0.2\n");
smcc_psci_call = NULL;
}
@@ -104,13 +102,13 @@ static void _init_dtb_mem(void)
/* search for assigned VM memory in DTB */
if (fdt_num_mem_rsv(_libkvmplat_dtb) != 0)
- uk_pr_warn("Reserved memory is not supported\n");
+ uk_printd(DLVL_WARN, "Reserved memory is not supported\n");
fdt_mem = fdt_node_offset_by_prop_value(_libkvmplat_dtb, -1,
"device_type",
"memory", sizeof("memory"));
if (fdt_mem < 0) {
- uk_pr_warn("No memory found in DTB\n");
+ uk_printd(DLVL_WARN, "No memory found in DTB\n");
return;
}
@@ -138,7 +136,8 @@ static void _init_dtb_mem(void)
/* If we have more than one memory bank, give a warning messasge */
if (prop_len > prop_min_len)
- uk_pr_warn("Currently, we support only one memory bank!\n");
+ uk_printd(DLVL_WARN,
+ "Currently, we support only one memory bank!\n");
mem_base = fdt64_to_cpu(regs[0]);
mem_size = fdt64_to_cpu(regs[1]);
@@ -172,17 +171,25 @@ static void _dtb_get_cmdline(char *cmdline, size_t maxlen)
cmdline[((unsigned int) len - 1) <= (maxlen - 1) ?
((unsigned int) len - 1) : (maxlen - 1)] = '\0';
- uk_pr_info("Command line: %s\n", cmdline);
+ uk_printd(DLVL_INFO, "Command line: %s\n", cmdline);
return;
enocmdl:
- uk_pr_info("No command line found\n");
+ uk_printd(DLVL_INFO, "No command line found\n");
strcpy(cmdline, CONFIG_UK_NAME);
}
static void _libkvmplat_entry2(void *arg __attribute__((unused)))
{
- ukplat_entry_argp(NULL, (char *)cmdline, strlen(cmdline));
+ /* After switch to new stack, we start initializing other devices */
+
+ /* Initialize GIC interrupt controller */
+ _dtb_init_gic(_libkvmplat_dtb);
+
+ /* Initialize RTC */
+ _dtb_init_rtc(_libkvmplat_dtb);
+
+ ukplat_entry_argp(NULL, (char *)cmdline, strlen(cmdline));
}
void _libkvmplat_start(void *dtb_pointer)
@@ -190,7 +197,7 @@ void _libkvmplat_start(void *dtb_pointer)
_init_dtb(dtb_pointer);
_libkvmplat_init_console();
- uk_pr_info("Entering from KVM (arm64)...\n");
+ uk_printd(DLVL_INFO, "Entering from KVM (arm64)...\n");
/* Get command line from DTB */
@@ -202,15 +209,15 @@ void _libkvmplat_start(void *dtb_pointer)
/* Initialize memory from DTB */
_init_dtb_mem();
- uk_pr_info("pagetable start: %p\n", _libkvmplat_pagetable);
- uk_pr_info(" heap start: %p\n", _libkvmplat_heap_start);
- uk_pr_info(" stack top: %p\n", _libkvmplat_stack_top);
+ uk_printd(DLVL_INFO, "pagetable start: %p\n", _libkvmplat_pagetable);
+ uk_printd(DLVL_INFO, " heap start: %p\n", _libkvmplat_heap_start);
+ uk_printd(DLVL_INFO, " stack top: %p\n", _libkvmplat_stack_top);
/*
* Switch away from the bootstrap stack as early as possible.
*/
- uk_pr_info("Switch from bootstrap stack to stack @%p\n",
- _libkvmplat_stack_top);
+ uk_printd(DLVL_INFO, "Switch from bootstrap stack to stack @%p\n",
+ _libkvmplat_stack_top);
_libkvmplat_newstack((uint64_t) _libkvmplat_stack_top,
_libkvmplat_entry2, NULL);
--
2.7.4
_______________________________________________
Minios-devel mailing list
Minios-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/minios-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |