|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Xen-devel] Experimental results for VGA passthrough
Hi Beng, Would you please send the patch you applied on top of Xen to the list? I think many people are interested in that. Thanks, Jun On Sun, Jun 7, 2009 at 12:07 PM, Beng Heng, Ng<bengheng@xxxxxxxxxxxxxx> wrote: > I tried setting ATI as the primary adapter and passing it through to > DomU again. Seems to work pretty well after I install the ATI driver > over remote desktop. > > I'm using ATI HD2600XT. The Radeon driver says version 9.5. > > Beng Heng > > Jean Guyader wrote: >> ATI driver does'nt support pass through with vt-d, so I think there is >> a very small that you can make it work. >> Did you try to install the ATI driver inside the domU using RDP? >> >> Jean >> >> 2009/6/4 Beng Heng, Ng <bengheng@xxxxxxxxxxxxxx>: >>> Hi Jean, >>> >>> Thanks for the reply. I disabled the assertion and upon calling xm >>> create on DomU, the screen blanks out shortly (about 3 seconds) than >>> reappears with a tinge of yellow (about 3 seconds too), and finally >>> becomes blank totally. You can almost imagine it to be different stages >>> of DomU (WXP in my case) booting. I was able to RDP into DomU. Shutting >>> down DomU does not return the screen to Dom0. The log is attached. >>> >>> - Beng Heng >>> >>> __ __ _____ _ _ _ _ >>> \ \/ /___ _ __ |___ /| || | / | _ __ ___/ | _ __ _ __ ___ >>> \ // _ \ '_ \ |_ \| || |_ | |__| '__/ __| |__| '_ \| '__/ _ \ >>> / \ __/ | | | ___) |__ _|| |__| | | (__| |__| |_) | | | __/ >>> /_/\_\___|_| |_| |____(_) |_|(_)_| |_| \___|_| | .__/|_| \___| >>> |_| >>> (XEN) Xen version 3.4.1-rc1-pre (root@xxxxxxxxxxx) (gcc version 4.3.2 >>> 20081105 (Red Hat 4.3.2-7) (GCC) ) Thu Jun 4 13:49:51 EDT 2009 >>> (XEN) Latest ChangeSet: Mon Jun 01 14:56:17 2009 +0100 19628:29d7e3522cc5 >>> (XEN) Command line: loglvl=all guest_loglvl=all dom0_mem=1G com1=115200,8n1 >>> console=com1 iommu=1 >>> (XEN) Video information: >>> (XEN) VGA is text mode 80x25, font 8x16 >>> (XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds >>> (XEN) Disc information: >>> (XEN) Found 0 MBR signatures >>> (XEN) Found 1 EDD information structures >>> (XEN) Xen-e820 RAM map: >>> (XEN) 0000000000000000 - 000000000009e800 (usable) >>> (XEN) 000000000009e800 - 00000000000a0000 (reserved) >>> (XEN) 00000000000e0000 - 0000000000100000 (reserved) >>> (XEN) 0000000000100000 - 000000007d6c1000 (usable) >>> (XEN) 000000007d6c1000 - 000000007d704000 (ACPI NVS) >>> (XEN) 000000007d704000 - 000000007d826000 (reserved) >>> (XEN) 000000007d826000 - 000000007d83a000 (ACPI NVS) >>> (XEN) 000000007d83a000 - 000000007d93c000 (reserved) >>> (XEN) 000000007d93c000 - 000000007d93d000 (ACPI NVS) >>> (XEN) 000000007d93d000 - 000000007d942000 (reserved) >>> (XEN) 000000007d942000 - 000000007d94c000 (ACPI data) >>> (XEN) 000000007d94c000 - 000000007d967000 (ACPI NVS) >>> (XEN) 000000007d967000 - 000000007d986000 (reserved) >>> (XEN) 000000007d986000 - 000000007d98c000 (ACPI NVS) >>> (XEN) 000000007d98c000 - 000000007db00000 (usable) >>> (XEN) 000000007dc00000 - 0000000080000000 (reserved) >>> (XEN) 00000000fed1c000 - 00000000fed20000 (reserved) >>> (XEN) 00000000ff000000 - 0000000100000000 (reserved) >>> (XEN) 0000000100000000 - 000000017c000000 (usable) >>> (XEN) System RAM: 3991MB (4087628kB) >>> (XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL) >>> (XEN) ACPI: XSDT 7D94AE18, 005C (r1 INTEL DQ45CB 4F MSFT 10013) >>> (XEN) ACPI: FACP 7D949D98, 00F4 (r4 INTEL A M I 6222004 MSFT 10013) >>> (XEN) ACPI: DSDT 7D942018, 6818 (r1 INTEL DQ45CB 4F INTL 20051117) >>> (XEN) ACPI: FACS 7D952F40, 0040 >>> (XEN) ACPI: APIC 7D949F18, 006C (r2 INTEL DQ45CB 4F MSFT 10013) >>> (XEN) ACPI: MCFG 7D954E18, 003C (r1 INTEL DQ45CB 4F MSFT 97) >>> (XEN) ACPI: ASF! 7D953D18, 00A0 (r32 INTEL DQ45CB 4F TFSM F4240) >>> (XEN) ACPI: SPCR 7D954D18, 0050 (r1 INTEL DQ45CB 4F AMI. 3) >>> (XEN) ACPI: TCPA 7D954C98, 0032 (r2 INTEL DQ45CB 4F MSFT 1000013) >>> (XEN) ACPI: DMAR 7D93CC18, 0110 (r1 INTEL DQ45CB 4F INTL 1) >>> (XEN) NUMA turned off >>> (XEN) Faking a node at 0000000000000000-000000017c000000 >>> (XEN) Domain heap initialised >>> (XEN) DMI 2.4 present. >>> (XEN) Using APIC driver default >>> (XEN) ACPI: PM-Timer IO Port: 0x408 >>> (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0] >>> (XEN) ACPI: wakeup_vec[7d952f4c], vec_size[20] >>> (XEN) ACPI: Local APIC address 0xfee00000 >>> (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) >>> (XEN) Processor #0 7:7 APIC version 20 >>> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) >>> (XEN) Processor #1 7:7 APIC version 20 >>> (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) >>> (XEN) Processor #2 7:7 APIC version 20 >>> (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) >>> (XEN) Processor #3 7:7 APIC version 20 >>> (XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0]) >>> (XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23 >>> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) >>> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) >>> (XEN) ACPI: IRQ0 used by override. >>> (XEN) ACPI: IRQ2 used by override. >>> (XEN) ACPI: IRQ9 used by override. >>> (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs >>> (XEN) [VT-D]dmar.c:485: Host address width 36 >>> (XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD >>> (XEN) [VT-D]dmar.c:349: dmaru->address = fed90000 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0 >>> (XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD >>> (XEN) [VT-D]dmar.c:349: dmaru->address = fed91000 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0 >>> (XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD >>> (XEN) [VT-D]dmar.c:349: dmaru->address = fed92000 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3 >>> (XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD >>> (XEN) [VT-D]dmar.c:349: dmaru->address = fed93000 >>> (XEN) [VT-D]dmar.c:358: found INCLUDE_ALL >>> (XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2 >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7 >>> (XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR >>> (XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0 >>> (XEN) Intel VT-d DMAR tables have been parsed. >>> (XEN) Using ACPI (MADT) for SMP configuration information >>> (XEN) Using scheduler: SMP Credit Scheduler (credit) >>> (XEN) Initializing CPU#0 >>> (XEN) Detected 2499.760 MHz processor. >>> (XEN) CPU: L1 I cache: 32K, L1 D cache: 32K >>> (XEN) CPU: L2 cache: 3072K >>> (XEN) CPU: Physical Processor ID: 0 >>> (XEN) CPU: Processor Core ID: 0 >>> (XEN) VMX: Supported advanced features: >>> (XEN) - APIC MMIO access virtualisation >>> (XEN) - APIC TPR shadow >>> (XEN) - Virtual NMI >>> (XEN) - MSR direct-access bitmap >>> (XEN) HVM: VMX enabled >>> (XEN) Intel machine check reporting enabled on CPU#0. >>> (XEN) CPU0: Thermal monitoring enabled (TM2) >>> (XEN) CMCI: CPU0 has no CMCI support >>> (XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9300 @ 2.50GHz stepping 07 >>> (XEN) Booting processor 1/1 eip 8c000 >>> (XEN) Initializing CPU#1 >>> (XEN) CPU: L1 I cache: 32K, L1 D cache: 32K >>> (XEN) CPU: L2 cache: 3072K >>> (XEN) CPU: Physical Processor ID: 0 >>> (XEN) CPU: Processor Core ID: 1 >>> (XEN) Intel machine check reporting enabled on CPU#1. >>> (XEN) CPU1: Thermal monitoring enabled (TM2) >>> (XEN) CMCI: CPU1 has no CMCI support >>> (XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9300 @ 2.50GHz stepping 07 >>> (XEN) Booting processor 2/2 eip 8c000 >>> (XEN) Initializing CPU#2 >>> (XEN) CPU: L1 I cache: 32K, L1 D cache: 32K >>> (XEN) CPU: L2 cache: 3072K >>> (XEN) CPU: Physical Processor ID: 0 >>> (XEN) CPU: Processor Core ID: 2 >>> (XEN) Intel machine check reporting enabled on CPU#2. >>> (XEN) CPU2: Thermal monitoring enabled (TM2) >>> (XEN) CMCI: CPU2 has no CMCI support >>> (XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9300 @ 2.50GHz stepping 07 >>> (XEN) Booting processor 3/3 eip 8c000 >>> (XEN) Initializing CPU#3 >>> (XEN) CPU: L1 I cache: 32K, L1 D cache: 32K >>> (XEN) CPU: L2 cache: 3072K >>> (XEN) CPU: Physical Processor ID: 0 >>> (XEN) CPU: Processor Core ID: 3 >>> (XEN) Intel machine check reporting enabled on CPU#3. >>> (XEN) CPU3: Thermal monitoring enabled (TM2) >>> (XEN) CMCI: CPU3 has no CMCI support >>> (XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9300 @ 2.50GHz stepping 07 >>> (XEN) Total of 4 processors activated. >>> (XEN) ENABLING IO-APIC IRQs >>> (XEN) -> Using new ACK method >>> (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 >>> (XEN) checking TSC synchronization across 4 CPUs: passed. >>> (XEN) Platform timer is 3.579MHz ACPI PM Timer >>> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed >>> (XEN) Brought up 4 CPUs >>> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU3 resumed >>> (XEN) Intel VT-d Snoop Control not supported. >>> (XEN) Intel VT-d DMA Passthrough not supported. >>> (XEN) Intel VT-d Queued Invalidation not supported. >>> (XEN) Intel VT-d Interrupt Remapping not supported. >>> (XEN) I/O virtualisation enabled >>> (XEN) I/O virtualisation for PV guests disabled >>> (XEN) CPUIDLE: disabled due to no HPET. Force enable with 'cpuidle'. >>> (XEN) ACPI sleep modes: S3 >>> (XEN) mcheck_poll: Machine check polling timer started. >>> (XEN) 'S' pressed -> blowing all shadow tables >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:0.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:2.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:3.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:3.2 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:3.3 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:19.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1a.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1a.1 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1a.2 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1a.7 >>> (XEN) [VT-D]iommu.c:1245:d32767 domain_context_mapping:PCIe: bdf = 0:1b.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1d.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1d.1 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1d.2 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1d.7 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1f.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1f.2 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1f.3 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1f.5 >>> (XEN) [VT-D]iommu.c:1245:d32767 domain_context_mapping:PCIe: bdf = 1:0.0 >>> (XEN) [VT-D]iommu.c:1245:d32767 domain_context_mapping:PCIe: bdf = 1:0.1 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 2:0.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 2:1.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:2.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1d.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1d.1 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1d.2 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1d.7 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1a.0 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1a.1 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1a.2 >>> (XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 0:1a.7 >>> (XEN) [VT-D]iommu.c:620: iommu_enable_translation: iommu->reg = >>> ffff828bfff57000 >>> (XEN) [VT-D]iommu.c:620: iommu_enable_translation: iommu->reg = >>> ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:620: iommu_enable_translation: iommu->reg = >>> ffff828bfff55000 >>> (XEN) [VT-D]iommu.c:620: iommu_enable_translation: iommu->reg = >>> ffff828bfff54000 >>> (XEN) *** LOADING DOMAIN 0 *** >>> (XEN) elf_parse_binary: phdr: paddr=0xffffffff80200000 memsz=0x49ef18 >>> (XEN) elf_parse_binary: phdr: paddr=0xffffffff8069f000 memsz=0xf82b8 >>> (XEN) elf_parse_binary: phdr: paddr=0xffffffff80798000 memsz=0xc0d >>> (XEN) elf_parse_binary: phdr: paddr=0xffffffff8079a000 memsz=0xe2da8 >>> (XEN) elf_parse_binary: memory: 0xffffffff80200000 -> 0xffffffff8087cda8 >>> (XEN) elf_xen_parse_note: GUEST_OS = "linux" >>> (XEN) elf_xen_parse_note: GUEST_VERSION = "2.6" >>> (XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0" >>> (XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 >>> (XEN) elf_xen_parse_note: PADDR_OFFSET = 0xffffffff80000000 >>> (XEN) elf_xen_parse_note: ENTRY = 0xffffffff80200000 >>> (XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80206000 >>> (XEN) elf_xen_parse_note: unknown xen elf note (0xd) >>> (XEN) elf_xen_parse_note: FEATURES = >>> "writable_page_tables|writable_descriptor_tables|auto_translated_physmap|pae_pgdir_above_4gb|supervisor_mode_kernel" >>> (XEN) elf_xen_parse_note: LOADER = "generic" >>> (XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1 >>> (XEN) elf_xen_addr_calc_check: addresses: >>> (XEN) virt_base = 0xffffffff80000000 >>> (XEN) elf_paddr_offset = 0xffffffff80000000 >>> (XEN) virt_offset = 0x0 >>> (XEN) virt_kstart = 0xffffffff80200000 >>> (XEN) virt_kend = 0xffffffff8087cda8 >>> (XEN) virt_entry = 0xffffffff80200000 >>> (XEN) p2m_base = 0xffffffffffffffff >>> (XEN) Xen kernel: 64-bit, lsb, compat32 >>> (XEN) Dom0 kernel: 64-bit, lsb, paddr 0xffffffff80200000 -> >>> 0xffffffff8087cda8 >>> (XEN) PHYSICAL MEMORY ARRANGEMENT: >>> (XEN) Dom0 alloc.: 0000000174000000->0000000176000000 (253952 pages to >>> be allocated) >>> (XEN) VIRTUAL MEMORY ARRANGEMENT: >>> (XEN) Loaded kernel: ffffffff80200000->ffffffff8087cda8 >>> (XEN) Init. ramdisk: ffffffff8087d000->ffffffff80fc0000 >>> (XEN) Phys-Mach map: ffffffff80fc0000->ffffffff811c0000 >>> (XEN) Start info: ffffffff811c0000->ffffffff811c04b4 >>> (XEN) Page tables: ffffffff811c1000->ffffffff811ce000 >>> (XEN) Boot stack: ffffffff811ce000->ffffffff811cf000 >>> (XEN) TOTAL: ffffffff80000000->ffffffff81400000 >>> (XEN) ENTRY ADDRESS: ffffffff80200000 >>> (XEN) Dom0 has maximum 4 VCPUs >>> (XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 -> 0xffffffff8069ef18 >>> (XEN) elf_load_binary: phdr 1 at 0xffffffff8069f000 -> 0xffffffff807972b8 >>> (XEN) elf_load_binary: phdr 2 at 0xffffffff80798000 -> 0xffffffff80798c0d >>> (XEN) elf_load_binary: phdr 3 at 0xffffffff8079a000 -> 0xffffffff807e0088 >>> (XEN) Scrubbing Free RAM: .............................done. >>> (XEN) Xen trace buffers: disabled >>> (XEN) Std. Loglevel: All >>> (XEN) Guest Loglevel: All >>> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input >>> to Xen) >>> (XEN) Freed 128kB init memory. >>> kernel direct mapping tables up to 40800000 @ 11ce000-13d5000 >>> Bootdata ok (command line is root=UUID=c1a25e24-42d5-42ae-b1ec-9475ae1da2b1 >>> ro xencons=ttyS console=tty0 console=ttyS0 pciback.hide=(00:02.0)) >>> Linux version 2.6.18.8-xen0 (root@xxxxxxxxxxxxxxx) (gcc version 4.3.2 >>> 20081105 (Red Hat 4.3.2-7) (GCC) ) #1 SMP Wed Jun 3 20:45:36 EDT 2009 >>> BIOS-provided physical RAM map: >>> Xen: 0000000000000000 - 0000000040800000 (usable) >>> DMI 2.4 present. >>> No mptable found. >>> >>> ERROR: Invalid checksum >>> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) >>> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) >>> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) >>> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) >>> ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0]) >>> IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23 >>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) >>> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) >>> Setting APIC routing to xen >>> Using ACPI (MADT) for SMP configuration information >>> Allocating PCI resources starting at 88000000 (gap: 80000000:7ed1c000) >>> Built 1 zonelists. Total pages: 260580 >>> Kernel command line: root=UUID=c1a25e24-42d5-42ae-b1ec-9475ae1da2b1 ro >>> xencons=ttyS console=tty0 console=ttyS0 pciback.hide=(00:02.0) >>> Initializing CPU#0 >>> PID hash table entries: 4096 (order: 12, 32768 bytes) >>> Xen reported: 2499.716 MHz processor. >>> Console: colour VGA+ 80x25 >>> Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) >>> Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) >>> Software IO TLB enabled: >>> Aperture: 64 megabytes >>> Kernel range: ffff880002407000 - ffff880006407000 >>> Address size: 27 bits >>> PCI-DMA: Using software bounce buffering for IO (SWIOTLB) >>> Memory: 947704k/1056768k available (4024k kernel code, 100700k reserved, >>> 1625k data, 216k init) >>> Calibrating delay using timer specific routine.. 5000.66 BogoMIPS >>> (lpj=25003323) >>> Mount-cache hash table entries: 256 >>> CPU: L1 I cache: 32K, L1 D cache: 32K >>> CPU: L2 cache: 3072K >>> CPU: Physical Processor ID: 0 >>> CPU: Processor Core ID: 0 >>> SMP alternatives: switching to UP code >>> ACPI: Core revision 20060707 >>> SMP alternatives: switching to SMP code >>> Initializing CPU#1 >>> Initializing CPU#2 >>> CPU: L1 I cache: 32K, L1 D cache: 32K >>> CPU: L2 cache: 3072K >>> CPU: Physical Processor ID: 0 >>> CPU: Processor Core ID: 1 >>> Brought up 4 CPUs >>> Initializing CPU#3 >>> CPU: L1 I cache: 32K, L1 D cache: 32K >>> CPU: L2 cache: 3072K >>> CPU: Physical Processor ID: 0 >>> CPU: Processor Core ID: 3 >>> CPU: L1 I cache: 32K, L1 D cache: 32K >>> CPU: L2 cache: 3072K >>> CPU: Physical Processor ID: 0 >>> CPU: Processor Core ID: 2 >>> migration_cost=31 >>> checking if image is initramfs... it is >>> Freeing initrd memory: 7436k freed >>> NET: Registered protocol family 16 >>> ACPI: bus type pci registered >>> PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved >>> PCI: Not using MMCONFIG. >>> PCI: Using configuration type 1 >>> ACPI: Interpreter enabled >>> ACPI: Using IOAPIC for interrupt routing >>> ACPI: PCI Root Bridge [PCI0] (0000:00) >>> PCI: Transparent bridge - 0000:00:1e.0 >>> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *10 11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 10 11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15) >>> ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15) >>> Linux Plug and Play Support v0.97 (c) Adam Belay >>> pnp: PnP ACPI init >>> (XEN) io_apic.c:2139: >>> (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=4 >>> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=000109f1 >>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! >>> pnp: PnP ACPI: found 10 devices >>> xen_mem: Initialising balloon driver. >>> SCSI subsystem initialized >>> usbcore: registered new driver usbfs >>> usbcore: registered new driver hub >>> PCI: Using ACPI for IRQ routing >>> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a >>> report >>> pnp: 00:02: ioport range 0xa20-0xa3f has been reserved >>> pnp: 00:02: ioport range 0xa00-0xa1f has been reserved >>> pnp: 00:02: ioport range 0xb78-0xb7f has been reserved >>> pnp: 00:02: ioport range 0xf78-0xf7f has been reserved >>> pnp: 00:09: ioport range 0x400-0x47f could not be reserved >>> pnp: 00:09: ioport range 0x1180-0x119f has been reserved >>> pnp: 00:09: ioport range 0x500-0x57f has been reserved >>> (XEN) PCI add device 00:00.0 >>> (XEN) PCI add device 00:01.0 >>> (XEN) PCI add device 00:02.0 >>> pciback 0000:00:02.0: seizing device >>> (XEN) PCI add device 00:03.0 >>> (XEN) PCI add device 00:03.2 >>> (XEN) PCI add device 00:03.3 >>> (XEN) PCI add device 00:19.0 >>> (XEN) PCI add device 00:1a.0 >>> (XEN) PCI add device 00:1a.1 >>> (XEN) PCI add device 00:1a.2 >>> (XEN) PCI add device 00:1a.7 >>> (XEN) PCI add device 00:1b.0 >>> (XEN) PCI add device 00:1d.0 >>> (XEN) PCI add device 00:1d.1 >>> (XEN) PCI add device 00:1d.2 >>> (XEN) PCI add device 00:1d.7 >>> (XEN) PCI add device 00:1e.0 >>> (XEN) PCI add device 00:1f.0 >>> (XEN) PCI add device 00:1f.2 >>> (XEN) PCI add device 00:1f.3 >>> (XEN) PCI add device 00:1f.5 >>> (XEN) PCI add device 01:00.0 >>> (XEN) PCI add device 01:00.1 >>> (XEN) PCI add device 02:00.0 >>> (XEN) PCI add device 02:01.0 >>> PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 >>> PCI: Bridge: 0000:00:01.0 >>> IO window: c000-cfff >>> MEM window: c0000000-d00fffff >>> PREFETCH window: disabled. >>> PCI: Bridge: 0000:00:1e.0 >>> IO window: b000-bfff >>> MEM window: d0800000-d08fffff >>> PREFETCH window: 88000000-880fffff >>> GSI 16 sharing vector 0xB0 and IRQ 16 >>> ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 >>> NET: Registered protocol family 2 >>> IP route cache hash table entries: 32768 (order: 6, 262144 bytes) >>> TCP established hash table entries: 131072 (order: 9, 2097152 bytes) >>> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) >>> TCP: Hash tables configured (established 131072 bind 65536) >>> TCP reno registered >>> IA-32 Microcode Update Driver: v1.14a-xen <tigran@xxxxxxxxxxx> >>> Initializing Cryptographic API >>> io scheduler noop registered >>> io scheduler anticipatory registered (default) >>> io scheduler deadline registered >>> io scheduler cfq registered >>> 0000:00:1a.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001 >>> 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001 >>> floppy0: Unable to grab DMA2 for the floppy driver >>> floppy0: no floppy controllers found >>> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize >>> loop: loaded (max 8 devices) >>> HP CISS Driver (v 3.6.10) >>> Intel(R) PRO/1000 Network Driver - version 7.1.9-k4 >>> Copyright (c) 1999-2006 Intel Corporation. >>> (XEN) PCI add device 02:00.0 >>> GSI 17 sharing vector 0xB8 and IRQ 17 >>> ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 21 (level, low) -> IRQ 17 >>> e1000: 0000:02:00.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:34:34:a8 >>> e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection >>> e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k4 >>> e1000e: Copyright (c) 1999-2008 Intel Corporation. >>> (XEN) PCI add device 00:19.0 >>> GSI 18 sharing vector 0xC0 and IRQ 18 >>> ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 18 >>> eth1: (PCI Express:2.5GB/s:Width x1) 00:1c:c0:7d:61:d7 >>> eth1: Intel(R) PRO/1000 Network Connection >>> eth1: MAC: 7, PHY: 8, PBA No: ffffff-0ff >>> pcnet32.c:v1.32 18.Mar.2006 tsbogend@xxxxxxxxxxxxxxxx >>> e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI >>> e100: Copyright(c) 1999-2005 Intel Corporation >>> tun: Universal TUN/TAP device driver, 1.6 >>> tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> >>> Xen virtual console successfully installed as ttyS0 >>> Event-channel device installed. >>> blktap_device_init: blktap device major 254 >>> blktap_ring_init: blktap ring major: 253 >>> netfront: Initialising virtual ethernet driver. >>> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 >>> ACPI: PCI interrupt for device 0000:00:02.0 disabled >>> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 >>> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx >>> (XEN) PCI add device 00:03.2 >>> (XEN) PCI add device 00:1f.5 >>> Adaptec aacraid driver (1.1-5[2409]-mh2) >>> 3ware Storage Controller device driver for Linux v1.26.02.001. >>> (XEN) PCI add device 00:1f.2 >>> GSI 19 sharing vector 0xD0 and IRQ 19 >>> ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 >>> ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA >>> mode >>> ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part >>> ata1: SATA max UDMA/133 cmd 0xFFFFC2000002A100 ctl 0x0 bmdma 0x0 irq 254 >>> ata2: SATA max UDMA/133 cmd 0xFFFFC2000002A180 ctl 0x0 bmdma 0x0 irq 254 >>> ata3: SATA max UDMA/133 cmd 0xFFFFC2000002A200 ctl 0x0 bmdma 0x0 irq 254 >>> ata4: SATA max UDMA/133 cmd 0xFFFFC2000002A280 ctl 0x0 bmdma 0x0 irq 254 >>> ata5: SATA max UDMA/133 cmd 0xFFFFC2000002A300 ctl 0x0 bmdma 0x0 irq 254 >>> ata6: SATA max UDMA/133 cmd 0xFFFFC2000002A380 ctl 0x0 bmdma 0x0 irq 254 >>> scsi0 : ahci >>> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >>> ata1.00: ATA-8, max UDMA/133, 976773168 sectors: LBA48 NCQ (depth 31/32) >>> ata1.00: ata1: dev 0 multi count 16 >>> ata1.00: configured for UDMA/133 >>> scsi1 : ahci >>> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >>> ata2.00: ATAPI, max UDMA/100 >>> ata2.00: configured for UDMA/100 >>> scsi2 : ahci >>> ata3: SATA link down (SStatus 0 SControl 300) >>> scsi3 : ahci >>> ata4: SATA link down (SStatus 0 SControl 300) >>> scsi4 : ahci >>> ata5: SATA link down (SStatus 0 SControl 300) >>> scsi5 : ahci >>> ata6: SATA link down (SStatus 0 SControl 300) >>> Vendor: ATA Model: WDC WD5001AALS-0 Rev: 01.0 >>> Type: Direct-Access ANSI SCSI revision: 05 >>> Vendor: TSSTcorp Model: CDDVDW SH-S223Q Rev: SB00 >>> Type: CD-ROM ANSI SCSI revision: 05 >>> (XEN) PCI add device 00:1f.5 >>> ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] >>> ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 19 >>> ata7: SATA max UDMA/133 cmd 0xD170 ctl 0xD162 bmdma 0xD130 irq 19 >>> ata8: SATA max UDMA/133 cmd 0xD150 ctl 0xD142 bmdma 0xD138 irq 19 >>> scsi6 : ata_piix >>> ATA: abnormal status 0x7F on port 0xD177 >>> scsi7 : ata_piix >>> ATA: abnormal status 0x7F on port 0xD157 >>> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) >>> sda: Write Protect is off >>> SCSI device sda: drive cache: write back >>> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) >>> sda: Write Protect is off >>> SCSI device sda: drive cache: write back >>> sda: sda1 sda2 sda3 sda4 < sda5 sda6 > >>> sd 0:0:0:0: Attached scsi disk sda >>> Fusion MPT base driver 3.04.01 >>> Copyright (c) 1999-2005 LSI Logic Corporation >>> Fusion MPT SPI Host driver 3.04.01 >>> usbmon: debugfs is not available >>> USB Universal Host Controller Interface driver v3.0 >>> (XEN) PCI add device 00:1a.0 >>> ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 >>> uhci_hcd 0000:00:1a.0: UHCI Host Controller >>> uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 >>> uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000d0e0 >>> usb usb1: configuration #1 chosen from 1 choice >>> hub 1-0:1.0: USB hub found >>> hub 1-0:1.0: 2 ports detected >>> (XEN) PCI add device 00:1a.1 >>> ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 17 >>> uhci_hcd 0000:00:1a.1: UHCI Host Controller >>> uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 >>> uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000d0c0 >>> usb usb2: configuration #1 chosen from 1 choice >>> hub 2-0:1.0: USB hub found >>> hub 2-0:1.0: 2 ports detected >>> (XEN) PCI add device 00:1a.2 >>> GSI 20 sharing vector 0x21 and IRQ 20 >>> ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 20 >>> uhci_hcd 0000:00:1a.2: UHCI Host Controller >>> uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3 >>> uhci_hcd 0000:00:1a.2: irq 20, io base 0x0000d0a0 >>> usb usb3: configuration #1 chosen from 1 choice >>> hub 3-0:1.0: USB hub found >>> hub 3-0:1.0: 2 ports detected >>> (XEN) PCI add device 00:1d.0 >>> GSI 21 sharing vector 0x29 and IRQ 21 >>> ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 21 >>> uhci_hcd 0000:00:1d.0: UHCI Host Controller >>> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4 >>> uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000d080 >>> usb usb4: configuration #1 chosen from 1 choice >>> hub 4-0:1.0: USB hub found >>> hub 4-0:1.0: 2 ports detected >>> (XEN) PCI add device 00:1d.1 >>> ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 >>> uhci_hcd 0000:00:1d.1: UHCI Host Controller >>> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5 >>> uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d060 >>> usb usb5: configuration #1 chosen from 1 choice >>> hub 5-0:1.0: USB hub found >>> hub 5-0:1.0: 2 ports detected >>> (XEN) PCI add device 00:1d.2 >>> ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20 >>> uhci_hcd 0000:00:1d.2: UHCI Host Controller >>> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6 >>> uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000d040 >>> usb usb6: configuration #1 chosen from 1 choice >>> hub 6-0:1.0: USB hub found >>> hub 6-0:1.0: 2 ports detected >>> usb 3-1: new full speed USB device using uhci_hcd and address 2 >>> usb 3-1: configuration #1 chosen from 1 choice >>> hub 3-1:1.0: USB hub found >>> hub 3-1:1.0: 4 ports detected >>> usb 3-1.1: new low speed USB device using uhci_hcd and address 3 >>> usb 3-1.1: configuration #1 chosen from 1 choice >>> input: HID 04f3:0801 as /class/input/input0 >>> input: USB HID v1.10 Keyboard [HID 04f3:0801] on usb-0000:00:1a.2-1.1 >>> input: HID 04f3:0801 as /class/input/input1 >>> input: USB HID v1.10 Mouse [HID 04f3:0801] on usb-0000:00:1a.2-1.1 >>> usbcore: registered new driver usbhid >>> /usr/src/xen-3.4-testing.19628.vgapt.2/linux-2.6.18-xen.hg/drivers/usb/input/hid-core.c: >>> v2.6:USB HID core driver >>> PNP: No PS/2 controller found. Probing ports directly. >>> serio: i8042 AUX port at 0x60,0x64 irq 12 >>> serio: i8042 KBD port at 0x60,0x64 irq 1 >>> mice: PS/2 mouse device common for all mice >>> md: raid0 personality registered for level 0 >>> md: raid1 personality registered for level 1 >>> md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 >>> md: bitmap version 4.39 >>> device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: >>> dm-devel@xxxxxxxxxx >>> TCP bic registered >>> NET: Registered protocol family 1 >>> NET: Registered protocol family 17 >>> Bridge firewalling registered >>> PCI IO multiplexer device installed. >>> ACPI: (supports S0 S1 S3 S4 S5) >>> BIOS EDD facility v0.16 2004-Jun-25, 1 devices found >>> Freeing unused kernel memory: 216k freed >>> Mounting proc filesystem >>> Mounting sysfs filesystem >>> Creating /dev >>> Creating initial device nodes >>> Loading /lib/kbd/keymaps/i386/qwerty/us.map >>> Setting up hotplug. >>> Creating block device nodes. >>> Creating character device nodes. >>> Creating root device. >>> Mounting root filesystem. >>> EXT3-fs: INFO: recovery required on readonly filesystem. >>> EXT3-fs: write access will be enabled during recovery. >>> kjournald starting. Commit interval 5 seconds >>> EXT3-fs: recovery complete. >>> EXT3-fs: mounted filesystem with ordered data mode. >>> Setting up other filesystems. >>> Switching to new root and running init. >>> Welcome to Fedora >>> Press 'I' to enter interactive startup. >>> Starting udev: G[ OK ] >>> Setting hostname xxx.xxx.xxx.xxx: [ OK ] >>> Jun 04 14:11:00 | DM multipath kernel driver not loaded >>> Setting up Logical Volume Management: File descriptor 7 left open >>> [ OK ] >>> Checking filesystems >>> Checking all file systems. >>> [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda2 >>> /: clean, 2579449/6111232 files, 12471163/24418800 blocks >>> [ OK ] >>> Remounting root filesystem in read-write mode: [ OK ] >>> Mounting local filesystems: mount: special device UUID=4405-A494 does not >>> exist >>> FATAL: Module fuse not found. >>> ntfs-3g-mount: fuse device is missing, try 'modprobe fuse' as root >>> [FAILED] >>> Enabling local filesystem quotas: quotaon: Warning: No quota format >>> detected in the kernel. >>> [ OK ] >>> Enabling /etc/fstab swaps: swapon: /proc/swaps: unexpected file format >>> [ OK ] >>> Entering non-interactive startup >>> Applying Intel CPU microcode update: FATAL: Module microcode not found. >>> [ OK ]ERROR: Module microcode does not exist in /proc/modules >>> >>> ip6tables: Applying firewall rules: FATAL: Module ip6_tables not found. >>> ip6tables-restore v1.4.1.1: ip6tables-restore: unable to initialize table >>> 'filter' >>> >>> Error occurred at line: 3 >>> Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more >>> information. >>> [FAILED] >>> iptables: Applying firewall rules: FATAL: Module ip_tables not found. >>> iptables-restore v1.4.1.1: iptables-restore: unable to initialize table >>> 'filter' >>> >>> Error occurred at line: 3 >>> Try `iptables-restore -h' or 'iptables-restore --help' for more information. >>> [FAILED] >>> Starting auditd: [FAILED] >>> Starting system logger: [ OK ] >>> Starting irqbalance: [ OK ] >>> Starting rpcbind: [ OK ] >>> Starting NFS statd: [FAILED] >>> Starting RPC idmapd: FATAL: Module sunrpc not found. >>> FATAL: Error running install command for sunrpc >>> Error: RPC MTAB does not exist. >>> Starting system message bus: [ OK ] >>> Starting HAL daemon: [ OK ] >>> Setting network parameters... [ OK ] >>> Starting NetworkManager daemon: [ OK ] >>> Starting portreserve: [ OK ] >>> Starting Bluetooth services:[ OK ] >>> Starting sendmail: [ OK ] >>> Starting sm-client: [ OK ] >>> Starting console mouse services: [ OK ] >>> Starting httpd: [ OK ] >>> Starting crond: [ OK ][ OK ] >>> Starting kerneloops:[ OK ] >>> Starting atd: [ OK ][ OK ] >>> Starting Avahi daemon... [ OK ] >>> Starting cups: [ OK ] >>> Starting anacron: [ OK ] >>> Starting sshd: [ OK ] >>> >>> Fedora release 10 (Cambridge) >>> Kernel 2.6.18.8-xen0 on an x86_64 (ttyS0) >>> >>> xxx.xxx.xxx.xxx login: (XEN) [VT-D]iommu.c:1364:d0 >>> domain_context_unmap:PCI: bdf = 0:2.0 >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:1252:d0 domain_context_mapping:PCI: bdf = 0:2.0 >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 7e000000 REASON >>> 2 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 7e000 >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 1f0 >>> (XEN) l2[1f0] = 0 >>> (XEN) l2[1f0] not present >>> (XEN) [VT-D]iommu.c:1252:d0 domain_context_mapping:PCI: bdf = 0:2.0 >>> (XEN) [VT-D]io.c:251:d0 VT-d irq bind: m_irq = 10 device = 2 intx = 0 >>> (XEN) domctl.c:886:d0 ioport_map:add f_gport=3b0 f_mport=3b0 np=b >>> (XEN) domctl.c:886:d0 ioport_map:add f_gport=3c0 f_mport=3c0 np=20 >>> (XEN) domctl.c:835:d0 memory_map:add: gfn=a0 mfn=a0 nr_mfns=20 >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 6c1ba000 REASON >>> 5 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 6c1ba >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 160 >>> (XEN) l2[160] = 0 >>> (XEN) l2[160] not present >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 6c1ba000 REASON >>> 5 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 6c1ba >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 160 >>> (XEN) l2[160] = 0 >>> (XEN) l2[160] not present >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 6c1ba000 REASON >>> 5 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 6c1ba >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 160 >>> (XEN) l2[160] = 0 >>> (XEN) l2[160] not present >>> (XEN) HVM1: HVM Loader >>> (XEN) HVM1: Detected Xen v3.4.1-rc1-pre >>> (XEN) HVM1: CPU speed is 2500 MHz >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 6c1ba000 REASON >>> 5 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 6c1ba >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 160 >>> (XEN) l2[160] = 0 >>> (XEN) l2[160] not present >>> (XEN) irq.c:243: Dom1 PCI link 0 changed 0 -> 5 >>> (XEN) HVM1: PCI-ISA link 0 routed to IRQ5 >>> (XEN) irq.c:243: Dom1 PCI link 1 changed 0 -> 10 >>> (XEN) HVM1: PCI-ISA link 1 routed to IRQ10 >>> (XEN) irq.c:243: Dom1 PCI link 2 changed 0 -> 11 >>> (XEN) HVM1: PCI-ISA link 2 routed to IRQ11 >>> (XEN) irq.c:243: Dom1 PCI link 3 changed 0 -> 5 >>> (XEN) HVM1: PCI-ISA link 3 routed to IRQ5 >>> (XEN) HVM1: pci dev 01:3 INTA->IRQ10 >>> (XEN) HVM1: pci dev 02:0 INTA->IRQ11 >>> (XEN) HVM1: pci dev 03:0 INTA->IRQ5 >>> (XEN) HVM1: pci dev 04:0 INTA->IRQ5 >>> (XEN) HVM1: pci dev 02:0 bar 18 size 10000000: e000000c >>> (XEN) domctl.c:835:d0 memory_map:add: gfn=e0000 mfn=b0000 nr_mfns=10000 >>> (XEN) HVM1: pci dev 03:0 bar 14 size 01000000: f0000008 >>> (XEN) domctl.c:835:d0 memory_map:add: gfn=f1000 mfn=d0400 nr_mfns=400 >>> (XEN) HVM1: pci dev 02:0 bar 10 size 00400000: f1000004 >>> (XEN) HVM1: pci dev 03:0 bar 10 size 00000100: 0000c001 >>> (XEN) HVM1: pci dev 04:0 bar 10 size 00000100: 0000c101 >>> (XEN) HVM1: pci dev 04:0 bar 14 size 00000100: f1400000 >>> (XEN) HVM1: pci dev 01:1 bar 20 size 00000010: 0000c201 >>> (XEN) HVM1: pci dev 02:0 bar 20 size 00000008: 0000c211 >>> (XEN) domctl.c:886:d0 ioport_map:add f_gport=c210 f_mport=d220 np=8 >>> (XEN) HVM1: Multiprocessor initialisation: >>> (XEN) HVM1: - CPU0 ... 36-bit phys ... fixed MTRRs ... var MTRRs [3/8] ... >>> done. >>> (XEN) HVM1: Testing HVM environment: >>> (XEN) HVM1: - REP INSB across page boundaries ... passed >>> (XEN) HVM1: Passed 1/1 tests >>> (XEN) HVM1: Writing SMBIOS tables ... >>> (XEN) HVM1: Loading ROMBIOS ... >>> (XEN) HVM1: 9788 bytes of ROMBIOS high-memory extensions: >>> (XEN) HVM1: Relocating to 0xfc000000-0xfc00263c ... done >>> (XEN) HVM1: Creating MP tables ... >>> (XEN) HVM1: No emulated VGA adaptor ... >>> (XEN) HVM1: Loading PCI Option ROM ... >>> (XEN) HVM1: - Manufacturer: http://etherboot.org >>> (XEN) HVM1: - Product name: gPXE >>> (XEN) HVM1: Loading ACPI ... >>> (XEN) HVM1: - Lo data: 000ea020-000ea04f >>> (XEN) HVM1: - Hi data: fc002800-fc005c9f >>> (XEN) HVM1: vm86 TSS at fc006000 >>> (XEN) HVM1: BIOS map: >>> (XEN) HVM1: c8000-d47ff: Etherboot ROM >>> (XEN) HVM1: eb000-eb150: SMBIOS tables >>> (XEN) HVM1: f0000-fffff: Main BIOS >>> (XEN) HVM1: Invoking ROMBIOS ... >>> (XEN) HVM1: $Revision: 1.221 $ $Date: 2008/12/07 17:32:29 $ >>> (XEN) HVM1: Bochs BIOS - build: 06/23/99 >>> (XEN) HVM1: $Revision: 1.221 $ $Date: 2008/12/07 17:32:29 $ >>> (XEN) HVM1: Options: apmbios pcibios eltorito PMM >>> (XEN) HVM1: >>> (XEN) HVM1: ata0-0: PCHS=16383/16/63 translation=lba LCHS=1024/255/63 >>> (XEN) HVM1: ata0 master: QEMU HARDDISK ATA-7 Hard-Disk (8192 MBytes) >>> (XEN) HVM1: IDE time out >>> (XEN) HVM1: >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 6c1ba000 REASON >>> 5 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 6c1ba >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 160 >>> (XEN) l2[160] = 0 >>> (XEN) l2[160] not present >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 6c1ba000 REASON >>> 5 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 6c1ba >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 160 >>> (XEN) l2[160] = 0 >>> (XEN) l2[160] not present >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 6c1ba000 REASON >>> 5 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 6c1ba >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 160 >>> (XEN) l2[160] = 0 >>> (XEN) l2[160] not present >>> (XEN) [VT-D]iommu.c:722: iommu_page_fault: iommu->reg = ffff828bfff56000 >>> (XEN) [VT-D]iommu.c:691: iommu_fault_status: Fault Overflow >>> (XEN) [VT-D]iommu.c:694: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:676: iommu_fault:DMA Write: 0:2.0 addr 6c1ba000 REASON >>> 5 iommu->reg = ffff828bfff56000 >>> (XEN) print_vtd_entries: iommu = ffff83017bfe2600 bdf = 0:2:0 gmfn = 6c1ba >>> (XEN) root_entry = ffff83017bfb8000 >>> (XEN) root_entry[0] = 17763a001 >>> (XEN) context = ffff83017763a000 >>> (XEN) context[10] = 201_1763c0001 >>> (XEN) l3 = ffff8301763c0000 >>> (XEN) l3_index = 1 >>> (XEN) l3[1] = 12ae77003 >>> (XEN) l2 = ffff83012ae77000 >>> (XEN) l2_index = 160 >>> (XEN) l2[160] = 0 >>> (XEN) l2[160] not present >>> (XEN) HVM1: >>> (XEN) HVM1: >>> (XEN) HVM1: Press F12 for boot menu. >>> (XEN) HVM1: >>> (XEN) HVM1: Booting from Hard Disk... >>> (XEN) HVM1: Booting from 0000:7c00 >>> (XEN) HVM1: int13_harddisk: function 15, unmapped device for ELDL=81 >>> (XEN) HVM1: *** int 15h function AX=e980, BX=006e not yet supported! >>> (XEN) irq.c:243: Dom1 PCI link 0 changed 5 -> 0 >>> (XEN) irq.c:243: Dom1 PCI link 1 changed 10 -> 0 >>> (XEN) irq.c:243: Dom1 PCI link 2 changed 11 -> 0 >>> (XEN) irq.c:243: Dom1 PCI link 3 changed 5 -> 0 >>> (XEN) domctl.c:845:d0 memory_map:remove: gfn=f1000 mfn=d0400 nr_mfns=400 >>> (XEN) domctl.c:845:d0 memory_map:remove: gfn=e0000 mfn=b0000 nr_mfns=10000 >>> (XEN) domctl.c:910:d0 ioport_map:remove f_gport=c210 f_mport=d220 np=8 >>> (XEN) domctl.c:835:d0 memory_map:add: gfn=f1000 mfn=d0400 nr_mfns=400 >>> (XEN) domctl.c:835:d0 memory_map:add: gfn=e0000 mfn=b0000 nr_mfns=10000 >>> (XEN) domctl.c:886:d0 ioport_map:add f_gport=c210 f_mport=d220 np=8 >>> (XEN) domctl.c:845:d0 memory_map:remove: gfn=f1000 mfn=d0400 nr_mfns=400 >>> (XEN) domctl.c:845:d0 memory_map:remove: gfn=e0000 mfn=b0000 nr_mfns=10000 >>> (XEN) domctl.c:910:d0 ioport_map:remove f_gport=c210 f_mport=d220 np=8 >>> (XEN) domctl.c:835:d0 memory_map:add: gfn=f1000 mfn=d0400 nr_mfns=400 >>> (XEN) domctl.c:835:d0 memory_map:add: gfn=e0000 mfn=b0000 nr_mfns=10000 >>> (XEN) domctl.c:886:d0 ioport_map:add f_gport=c210 f_mport=d220 np=8 >>> (XEN) [VT-D]iommu.c:1364:d0 domain_context_unmap:PCI: bdf = 0:2.0 >>> (XEN) [VT-D]iommu.c:1252:d0 domain_context_mapping:PCI: bdf = 0:2.0 >>> Disabling IRQ #16 >>> >> >> _______________________________________________ >> Xen-devel mailing list >> Xen-devel@xxxxxxxxxxxxxxxxxxx >> http://lists.xensource.com/xen-devel > > > _______________________________________________ > Xen-devel mailing list > Xen-devel@xxxxxxxxxxxxxxxxxxx > http://lists.xensource.com/xen-devel > _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |